MOXA PT-G510-4GTX4GSFP-PHR (01) PDF Document

The MOXA PT-G510-4GTX4GSFP-PHR is shipped with the following items. If any of these items are missing or damaged, please contact your customer service representative for assistance.

• PT-G510 switch

• DIN-rail kit

• Protective caps on SFP ports and USB Storage ports

• RJ45 to DB9 Cable

• Quick installation guide (printed)

• Substance Disclosure Table

• Product Certificate of Quality Inspection

• Product Notices

• Warranty card

The default settings for the MOXA PT-G510-4GTX4GSFP-PHR are as follows:

• Default IP address: 192.168.127.253

• Default Subnet Mask: 255.255.255.0

• Default Usernames: admin, user

• Default Password: moxa

The front panel of the MOXA PT-G510-4GTX4GSFP-PHR includes the following components:

• System LED Indicators

• Console Port

• USB Storage Port

• 100/1000Base SFP A/B Port

• 10/100/1000BaseT(X) Port

• 100/1000Base SFP Slots

• Power Connector

• Relay

The front panel of the MOXA PT-G510-4GTX4GSFP-PHR contains several LED indicators. The function of each LED is described in the tables below:

System LEDs

Redundancy LEDs

Port LEDs

The DIN-rail mounting kit is fixed to the back panel of the MOXA PT-G510-4GTX4GSFP-PHR by default. To install it, mount the device on a corrosion-free mounting rail that meets the EN 60715 standard.

STEP 1: Insert the upper lip of the DIN rail into the DIN-rail mounting kit.

STEP 2: Press the MOXA PT-G510-4GTX4GSFP-PHR towards the DIN rail until it snaps into place.

STEP 1: Pull down the latch on the mounting kit with a screwdriver.

STEP 2 & 3: Slightly pull the MOXA PT-G510-4GTX4GSFP-PHR forward and lift to remove it from the DIN rail.

The MOXA PT-G510-4GTX4GSFP-PHR series supports various types of power supplies:

• WV models come with two 24 to 48 VDC power inputs.

• HV models come with two 110 to 220 VDC/VAC power inputs.

This equipment is intended to be supplied by an external power source (UL listed/ IEC 60950-1/ IEC 62368-1) with an output rating of 24 to 48 VDC, 1.1 A (minimum) or 110 to 220 VDC, 0.3 A (minimum), and an ambient temperature of 75°C (minimum).

Yes, if you intend to use more than 220 VAC/VDC (combined total) to power the dual power inputs, you must consider the following scenarios:

*Applies even if the PWR1 and PWR2 configurations are reversed.

Before connecting the MOXA PT-G510-4GTX4GSFP-PHR to AC or DC power inputs, make sure the power source voltage is stable.

For HV Models:

STEP 1: Insert the positive/negative DC or line/neutral AC wires into the V+/V- or L/N terminals, respectively.

STEP 2: Use a flat-blade screwdriver to tighten the wire-clamps on the front of the terminal block connector to fasten the wires.

STEP 3: Insert the plastic terminal block connector prongs into the terminal block receptor.

For WV Models:

STEP 1: Insert the positive/negative DC wires into the V+/V- terminals, respectively.

STEP 2: Use a flat-blade screwdriver to tighten the wire-clamps on the front of the terminal block connector to fasten the wires.

STEP 3: Insert the plastic terminal block connector prongs into the terminal block receptor.

If you intend to only use one power input, be sure to disconnect the other power input (unplug the power cord or disconnect the power input from the L and N contacts). Only one power input LED will be on.

The relay contact of the 3-pin terminal block connector is used to detect user-configured events. The module provides normally open (NO) and normally closed (NC) circuits. Two wires are attached to the relay pins with normally close and normally open options. The function is as follows:

When wiring the relay contact, DI, and power inputs, we suggest using the cable type – AWG (American Wire Gauge) 16-24 (1.31-0.205 mm²) and the corresponding pin type cable terminals. The connector must be able to withstand torque at maximum 5 pound-inches. The rated temperature of wiring should be at least 105°C.

Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the ground screw (M4) to the grounding surface prior to connecting devices. Using a shielded cable achieves better electromagnetic resistance. Use a green-yellow grounding cable with a wire size AWG 18 or higher to ground this product to earth.

The MOXA PT-G510-4GTX4GSFP-PHR has one RJ45 console port (RS-232) located on the front panel. Use an RJ45-based cable to connect the console port to your PC’s COM port. You may then use a console terminal program to access the switch with a baudrate of 115200. The pin definition of the console port is as follows:

The USB storage port is on the front panel of the switch and has a type A connector. Use Moxa’s ABC-02-USB automatic backup configurator to connect to the USB port to perform configuration backup, firmware upgrade, or system log file backup. The pinout assignments are:

Use a pointed object, such as a straightened paper clip or toothpick, to depress the Reset button. When you do so, the STATE LED will start to blink about once per second. Continue to hold the button until the STATE LED begins blinking more rapidly; this indicates that the button has been depressed for five seconds. You can then release the Reset button to load factory default settings. DO NOT power off the switch when loading default settings.

When the ABC-02-USB is connected to the MOXA PT-G510-4GTX4GSFP-PHR, the reset button allows for a quick backup of configuration and event logs to the ABC-02-USB. Press the reset button to start backing up the current system configuration files and event logs to the ABC-02-USB. Note that when the ABC-02 is plugged in, you cannot reset to factory default by pressing the reset button.

Technology

Input Output Interface

Ethernet Interface

Power Parameters

Physical Characteristics

Environmental Limits

Standards and Certifications

Please observe the following safety warnings when installing and operating the MOXA PT-G510-4GTX4GSFP-PHR:

Safety First!

• Be sure to disconnect the power cord before installing and/or wiring your Ethernet Switch. Calculate the maximum possible current in each power wire and common wire. Observe all electrical codes dictating the maximum current allowable for each wire size. If the current goes above the maximum ratings, the wiring could overheat, which can cause serious damage to your equipment.

Laser Safety

• Use only a Laser Class 1 optical transceiver with this device.

Wiring Requirements

• Do not disconnect modules or wires unless power has been switched off or the area is known to be non-hazardous. The device may only be connected to the supply voltage shown on the type plate. The device is designed for operation with an isolated power supply, which means that the device may only be connected to the supply voltage connections and to the signal contact with an isolated power supply in compliance with IEC 62368-1/EN 62368-1/UL 62368-1.

Hot Surfaces

• External metal parts of this equipment are extremely hot. Before touching the equipment, you must take special precautions to protect your hands and body from serious injury.

Maintenance and Fuses

• To protect against the risk of fire, only replace the fuse with one that has the same type and rating.

• It is recommended to incorporate a readily accessible disconnect device into the building installation wiring. Importantly, ensure the power supply is disconnected before performing any maintenance.

• This equipment is designed to connect the earthed conductor of the D.C supply circuit to the equipment’s earthing conductor.

Restricted Access Locations

• This equipment is intended to be used in Restricted Access Locations, such as a computer room, with access limited to service personnel or users who have been instructed on how to handle the metal chassis of equipment that is very hot. The location should only be accessible with a key or through a security system.