Free English MOXA NPORT 5610-16-48V (03) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD MOXA NPORT 5610-16-48V (03) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What items are included in the package for the MOXA NPORT 5610-16-48V?
The MOXA NPORT 5610-16-48V package should contain the following items:
• 1 NPort 5600 Series serial device server
• Power cord (AC models only)
• 1 DIN-rail/wall-mounting kit: WK-45-01
• NPort 5600 Quick Installation Guide
Please notify your sales representative if any of the above items is missing or damaged.
What optional accessories are available for the MOXA NPORT 5610-16-48V?
The following optional accessories are available:
• CBL-RJ45M9-150: 8-pin RJ45 to DB9 male cable, 150 cm
• CBL-RJ45F9-150: 8-pin RJ45 to DB9 female cable, 150 cm
• CBL-RJ45M25-150: 8-pin RJ45 to DB25 male cable, 150 cm
• CBL-RJ45F25-150: 8-pin RJ45 to DB25 female cable, 150 cm
How do I reset the MOXA NPORT 5610-16-48V to its factory default settings?
To load factory defaults, use a pointed object to press the Reset button continuously for 5 seconds. Release the button after the Ready LED stops blinking.
What do the front panel LED indicators on the MOXA NPORT 5610-16-48V mean?
The front panel of the MOXA NPORT 5610-16-48V has several LED indicators, as described in the following table:
| Name | Color | Function |
|---|---|---|
| Ready | Off | Power is off, or power error condition exists. |
| Red | Steady on: Power is on and the NPort is booting up. | |
| Blinking: Indicates an IP conflict, or DHCP or BOOTP server did not respond properly. | ||
| Green | Steady on: Power is on and the NPort is functioning normally. Blinking: The NPort has been located by NPort Administrator’s Location function. |
|
| 1 to 16 | Orange | Serial port is receiving data. |
| Green | Serial port is transmitting data. | |
| Off | No data is being transmitted or received through the serial port. |
How do I operate the LCM panel on my MOXA NPORT 5610-16-48V?
There are four buttons on the front panel of the MOXA NPORT 5610-16-48V used to operate the LCM panel. From left to right, the buttons and their functions are:
| Button | Action |
|---|---|
| MENU | Activates the main menu, or returns to a lower level. |
| ^ | Scrolls up through a list of items shown on the LCM panel’s second line. |
| v | Scrolls down through a list of items shown on the LCM panel’s second line. |
| SEL | Selects the option listed on the LCM panel’s second line. |
Note: The wide temperature model does not come with LCM display panels or push buttons. All of the LCM descriptions apply only to standard temperature models.
What do the link indicators on the rear panel of an NPort 5650 fiber model signify?
The rear panels of the NPort 5650 fiber models have a link indicator with the following functions:
| LED Name | LED Color | LED Function |
|---|---|---|
| Link | Off | Fiber disconnected. |
| Green | Fiber connected, data not transmitting. | |
| Blinking | Fiber connected, data is transmitting. |
How do I perform the hardware installation for the MOXA NPORT 5610-16-48V?
Follow these steps for hardware installation:
STEP 1: After removing the NPort 5600 from the box, the first thing you should do is attach the power adapter.
STEP 2: Connecting the Power. Instructions for AC and DC models vary. For DC models like the MOXA NPORT 5610-16-48V, see the specific DC power connection instructions.
STEP 3: Connect the NPort 5600 to a network. Use a standard straight-through Ethernet cable to connect to a hub or switch. When setting up or testing the NPort 5600, you might find it convenient to connect directly to your computer’s Ethernet port. In this case, use a cross-over Ethernet cable.
STEP 4: Connect the NPort 5600’s serial port to a serial device.
Placement Options: You can place the NPort 5600 on a desktop or other horizontal surface.
How do I connect the DC power to my MOXA NPORT 5610-16-48V?
Connect the MOXA NPORT 5610-16-48V’s power cord to the DC connector, and then follow the steps given below, using the NPort 5610-8-48V as an example:
1. Loosen the screws on the V+ and V- terminals of the NPort’s terminal block.
2. Connect the power cord’s 48 VDC or -48 VDC wire to the terminal block’s V+ terminal.
3. Connect the power cord’s DC Power Ground wire to the terminal block’s V- terminal.
4. Tighten the terminal block screws.
The “Ready” LED will show a solid red color until the system is ready, at which time it will change to a green color. Note that the NPort 5610-8-48V can still operate even if the 48V/-48V and DC Power Ground are reversed.
How do I properly ground the DC model of the MOXA NPORT 5610-16-48V?
Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the ground screw to the grounding surface prior to connecting devices.
The Shielded Ground (SG), sometimes called Protected Ground, contact is the second contact from the right of the 5-pin power terminal block connector located on the rear panel of the NPort 5610-8-48V. Connect the SG wire to the Earth ground.
What is the default IP address for the MOXA NPORT 5610-16-48V, and what should I do if I forget it?
For the NPort’s configuration, the default IP address is:
LAN: Static; IP = 192.168.127.254; netmask = 255.255.255.0
If you have forgotten the NPort’s IP address, use the Device Search Utility (DSU) from your PC to locate the NPort. After searching the LAN for NPort units, the DSU will display the IP address of each unit.
What are the software installation instructions for the MOXA NPORT 5610-16-48V?
You may log in with the password moxa to change any settings. For first-time use, click the Wizard in the left navigation panel to configure the IP address, SSID, and security mode. For software installation, follow these steps:
• Download the NPort Windows Driver Manager and install it as the driver to run with Real COM mode of the NPort Series.
• Execute NPort Windows Driver Manager; then map the virtual COM ports on your Windows platform.
• You may refer to the pin assignment section to loop back pin 4 and pin 5 for the RS-232 interface to carry out a self test on the device.
• Use HyperTerminal or a similar program (you may download Moxa’s program, called PComm Lite) to test whether the device is good or not.
What are the RS-232 serial port pin assignments for the MOXA NPORT 5610-16-48V?
| Pin | RS-232 |
|---|---|
| 1 | DSR (in) |
| 2 | RTS(out) |
| 3 | GND |
| 4 | TxD(out) |
| 5 | RxD(in) |
| 6 | DCD(in) |
| 7 | CTS(in) |
| 8 | DTR(out) |
What are the serial port pinouts for the NPort 5630 models?
| Pin | RS-422/RS-485-4W | RS-485-2W |
|---|---|---|
| 1 | – | – |
| 2 | – | – |
| 3 | TxD+ | – |
| 4 | TxD- | – |
| 5 | RxD- | Data- |
| 6 | RxD+ | Data+ |
| 7 | GND | GND |
| 8 | – | – |
What are the serial port pinouts for the NPort 5650 models?
| Pin | RS-232 | RS-422/RS-485-4W | RS-485-2W |
|---|---|---|---|
| 1 | DSR | – | – |
| 2 | RTS | TxD+ | – |
| 3 | GND | GND | GND |
| 4 | TxD | TxD- | – |
| 5 | RxD | RxD+ | Data+ |
| 6 | DCD | RxD- | Data- |
| 7 | CTS | – | – |
| 8 | DTR | – | – |
How should I wire an RS-232 serial cable for my MOXA NPORT 5610-16-48V?
The following table shows the RS-232 wiring from the NPort 5610 RJ45 port to DB9 male, DB9 female, DB25 male, and DB25 female serial device ports.
| NPort 5610 Signal | RJ45 Pin | DB9-M Pin | DB9-F Pin | DB-25-M Pin | DB-25-F Pin | Serial Device Signal |
|---|---|---|---|---|---|---|
| DSR | 1 | 6 | 4 | 6 | 20 | DTR |
| RTS | 2 | 7 | 8 | 4 | 5 | CTS |
| GND | 3 | 5 | 5 | 7 | 7 | GND |
| TxD | 4 | 3 | 2 | 2 | 3 | RxD |
| RxD | 5 | 2 | 3 | 3 | 2 | TxD |
| DCD | 6 | 1 | 1 | 8 | 8 | DCD |
| CTS | 7 | 8 | 7 | 5 | 4 | RTS |
| DTR | 8 | 4 | 6 | 20 | 6 | DSR |
How do I wire a 2-wire RS-485 serial cable for an NPort 5630 model?
The following table shows the 2-wire RS-485 wiring from the NPort 5630 RJ45 port to DB9 male, DB9 female, DB25 male, and DB25 female serial device ports.
| NPort 5630 Signal | RJ45 Pin | DB9-M Pin | DB9-F Pin | DB-25-M Pin | DB-25-F Pin | Serial Device Signal |
|---|---|---|---|---|---|---|
| Data- | 5 | 2 | 3 | 3 | 2 | Data- |
| Data+ | 6 | 1 | 1 | 8 | 8 | Data+ |
| GND | 7 | 8 | 7 | 5 | 4 | GND |
How do I wire a 4-wire RS-485/RS-422 serial cable for an NPort 5630 model?
The following table shows the 4-wire RS-485/RS-422 wiring from the NPort 5630 RJ45 port to DB9 male, DB9 female, DB25 male, and DB25 female serial device ports.
| NPort 5630 Signal | RJ45 Pin | DB9-M Pin | DB9-F Pin | DB-25-M Pin | DB-25-F Pin | Serial Device Signal |
|---|---|---|---|---|---|---|
| TxD+ | 3 | 5 | 5 | 7 | 7 | RxD+ |
| TxD- | 4 | 3 | 2 | 2 | 3 | RxD- |
| RxD- | 5 | 2 | 3 | 3 | 2 | TxD- |
| RxD+ | 6 | 1 | 1 | 8 | 8 | TxD+ |
| GND | 7 | 8 | 7 | 5 | 4 | GND |
How do I wire a 4-wire RS-485/RS-422 serial cable for an NPort 5650 model?
The following table shows the 4-wire RS-485/RS-422 wiring from the NPort 5650 RJ45 port to DB9 male, DB9 female, DB25 male, and DB25 female serial device ports.
| NPort 5650 Signal | RJ45 Pin | DB9-M Pin | DB9-F Pin | DB-25-M Pin | DB-25-F Pin | Serial Device Signal |
|---|---|---|---|---|---|---|
| TxD+ | 2 | 7 | 8 | 4 | 5 | RxD+ |
| GND | 3 | 5 | 5 | 7 | 7 | GND |
| TxD- | 4 | 3 | 2 | 2 | 3 | RxD- |
| RxD+ | 5 | 2 | 3 | 3 | 2 | TxD+ |
| RxD- | 6 | 1 | 1 | 8 | 8 | TxD- |
How do I wire a 2-wire RS-485 serial cable for an NPort 5650 model?
The following table shows the 2-wire RS-485 wiring from the NPort 5650 RJ45 port to DB9 male, DB9 female, DB25 male, and DB25 female serial device ports.
| NPort 5650 Signal | RJ45 Pin | DB9-M Pin | DB9-F Pin | DB-25-M Pin | DB-25-F Pin | Serial Device Signal |
|---|---|---|---|---|---|---|
| GND | 3 | 5 | 5 | 7 | 7 | GND |
| Data+ | 5 | 2 | 3 | 3 | 2 | Data+ |
| Data- | 6 | 1 | 1 | 8 | 8 | Data- |
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD MOXA NPORT 5610-16-48V (03) PDF DOCUMENT