Free English MOXA NPORT 5650-8-T (02) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD MOXA NPORT 5650-8-T (02) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What items are included in the package for the MOXA NPORT 5650-8-T?
The MOXA NPORT 5650-8-T package should contain the following items:
• 1 NPort 5600 Series serial device server
• Power cord (AC models only)
• 1 DIN-rail/wall-mounting kit: WK-45-01
• NPort 5600 Quick Installation Guide
What optional accessories are available for the MOXA NPORT 5650-8-T?
The following optional accessories are available:
• CBL-RJ45M9-150: 8-pin RJ45 to DB9 male cable, 150 cm
• CBL-RJ45F9-150: 8-pin RJ45 to DB9 female cable, 150 cm
• CBL-RJ45M25-150: 8-pin RJ45 to DB25 male cable, 150 cm
• CBL-RJ45F25-150: 8-pin RJ45 to DB25 female cable, 150 cm
Does the wide temperature MOXA NPORT 5650-8-T model come with an LCM display and push buttons?
No, the wide temperature model does not come with LCM display panels or push buttons. All LCM descriptions apply only to standard temperature models.
How can I reset my MOXA NPORT 5650-8-T to factory defaults?
To load factory defaults, use a pointed object to press the Reset button continuously for 5 seconds. Release the button after the Ready LED stops blinking.
What do the LED indicators on the front panel of the MOXA NPORT 5650-8-T mean?
| Name | Color | Function |
|---|---|---|
| Ready | Off | Power is off, or power error condition exists. |
| Red | Steady on: Power is on and the NPort is booting up. Blinking: Indicates an IP conflict, or DHCP or BOOTP server did not respond properly. |
|
| Green | Steady on: Power is on and the NPort is functioning normally. Blinking: The NPort has been located by NPort Administrator’s Location function. |
|
| 1 to 16 | Orange | Serial port is receiving data. |
| Green | Serial port is transmitting data. | |
| Off | No data is being transmitted or received through the serial port. |
What do the link indicators on the rear panel of a fiber model MOXA NPORT 5650-8-T mean?
| LED Name | LED Color | LED Function |
|---|---|---|
| Link | Off | Fiber disconnected. |
| Green | Fiber connected, data not transmitting. | |
| Blinking | Fiber connected, data is transmitting. |
How do I perform the hardware installation for the MOXA NPORT 5650-8-T?
STEP 1: Attach Power Adapter
After removing the MOXA NPORT 5650-8-T from the box, the first thing you should do is attach the power adapter.
STEP 2: Connecting the Power
AC: Connect the 100-240 VAC power cord to the AC connector. The “Ready” LED will show a solid red color until the system is ready, at which time it will change to a green color.
DC: Connect the VDC’s power cord to the DC connector. For a model like the NPort 5610-8-48V, loosen the screws on the V+ and V- terminals. Connect the power cord’s 48 VDC or -48 VDC wire to the terminal block’s V+ terminal, and the power cord’s DC Power Ground wire to the terminal block’s V- terminal, and then tighten the terminal block screws. (Note: The NPort 5610-8-48V can still operate even if the 48V/-48V and DC Power Ground are reversed.) The “Ready” LED will show a solid red color until the system is ready, at which time it will change to a green color.
Grounding the NPort 5600 VDC:
Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the ground screw to the grounding surface prior to connecting devices. The Shielded Ground (sometimes called Protected Ground) contact is the second contact from the right of the 5-pin power terminal block connector. Connect the SG wire to the Earth ground.
STEP 3: Connect to a Network
Use a standard straight-through Ethernet cable to connect to a hub or switch. When setting up or testing, you might find it convenient to connect directly to your computer’s Ethernet port. In this case, use a cross-over Ethernet cable.
STEP 4: Connect to a Serial Device
Connect the MOXA NPORT 5650-8-T’s serial port to a serial device.
Placement Options:
You can place the device on a desktop or other horizontal surface.
What are the default network settings for the MOXA NPORT 5650-8-T?
The default IP address configuration is:
LAN: Static
IP = 192.168.127.254
netmask = 255.255.255.0
What should I do if I have forgotten the IP address of my MOXA NPORT 5650-8-T?
If you have forgotten the NPort’s IP address, use the Device Search Utility (DSU) from your PC to locate the NPort. After searching the LAN for NPort units, the DSU will display the IP address of each unit.
How do I perform software installation for the MOXA NPORT 5650-8-T?
You may log in with the password moxa to change any settings. For first-time use, click the Wizard in the left navigation panel to configure the IP address, SSID, and security mode. For other settings, use the factory defaults or modify them for your application.
For software installation:
• Download the NPort Windows Driver Manager and install it as the driver to run with Real COM mode of the NPort Series.
• Execute NPort Windows Driver Manager; then map the virtual COM ports on your Windows platform.
• You may refer to the pin assignment section to loop back pin 4 and pin 5 for the RS-232 interface to carry out a self test on the device.
• Use HyperTerminal or a similar program (you may download Moxa’s program, called PComm Lite) to test whether the device is good or not.
What are the serial port pin assignments for the MOXA NPORT 5650-8-T?
| Pin | RS-232 | RS-422/RS-485-4W | RS-485-2W |
|---|---|---|---|
| 1 | DSR | – | – |
| 2 | RTS | TxD+ | – |
| 3 | GND | GND | GND |
| 4 | TxD | TxD- | – |
| 5 | RxD | RxD+ | Data+ |
| 6 | DCD | RxD- | Data- |
| 7 | CTS | – | – |
| 8 | DTR | – | – |
How do I wire serial cables for RS-232 communication on the MOXA NPORT 5650-8-T?
The following table shows the pin connections from the NPort’s RJ45 port to various serial connectors for RS-232.
| NPort 5650 (RJ45) | Signal | DB9 Male | DB9 Female | DB25 Male | DB25 Female | Serial Device Signal |
|---|---|---|---|---|---|---|
| Pin 1 | DSR | Pin 6 | Pin 4 | Pin 6 | Pin 20 | DTR |
| Pin 2 | RTS | Pin 7 | Pin 8 | Pin 4 | Pin 5 | CTS |
| Pin 3 | GND | Pin 5 | Pin 5 | Pin 7 | Pin 7 | GND |
| Pin 4 | TxD | Pin 3 | Pin 2 | Pin 2 | Pin 3 | RxD |
| Pin 5 | RxD | Pin 2 | Pin 3 | Pin 3 | Pin 2 | TxD |
| Pin 6 | DCD | Pin 1 | Pin 1 | Pin 8 | Pin 8 | DCD |
| Pin 7 | CTS | Pin 8 | Pin 7 | Pin 5 | Pin 4 | RTS |
| Pin 8 | DTR | Pin 4 | Pin 6 | Pin 20 | Pin 6 | DSR |
How do I wire serial cables for RS-422/4-wire RS-485 communication on the MOXA NPORT 5650-8-T?
The following table shows the pin connections from the NPort’s RJ45 port to various serial connectors for RS-422/4-wire RS-485.
| NPort 5650 (RJ45) | Signal | DB9 Male | DB9 Female | DB25 Male | DB25 Female | Serial Device Signal |
|---|---|---|---|---|---|---|
| Pin 2 | TxD+ | Pin 7 | Pin 8 | Pin 4 | Pin 5 | RxD+ |
| Pin 3 | GND | Pin 5 | Pin 5 | Pin 7 | Pin 7 | GND |
| Pin 4 | TxD- | Pin 3 | Pin 2 | Pin 2 | Pin 3 | RxD- |
| Pin 5 | RxD+ | Pin 2 | Pin 3 | Pin 3 | Pin 2 | TxD+ |
| Pin 6 | RxD- | Pin 1 | Pin 1 | Pin 8 | Pin 8 | TxD- |
How do I wire serial cables for 2-wire RS-485 communication on the MOXA NPORT 5650-8-T?
The following table shows the pin connections from the NPort’s RJ45 port to various serial connectors for 2-wire RS-485.
| NPort 5650 (RJ45) | Signal | DB9 Male | DB9 Female | DB25 Male | DB25 Female | Serial Device Signal |
|---|---|---|---|---|---|---|
| Pin 3 | GND | Pin 5 | Pin 5 | Pin 7 | Pin 7 | GND |
| Pin 5 | Data+ | Pin 2 | Pin 3 | Pin 3 | Pin 2 | Data+ |
| Pin 6 | Data- | Pin 1 | Pin 1 | Pin 8 | Pin 8 | Data- |
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD MOXA NPORT 5650-8-T (02) PDF DOCUMENT