Free English MOXA NPORT 5610-16 (03) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD MOXA NPORT 5610-16 (03) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What items are included in the package for the MOXA NPORT 5610-16?
The MOXA NPORT 5610-16 package should contain the following items:
• 1 NPort 5600 Series serial device server
• Power cord (AC models only)
• 1 DIN-rail/wall-mounting kit: WK-45-01
• NPort 5600 Quick Installation Guide
Please notify your sales representative if any of the above items are missing or damaged.
What optional accessories are available for the MOXA NPORT 5610-16?
The following optional accessories are available for the MOXA NPORT 5610-16:
• CBL-RJ45M9-150: 8-pin RJ45 to DB9 male cable, 150 cm
• CBL-RJ45F9-150: 8-pin RJ45 to DB9 female cable, 150 cm
• CBL-RJ45M25-150: 8-pin RJ45 to DB25 male cable, 150 cm
• CBL-RJ45F25-150: 8-pin RJ45 to DB25 female cable, 150 cm
How do I reset my MOXA NPORT 5610-16 to its factory default settings?
To load the factory defaults on your MOXA NPORT 5610-16, use a pointed object to press the Reset button continuously for 5 seconds. You should release the button after the Ready LED stops blinking.
What do the front panel LED indicators on my MOXA NPORT 5610-16 mean?
The front panel of the MOXA NPORT 5610-16 has several LED indicators with the following functions:
| Name | Color | Function |
|---|---|---|
| Ready | Off | Power is off, or power error condition exists. |
| Red | Steady on: Power is on and the NPort is booting up. Blinking: Indicates an IP conflict, or DHCP or BOOTP server did not respond properly. |
|
| Green | Steady on: Power is on and the NPort is functioning normally. | |
| Blinking: The NPort has been located by NPort Administrator’s Location function. | ||
| 1 to 16 | Orange | Serial port is receiving data. |
| Green | Serial port is transmitting data. | |
| Off | No data is being transmitted or received through the serial port. |
How do I operate the LCM panel on my MOXA NPORT 5610-16?
The MOXA NPORT 5610-16 has four buttons on its front panel to operate the LCM panel. Note that wide temperature models do not come with an LCM display or push buttons. Going from left to right, the buttons and their actions are:
| Button | Action |
|---|---|
| MENU | Activates the main menu, or returns to a lower level. |
| ^ (Up Arrow) | Scrolls up through a list of items shown on the LCM panel’s second line. |
| v (Down Arrow) | Scrolls down through a list of items shown on the LCM panel’s second line. |
| SEL | Selects the option listed on the LCM panel’s second line. |
How do I perform the hardware installation for the MOXA NPORT 5610-16?
Follow these steps for hardware installation:
STEP 1: Attach the Power Adapter
After removing the MOXA NPORT 5610-16 from the box, the first step is to attach the power adapter.
STEP 2: Connect the Power
• AC Models: Connect the NPort 5600’s 100-240 VAC power cord to the AC connector. The “Ready” LED will show a solid red color until the system is ready, at which time it will change to a green color.
• DC Models: Connect the NPort 5600 VDC’s power cord to the DC connector. For detailed DC connection steps, please refer to the specific instructions for DC models.
STEP 3: Connect to a Network
Use a standard straight-through Ethernet cable to connect to a hub or switch. If you are setting up or testing the device by connecting it directly to your computer’s Ethernet port, use a cross-over Ethernet cable.
STEP 4: Connect to a Serial Device
Connect the MOXA NPORT 5610-16’s serial port to a serial device.
Placement Options
You can place the MOXA NPORT 5610-16 on a desktop or other horizontal surface.
How do I connect and ground a DC-powered MOXA NPORT 5610-16?
DC Power Connection (using NPort 5610-8-48V as an example):
1. Loosen the screws on the V+ and V- terminals of the NPort’s terminal block.
2. Connect the power cord’s 48 VDC or -48 VDC wire to the terminal block’s V+ terminal.
3. Connect the power cord’s DC Power Ground wire to the terminal block’s V- terminal.
4. Tighten the terminal block screws. (Note: The NPort 5610-8-48V can still operate even if the 48V/-48V and DC Power Ground are reversed.)
The “Ready” LED will show a solid red color until the system is ready, at which time it will change to a green color.
Grounding the NPort 5600 VDC:
Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the ground screw to the grounding surface prior to connecting devices. The Shielded Ground (SG) contact is the second contact from the right of the 5-pin power terminal block connector. Connect the SG wire to the Earth ground.
What are the default network settings for the MOXA NPORT 5610-16 and how do I begin software configuration?
For the MOXA NPORT 5610-16’s configuration, the default IP address is:
• LAN: Static
• IP Address: 192.168.127.254
• Netmask: 255.255.255.0
If you have forgotten the NPort’s IP address, use the Device Search Utility (DSU) from your PC to locate it. After searching the LAN for NPort units, the DSU will display the IP address of each unit.
You may log in with the password moxa to change any settings to meet your network topology or serial device parameters. For first-time use, you can use the Wizard in the left navigation panel to configure the IP address, SSID, and security mode. For other settings, use the factory defaults or modify the settings for your application.
What are the serial port pin assignments for the MOXA NPORT 5610-16?
The serial port pinouts for the MOXA NPORT 5610-16, which uses an RS-232 interface, are as follows:
| Pin | RS-232 |
|---|---|
| 1 | DSR (in) |
| 2 | RTS(out) |
| 3 | GND |
| 4 | TxD(out) |
| 5 | RxD(in) |
| 6 | DCD(in) |
| 7 | CTS(in) |
| 8 | DTR(out) |
What are the serial port pinouts for other models in the same series as the MOXA NPORT 5610-16, such as the NPort 5630?
The serial port pinouts for the NPort 5630 models are as follows:
| Pin | RS-422/RS-485-4W | RS-485-2W |
|---|---|---|
| 1 | – | – |
| 2 | – | – |
| 3 | TxD+ | – |
| 4 | TxD- | – |
| 5 | RxD- | Data- |
| 6 | RxD+ | Data+ |
| 7 | GND | GND |
| 8 | – | – |
What are the serial port pinouts for the NPort 5650 models, which are in the same series as the MOXA NPORT 5610-16?
The serial port pinouts for the NPort 5650 models, which support RS-232, RS-422, and RS-485, are as follows:
| Pin | RS-232 | RS-422/RS-485-4W | RS-485-2W |
|---|---|---|---|
| 1 | DSR | – | – |
| 2 | RTS | TxD+ | – |
| 3 | GND | GND | GND |
| 4 | TxD | TxD- | – |
| 5 | RxD | RxD+ | Data+ |
| 6 | DCD | RxD- | Data- |
| 7 | CTS | – | – |
| 8 | DTR | – | – |
How should I wire the serial cables for an RS-232 connection on my MOXA NPORT 5610-16?
The following table shows the cable wiring between the RJ45 port on the MOXA NPORT 5610-16 and various DB connectors for an RS-232 serial device.
| NPort RJ45 Pin | Signal | DB9-M Pin | DB9-F Pin | DB-25-M Pin | DB-25-F Pin | Serial Device Signal |
|---|---|---|---|---|---|---|
| 1 | DSR | 6 | 4 | 6 | 20 | DTR |
| 2 | RTS | 7 | 8 | 4 | 5 | CTS |
| 3 | GND | 5 | 5 | 7 | 7 | GND |
| 4 | TxD | 3 | 2 | 2 | 3 | RxD |
| 5 | RxD | 2 | 3 | 3 | 2 | TxD |
| 6 | DCD | 1 | 1 | 8 | 8 | DCD |
| 7 | CTS | 8 | 7 | 5 | 4 | RTS |
| 8 | DTR | 4 | 6 | 20 | 6 | DSR |
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD MOXA NPORT 5610-16 (03) PDF DOCUMENT