Free English MOXA NPORT 5650-16-HV-T (02) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD MOXA NPORT 5650-16-HV-T (02) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What is included in the package for the MOXA NPORT 5650-16-HV-T?
The MOXA NPORT 5650-16-HV-T package should contain the following items:
• 1 NPort 5600 Series serial device server
• Power cord (AC models only)
• 1 DIN-rail/wall-mounting kit: WK-45-01
• NPort 5600 Quick Installation Guide
What optional accessories are available for the MOXA NPORT 5650-16-HV-T?
The following optional accessories are available:
• CBL-RJ45M9-150: 8-pin RJ45 to DB9 male cable, 150 cm
• CBL-RJ45F9-150: 8-pin RJ45 to DB9 female cable, 150 cm
• CBL-RJ45M25-150: 8-pin RJ45 to DB25 male cable, 150 cm
• CBL-RJ45F25-150: 8-pin RJ45 to DB25 female cable, 150 cm
Does the MOXA NPORT 5650-16-HV-T come with an LCM display panel and push buttons?
No, the MOXA NPORT 5650-16-HV-T is a wide temperature model and does not come with LCM display panels or push buttons. Descriptions of LCM functionality apply only to standard temperature models.
How do I reset the MOXA NPORT 5650-16-HV-T to factory defaults?
To load factory defaults, press the Reset button continuously for 5 seconds using a pointed object. Release the button after the Ready LED stops blinking.
What are the functions of the front panel LED indicators on the MOXA NPORT 5650-16-HV-T?
The front panel LED indicators have the following functions:
| Name | Color | Function |
|---|---|---|
| Ready | Off | Power is off, or power error condition exists. |
| Red | Steady on: Power is on and the NPort is booting up. Blinking: Indicates an IP conflict, or DHCP or BOOTP server did not respond properly. |
|
| Green | Steady on: Power is on and the NPort is functioning normally. Blinking: The NPort has been located by NPort Administrator’s Location function. |
|
| 1 to 16 | Orange | Serial port is receiving data. |
| Green | Serial port is transmitting data. | |
| Off | No data is being transmitted or received through the serial port. |
How do I interpret the LCM Display Panel on standard temperature NPort 5600 models?
If the NPort is working properly, the LCM panel will display a green color. After the red Ready LED turns green, the display will show information similar to the example below:
First Line: N P 5 6 1 0 – 1 6
Second Line: 1 9 2 . 1 6 8 . 1 2 7 . 2 5 4
In this example:
• NP5610-16 is the NPort’s name
• 38 is the NPort’s local sequence number
• 192.168.127.254 is the NPort’s IP address
How do I operate the LCM Panel on standard temperature NPort 5600 models?
There are four buttons on the front panel used to operate the server’s LCM panel. Going from left to right, the buttons are:
| Button | Action |
|---|---|
| MENU | Activates the main menu, or returns to a lower level. |
| ^ | Scrolls up through a list of items shown on the LCM panel’s second line. |
| v | Scrolls down through a list of items shown on the LCM panel’s second line. |
| SEL | Selects the option listed on the LCM panel’s second line. |
What do the rear panel Link Indicators mean on the NPort 5650 fiber model?
| LED Name | LED Color | LED Function |
|---|---|---|
| Link | Off | Fiber disconnected. |
| Green | Fiber connected, data not transmitting. | |
| Blinking | Fiber connected, data is transmitting. |
How do I perform the hardware installation for the MOXA NPORT 5650-16-HV-T?
Follow these steps for hardware installation:
STEP 1: After removing the device from the box, attach the power adapter.
STEP 2: Connecting the Power.
AC Models: Connect the NPort 5600’s 100-240 VAC power cord to the AC connector. The “Ready” LED will show a solid red color until the system is ready, at which time it will change to a green color.
DC Models: Connect the power cord to the DC connector. For a model like the NPort 5610-8-48V:
1. Loosen the screws on the V+ and V- terminals of the terminal block.
2. Connect the power cord’s 48 VDC or -48 VDC wire to the terminal block’s V+ terminal.
3. Connect the power cord’s DC Power Ground wire to the terminal block’s V- terminal.
4. Tighten the terminal block screws. (Note: The NPort 5610-8-48V can still operate even if the 48V/-48V and DC Power Ground are reversed.)
The “Ready” LED will show a solid red color until the system is ready, at which time it will change to a green color.
Grounding the NPort 5600 VDC: Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the ground screw to the grounding surface prior to connecting devices. The Shielded Ground (SG) contact is the second contact from the right of the 5-pin power terminal block connector. Connect the SG wire to the Earth ground.
STEP 3: Connect the NPort 5600 to a network. Use a standard straight-through Ethernet cable to connect to a hub or switch. When setting up or testing, you may find it convenient to connect directly to your computer’s Ethernet port using a cross-over Ethernet cable.
STEP 4: Connect the NPort 5600’s serial port to a serial device.
Placement Options: You can place the NPort 5600 on a desktop or other horizontal surface.
How do I install the software for the MOXA NPORT 5650-16-HV-T?
The default IP address of the NPort is:
LAN: Static; IP = 192.168.127.254; netmask = 255.255.255.0
If you have forgotten the IP address, use the Device Search Utility (DSU) from your PC to locate the NPort. After searching the LAN for NPort units, the DSU will display the IP address of each unit.
You may log in with the password moxa to change any settings. For first-time use, click the Wizard in the left navigation panel to configure the IP address, SSID, and security mode. For other settings, use the factory defaults or modify the settings for your application.
For software installation, download the relative utilities from Moxa’s website and follow these steps:
• Download the NPort Windows Driver Manager and install it as the driver to run with Real COM mode of the NPort Series.
• Execute NPort Windows Driver Manager; then map the virtual COM ports on your Windows platform.
• You may refer to the pin assignment section to loop back pin 4 and pin 5 for the RS-232 interface to carry out a self test on the device.
• Use HyperTerminal or a similar program (you may download Moxa’s program, called PComm Lite) to test whether the device is good or not.
What are the serial port pin assignments for the MOXA NPORT 5650-16-HV-T and related models?
The pin assignments for the RJ45 serial ports are as follows:
NPort 5610 Pinouts
| Pin | RS-232 |
|---|---|
| 1 | DSR (in) |
| 2 | RTS(out) |
| 3 | GND |
| 4 | TxD(out) |
| 5 | RxD(in) |
| 6 | DCD(in) |
| 7 | CTS(in) |
| 8 | DTR(out) |
NPort 5630 Pinouts
| Pin | RS-422/RS-485-4W | RS-485-2W |
|---|---|---|
| 1 | – | – |
| 2 | – | – |
| 3 | TxD+ | – |
| 4 | TxD- | – |
| 5 | RxD- | Data- |
| 6 | RxD+ | Data+ |
| 7 | GND | GND |
| 8 | – | – |
MOXA NPORT 5650-16-HV-T Pinouts
| Pin | RS-232 | RS-422/RS-485-4W | RS-485-2W |
|---|---|---|---|
| 1 | DSR | – | – |
| 2 | RTS | TxD+ | – |
| 3 | GND | GND | GND |
| 4 | TxD | TxD- | – |
| 5 | RxD | RxD+ | Data+ |
| 6 | DCD | RxD- | Data- |
| 7 | CTS | – | – |
| 8 | DTR | – | – |
How should I wire an RS-232 serial cable for the MOXA NPORT 5650-16-HV-T?
The following table shows the cable wiring for an RS-232 connection between the NPort 5610/5650 RJ45 port and a serial device with DB9 or DB25 connectors.
| NPort 5610/5650 (RJ45) |
Signal | DB9 Male | DB9 Female | DB25 Male | DB25 Female | Serial Device Signal |
|---|---|---|---|---|---|---|
| 1 | DSR | 6 | 4 | 6 | 20 | DTR |
| 2 | RTS | 7 | 8 | 4 | 5 | CTS |
| 3 | GND | 5 | 5 | 7 | 7 | GND |
| 4 | TxD | 3 | 2 | 2 | 3 | RxD |
| 5 | RxD | 2 | 3 | 3 | 2 | TxD |
| 6 | DCD | 1 | 1 | 8 | 8 | DCD |
| 7 | CTS | 8 | 7 | 5 | 4 | RTS |
| 8 | DTR | 4 | 6 | 20 | 6 | DSR |
How do I wire a 2-wire RS-485 serial cable for the NPort 5630?
The following table shows the cable wiring for a 2-wire RS-485 connection between the NPort 5630 RJ45 port and a serial device with DB9 or DB25 connectors.
| NPort 5630 (RJ45) |
Signal | DB9 Male | DB9 Female | DB25 Male | DB25 Female | Serial Device Signal |
|---|---|---|---|---|---|---|
| 5 | Data- | 2 | 3 | 3 | 2 | Data- |
| 6 | Data+ | 1 | 1 | 8 | 8 | Data+ |
| 7 | GND | 8 | 7 | 5 | 4 | GND |
How do I wire an RS-422/4-wire RS-485 serial cable for the NPort 5630?
The following table shows the cable wiring for an RS-422/4-wire RS-485 connection between the NPort 5630 RJ45 port and a serial device with DB9 or DB25 connectors.
| NPort 5630 (RJ45) |
Signal | DB9 Male | DB9 Female | DB25 Male | DB25 Female | Serial Device Signal |
|---|---|---|---|---|---|---|
| 3 | TxD+ | 5 | 5 | 7 | 7 | RxD+ |
| 4 | TxD- | 3 | 2 | 2 | 3 | RxD- |
| 5 | RxD- | 2 | 3 | 3 | 2 | TxD- |
| 6 | RxD+ | 1 | 1 | 8 | 8 | TxD+ |
| 7 | GND | 8 | 7 | 5 | 4 | GND |
How should I wire an RS-422/4-wire RS-485 serial cable for the MOXA NPORT 5650-16-HV-T?
The following table shows the cable wiring for an RS-422/4-wire RS-485 connection between the MOXA NPORT 5650-16-HV-T RJ45 port and a serial device with DB9 or DB25 connectors.
| NPort 5650 (RJ45) |
Signal | DB9 Male | DB9 Female | DB25 Male | DB25 Female | Serial Device Signal |
|---|---|---|---|---|---|---|
| 2 | TxD+ | 7 | 8 | 4 | 5 | RxD+ |
| 3 | GND | 5 | 5 | 7 | 7 | GND |
| 4 | TxD- | 3 | 2 | 2 | 3 | RxD- |
| 5 | RxD+ | 2 | 3 | 3 | 2 | TxD+ |
| 6 | RxD- | 1 | 1 | 8 | 8 | TxD- |
How should I wire a 2-wire RS-485 serial cable for the MOXA NPORT 5650-16-HV-T?
The following table shows the cable wiring for a 2-wire RS-485 connection between the MOXA NPORT 5650-16-HV-T RJ45 port and a serial device with DB9 or DB25 connectors.
| NPort 5650 (RJ45) |
Signal | DB9 Male | DB9 Female | DB25 Male | DB25 Female | Serial Device Signal |
|---|---|---|---|---|---|---|
| 3 | GND | 5 | 5 | 7 | 7 | GND |
| 5 | Data+ | 2 | 3 | 3 | 2 | Data+ |
| 6 | Data- | 1 | 1 | 8 | 8 | Data- |
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD MOXA NPORT 5650-16-HV-T (02) PDF DOCUMENT