Free English MOXA NPORT 5610-8 (03) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD MOXA NPORT 5610-8 (03) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What is included in the MOXA NPORT 5610-8 package?
The MOXA NPORT 5610-8 package should contain the following items:
• 1 NPort 5600 Series serial device server
• Power cord (AC models only)
• 1 DIN-rail/wall-mounting kit: WK-45-01
• NPort 5600 Quick Installation Guide
Note: Please notify your sales representative if any of the above items is missing or damaged.
What optional accessories are available for the MOXA NPORT 5610-8?
The following optional accessories are available:
• CBL-RJ45M9-150: 8-pin RJ45 to DB9 male cable, 150 cm
• CBL-RJ45F9-150: 8-pin RJ45 to DB9 female cable, 150 cm
• CBL-RJ45M25-150: 8-pin RJ45 to DB25 male cable, 150 cm
• CBL-RJ45F25-150: 8-pin RJ45 to DB25 female cable, 150 cm
Do wide temperature models of the MOXA NPORT 5610-8 come with an LCM display?
No, the wide temperature model does not come with LCM display panels or push buttons. All LCM descriptions apply only to standard temperature models.
How do I load the factory defaults on my MOXA NPORT 5610-8?
To load factory defaults, press the Reset button continuously for 5 seconds. You should use a pointed object to press the reset button. Release the button after the Ready LED stops blinking.
What do the front panel LED indicators on the MOXA NPORT 5610-8 mean?
| Name | Color | Function |
|---|---|---|
| Ready | Off | Power is off, or power error condition exists. |
| Red | Steady on: Power is on and the NPort is booting up. Blinking: Indicates an IP conflict, or DHCP or BOOTP server did not respond properly. |
|
| Green | Steady on: Power is on and the NPort is functioning normally. Blinking: The NPort has been located by NPort Administrator’s Location function. |
|
| 1 to 16 | Orange | Serial port is receiving data. |
| Green | Serial port is transmitting data. | |
| Off | No data is being transmitted or received through the serial port. |
What information is displayed on the LCM panel of my MOXA NPORT 5610-8?
If the MOXA NPORT 5610-8 is working properly, the LCM panel will display a green color. After the red Ready LED turns green, you will see a display similar to:
NP5610-16 38
192.168.127.254
This is where:
• NP5610-16 is the NPort’s name
• 38 is the NPort’s local sequence number
• 192.168.127.254 is the NPort’s IP address
How do I operate the LCM panel on my MOXA NPORT 5610-8?
There are four buttons on the front panel of the MOXA NPORT 5610-8, from left to right, used to operate the LCM panel.
| Button | Action |
|---|---|
| MENU | Activates the main menu, or returns to a lower level. |
| ∧ (Up Arrow) | Scrolls up through a list of items shown on the LCM panel’s second line. |
| ∨ (Down Arrow) | Scrolls down through a list of items shown on the LCM panel’s second line. |
| SEL | Selects the option listed on the LCM panel’s second line. |
What do the link indicators on the rear panel of the NPort 5650 fiber model mean?
The rear panels of the NPort 5650 fiber models have a link indicator with the following functions:
| LED Name | LED Color | LED Function |
|---|---|---|
| Link | Off | Fiber disconnected. |
| Green | Fiber connected, data not transmitting. | |
| Blinking | Fiber connected, data is transmitting. |
What are the hardware installation steps for the MOXA NPORT 5610-8?
STEP 1: Attach the power adapter
After removing the MOXA NPORT 5610-8 from the box, the first thing you should do is attach the power adapter.
STEP 2: Connecting the Power
AC: Connect the NPort 5600’s 100-240 VAC power cord to the AC connector. The “Ready” LED will show a solid red color until the system is ready, at which time it will change to a green color.
DC: Connect the NPort 5600 VDC’s power cord to the DC connector, and then follow the steps given below. For example, with the NPort 5610-8-48V:
1. Loosen the screws on the V+ and V- terminals of the NPort 5610-8-48V’s terminal block.
2. Connect the power cord’s 48 VDC or -48 VDC wire to the terminal block’s V+ terminal, and the power cord’s DC Power Ground wire to the terminal block’s V- terminal.
3. Tighten the terminal block screws. (Note: The NPort 5610-8-48V can still operate even if the 48V/-48V and DC Power Ground are reversed.)
The “Ready” LED will show a solid red color until the system is ready, at which time it will change to a green color.
Grounding the NPort 5600 VDC:
Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the ground screw to the grounding surface prior to connecting devices. The Shielded Ground (sometimes called Protected Ground) contact is the second contact from the right of the 5-pin power terminal block connector located on the rear panel of the NPort 5610-8-48V. Connect the SG wire to the Earth ground.
STEP 3: Connect to a network
Use a standard straight-through Ethernet cable to connect the MOXA NPORT 5610-8 to a hub or switch. When setting up or testing the device, you might find it convenient to connect directly to your computer’s Ethernet port. In this case, use a cross-over Ethernet cable.
STEP 4: Connect to a serial device
Connect the MOXA NPORT 5610-8’s serial port to a serial device.
Placement Options: You can place the MOXA NPORT 5610-8 on a desktop or other horizontal surface.
What is the default IP address for the MOXA NPORT 5610-8?
For the MOXA NPORT 5610-8 configuration, the default IP address is:
LAN: Static; IP = 192.168.127.254; netmask = 255.255.255.0
How can I find the IP address of my MOXA NPORT 5610-8 if it is forgotten?
If you have forgotten the IP address of the MOXA NPORT 5610-8, use the Device Search Utility (DSU) from your PC to locate the device. After searching the LAN for NPort units, the DSU will display the IP address of each unit.
How do I perform the initial software configuration for my MOXA NPORT 5610-8?
You may log in with the password moxa to change any settings to meet your network topology (e.g., IP address) or serial device (e.g., serial parameters). For first-time use, click the Wizard in the left navigation panel. The wizard will prompt you to configure the IP address, SSID, and security mode. For other settings, use the factory defaults or modify the settings for your application.
For software installation:
• Download the NPort Windows Driver Manager and install it as the driver to run with Real COM mode of the NPort Series.
• Execute NPort Windows Driver Manager; then map the virtual COM ports on your Windows platform.
• You may refer to the pin assignment section to loop back pin 4 and pin 5 for the RS-232 interface to carry out a self test on the device.
• Use HyperTerminal or a similar program (you may download Moxa’s program, called PComm Lite) to test whether the device is good or not.
What are the serial port pinouts for the MOXA NPORT 5610-8?
The RJ45 serial port on the MOXA NPORT 5610-8 has the following RS-232 pinouts:
| Pin | RS-232 |
|---|---|
| 1 | DSR (in) |
| 2 | RTS(out) |
| 3 | GND |
| 4 | TxD(out) |
| 5 | RxD(in) |
| 6 | DCD(in) |
| 7 | CTS(in) |
| 8 | DTR(out) |
What are the serial port pinouts for the NPort 5630 models?
| Pin | RS-422/RS-485-4W | RS-485-2W |
|---|---|---|
| 1 | – | – |
| 2 | – | – |
| 3 | TxD+ | – |
| 4 | TxD- | – |
| 5 | RxD- | Data- |
| 6 | RxD+ | Data+ |
| 7 | GND | GND |
| 8 | – | – |
What are the serial port pinouts for the NPort 5650 models?
| Pin | RS-232 | RS-422/RS-485-4W | RS-485-2W |
|---|---|---|---|
| 1 | DSR | – | – |
| 2 | RTS | TxD+ | – |
| 3 | GND | GND | GND |
| 4 | TxD | TxD- | – |
| 5 | RxD | RxD+ | Data+ |
| 6 | DCD | RxD- | Data- |
| 7 | CTS | – | – |
| 8 | DTR | – | – |
How should I wire an RS-232 serial cable for my MOXA NPORT 5610-8?
The following table details the pin connections for wiring an RS-232 serial cable from the RJ45 port of a MOXA NPORT 5610-8 to various DB connectors on a serial device.
| NPort 5610 RJ45 Pin | NPort Signal | Connects To Pin on Serial Device Connector | Serial Device Signal |
|---|---|---|---|
| 1 | DSR | DB9-M (6), DB9-F (4), DB25-M (6), DB25-F (20) | DTR |
| 2 | RTS | DB9-M (7), DB9-F (8), DB25-M (4), DB25-F (5) | CTS |
| 3 | GND | DB9-M (5), DB9-F (5), DB25-M (7), DB25-F (7) | GND |
| 4 | TxD | DB9-M (3), DB9-F (2), DB25-M (2), DB25-F (3) | RxD |
| 5 | RxD | DB9-M (2), DB9-F (3), DB25-M (3), DB25-F (2) | TxD |
| 6 | DCD | DB9-M (1), DB9-F (1), DB25-M (8), DB25-F (8) | DCD |
| 7 | CTS | DB9-M (8), DB9-F (7), DB25-M (5), DB25-F (4) | RTS |
| 8 | DTR | DB9-M (4), DB9-F (6), DB25-M (20), DB25-F (6) | DSR |
How should I wire a 2-wire RS-485 serial cable for an NPort 5630 model?
The following table details the pin connections for wiring a 2-wire RS-485 serial cable from the RJ45 port of an NPort 5630 to various DB connectors on a serial device.
| NPort 5630 RJ45 Pin | NPort Signal | Connects To Pin on Serial Device Connector | Serial Device Signal |
|---|---|---|---|
| 5 | Data- | DB9-M (2), DB9-F (3), DB25-M (3), DB25-F (2) | Data- |
| 6 | Data+ | DB9-M (1), DB9-F (1), DB25-M (8), DB25-F (8) | Data+ |
| 7 | GND | DB9-M (8), DB9-F (7), DB25-M (5), DB25-F (4) | GND |
How should I wire an RS-422/4-wire RS-485 serial cable for an NPort 5630 model?
The following table details the pin connections for wiring an RS-422/4-wire RS-485 serial cable from the RJ45 port of an NPort 5630 to various DB connectors on a serial device.
| NPort 5630 RJ45 Pin | NPort Signal | Connects To Pin on Serial Device Connector | Serial Device Signal |
|---|---|---|---|
| 3 | TxD+ | DB9-M (5), DB9-F (5), DB25-M (7), DB25-F (7) | RxD+ |
| 4 | TxD- | DB9-M (3), DB9-F (2), DB25-M (2), DB25-F (3) | RxD- |
| 5 | RxD- | DB9-M (2), DB9-F (3), DB25-M (3), DB25-F (2) | TxD- |
| 6 | RxD+ | DB9-M (1), DB9-F (1), DB25-M (8), DB25-F (8) | TxD+ |
| 7 | GND | DB9-M (8), DB9-F (7), DB25-M (5), DB25-F (4) | GND |
How should I wire an RS-422/4-wire RS-485 serial cable for an NPort 5650 model?
The following table details the pin connections for wiring an RS-422/4-wire RS-485 serial cable from the RJ45 port of an NPort 5650 to various DB connectors on a serial device.
| NPort 5650 RJ45 Pin | NPort Signal | Connects To Pin on Serial Device Connector | Serial Device Signal |
|---|---|---|---|
| 2 | TxD+ | DB9-M (7), DB9-F (8), DB25-M (4), DB25-F (5) | RxD+ |
| 3 | GND | DB9-M (5), DB9-F (5), DB25-M (7), DB25-F (7) | GND |
| 4 | TxD- | DB9-M (3), DB9-F (2), DB25-M (2), DB25-F (3) | RxD- |
| 5 | RxD+ | DB9-M (2), DB9-F (3), DB25-M (3), DB25-F (2) | TxD+ |
| 6 | RxD- | DB9-M (1), DB9-F (1), DB25-M (8), DB25-F (8) | TxD- |
How should I wire a 2-wire RS-485 serial cable for an NPort 5650 model?
The following table details the pin connections for wiring a 2-wire RS-485 serial cable from the RJ45 port of an NPort 5650 to various DB connectors on a serial device.
| NPort 5650 RJ45 Pin | NPort Signal | Connects To Pin on Serial Device Connector | Serial Device Signal |
|---|---|---|---|
| 3 | GND | DB9-M (5), DB9-F (5), DB25-M (7), DB25-F (7) | GND |
| 5 | Data+ | DB9-M (2), DB9-F (3), DB25-M (3), DB25-F (2) | Data+ |
| 6 | Data- | DB9-M (1), DB9-F (1), DB25-M (8), DB25-F (8) | Data- |
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD MOXA NPORT 5610-8 (03) PDF DOCUMENT