MOXA NPORT 5650-16-M-SC (02) PDF Document

The MOXA NPORT 5650-16-M-SC package should contain the following items:

• 1 NPort 5600 Series serial device server

• Power cord (AC models only)

• 1 DIN-rail/wall-mounting kit: WK-45-01

• NPort 5600 Quick Installation Guide

The following optional accessories are available:

• CBL-RJ45M9-150: 8-pin RJ45 to DB9 male cable, 150 cm

• CBL-RJ45F9-150: 8-pin RJ45 to DB9 female cable, 150 cm

• CBL-RJ45M25-150: 8-pin RJ45 to DB25 male cable, 150 cm

• CBL-RJ45F25-150: 8-pin RJ45 to DB25 female cable, 150 cm

To load the factory default settings, use a pointed object to press the Reset button continuously for 5 seconds. You can release the button after the Ready LED stops blinking.

If the device is working properly, the LCM panel will display a green color. After the red Ready LED turns green, you will see a display similar to:

N P 5 6 1 0 – 1 6 3 8

1 9 2 1 6 8 1 2 7 2 5 4

This display indicates:

• NP5610-16 is the NPort’s name

• 38 is the NPort’s local sequence number

• 192.168.127.254 is the NPort’s IP address

NOTE: Wide temperature models do not come with LCM display panels or push buttons. The LCM descriptions apply only to standard temperature models.

There are four buttons on the front panel used to operate the LCM panel. From left to right, the buttons are:

STEP 1: After removing the device from the box, the first step is to attach the power adapter.

STEP 2: Connect the power. Depending on your model, follow the AC or DC instructions.

• AC: Connect the 100-240 VAC power cord to the AC connector. The “Ready” LED will show a solid red color until the system is ready, at which time it will change to a green color.

• DC: Connect the VDC power cord to the DC connector. For a model like the NPort 5610-8-48V, loosen the screws on the V+ and V- terminals. Connect the power cord’s 48 VDC or -48 VDC wire to the V+ terminal and the DC Power Ground wire to the V- terminal, then tighten the screws. (Note: The NPort 5610-8-48V can still operate even if the 48V/-48V and DC Power Ground are reversed.) The “Ready” LED will show a solid red color until the system is ready, then it will change to green.

STEP 3: Connect the MOXA NPORT 5650-16-M-SC to a network. Use a standard straight-through Ethernet cable to connect to a hub or switch. If you are connecting directly to a computer’s Ethernet port for setup or testing, use a cross-over Ethernet cable.

STEP 4: Connect the device’s serial port to a serial device.

Placement Options: You can place the MOXA NPORT 5650-16-M-SC on a desktop or other horizontal surface.

Grounding and wire routing help limit the effects of noise from electromagnetic interference (EMI). Before connecting devices, run the ground connection from the ground screw to the grounding surface.

The Shielded Ground (SG), sometimes called Protected Ground, is the second contact from the right of the 5-pin power terminal block connector on the rear panel of the NPort 5610-8-48V. Connect the SG wire to the Earth ground.

For configuration, the default IP address settings are:

LAN: Static

IP Address: 192.168.127.254

Netmask: 255.255.255.0

If you have forgotten the device’s IP address, use the Device Search Utility (DSU) from your PC to locate the device. After searching the LAN for NPort units, the DSU will display the IP address of each unit it finds.

You can log in with the password moxa to change settings to match your network topology or serial device parameters. For first-time use, click the Wizard in the left navigation panel, which will prompt you to configure the IP address, SSID, and security mode. For other settings, you can use the factory defaults or modify them for your application.

For software installation, follow these steps:

1. Download the NPort Windows Driver Manager and install it as the driver to run with Real COM mode of the NPort Series.

2. Execute NPort Windows Driver Manager, and then map the virtual COM ports on your Windows platform.

3. You may refer to the pin assignment section to loop back pin 4 and pin 5 for the RS-232 interface to carry out a self-test on the device.

4. Use HyperTerminal or a similar program (like Moxa’s PComm Lite) to test whether the device is functioning correctly.

The following table shows the RJ45 to DB9 and DB25 connections for an RS-232 serial device.

The following table shows the RJ45 to DB9 and DB25 connections for a 2-wire RS-485 serial device.

The following table shows the RJ45 to DB9 and DB25 connections for an RS-422 or 4-wire RS-485 serial device.