Free English MOXA NPORT 5610-8-48V (03) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD MOXA NPORT 5610-8-48V (03) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What is the MOXA NPORT 5610-8-48V and what are its features?
The MOXA NPORT 5610-8-48V is part of the NPort 5600 Series of serial device servers. The series includes various models with different port configurations:
• The NPort 5610-8/16 has 8 or 16 RS-232 ports.
• The NPort 5630-8/16 has 8 or 16 RS-422/485 ports.
• The NPort 5650-8/16 has 8 or 16 RS-232/422/485 ports.
Which models are included in the NPort 5600 Series?
The NPort 5600 Series includes the following models:
• NPort 5610-8
• NPort 5610-16
• NPort 5610-8-48V
• NPort 5610-16-48V
• NPort 5630-8
• NPort 5630-16
• NPort 5650-8
• NPort 5650-8-T
• NPort 5650-8-HV-T
• NPort 5650-16-HV-T
• NPort 5650-16
• NPort 5650-16-T
• NPort 5650-8-M-SC
• NPort 5650-16-M-SC
• NPort 5650-8-S-SC
• NPort 5650-16-S-SC
What items are included in the package for the MOXA NPORT 5610-8-48V?
The NPort 5600 package should contain the following items:
• 1 NPort 5600 Series serial device server
• Power cord (AC models only)
• 1 DIN-rail/wall-mounting kit: WK-45-01
• NPort 5600 Quick Installation Guide
What optional accessories are available for the MOXA NPORT 5610-8-48V?
The following optional accessories are available:
• CBL-RJ45M9-150: 8-pin RJ45 to DB9 male cable, 150 cm
• CBL-RJ45F9-150: 8-pin RJ45 to DB9 female cable, 150 cm
• CBL-RJ45M25-150: 8-pin RJ45 to DB25 male cable, 150 cm
• CBL-RJ45F25-150: 8-pin RJ45 to DB25 female cable, 150 cm
How do I reset the MOXA NPORT 5610-8-48V to its factory defaults?
To load factory defaults, use a pointed object to press the Reset button continuously for 5 seconds. Release the button after the Ready LED stops blinking.
What do the front panel LED indicators on the MOXA NPORT 5610-8-48V mean?
The front panel of the NPort 5600 has several LED indicators with the following functions:
| Name | Color | Function |
|---|---|---|
| Ready | Off | Power is off, or power error condition exists. |
| Red | Steady on: Power is on and the NPort is booting up. | |
| Blinking: Indicates an IP conflict, or DHCP or BOOTP server did not respond properly. | ||
| Green | Steady on: Power is on and the NPort is functioning normally. Blinking: The NPort has been located by NPort Administrator’s Location function. |
|
| 1 to 16 | Orange | Serial port is receiving data. |
| Green | Serial port is transmitting data. | |
| Off | No data is being transmitted or received through the serial port. |
How do I interpret the LCM Display Panel on standard temperature models of the MOXA NPORT 5610-8-48V?
If the NPort is working properly, the LCM panel will display a green color. The red Ready LED will also light up, indicating that the NPort is receiving power. After the red Ready LED turns green, you will see a display similar to:
NP5610-16 38
192.168.127.254
This display indicates:
• NP5610-16 is the NPort’s name.
• 38 is the NPort’s local sequence number.
• 192.168.127.254 is the NPort’s IP address.
NOTE: Wide temperature models do not come with LCM display panels or push buttons. The descriptions apply only to standard temperature models.
How do I operate the LCM panel on standard temperature models of the MOXA NPORT 5610-8-48V?
There are four buttons on the front panel used to operate the server’s LCM panel. From left to right, the buttons and their actions are:
| Button | Action |
|---|---|
| MENU | Activates the main menu, or returns to a lower level. |
| ^ (Up Arrow) | Scrolls up through a list of items shown on the LCM panel’s second line. |
| v (Down Arrow) | Scrolls down through a list of items shown on the LCM panel’s second line. |
| SEL | Selects the option listed on the LCM panel’s second line. |
What do the Link Indicators on the rear panel of the NPort 5650 fiber model mean?
The rear panels of the NPort 5650 fiber model have a link indicator with the following functions:
| LED Name | LED Color | LED Function |
|---|---|---|
| Link | Off | Fiber disconnected. |
| Green | Fiber connected, data not transmitting. | |
| Blinking | Fiber connected, data is transmitting. |
What are the steps for hardware installation of the MOXA NPORT 5610-8-48V?
STEP 1: Attach the Power Adapter
After removing the NPort 5600 from the box, the first step is to attach the power adapter.
STEP 2: Connecting and Grounding DC Power
Connect the NPort 5600 VDC’s power cord to the DC connector. Follow these steps for the MOXA NPORT 5610-8-48V:
1. Loosen the screws on the V+ and V- terminals of the NPort 5610-8-48V’s terminal block.
2. Connect the power cord’s 48 VDC or -48 VDC wire to the terminal block’s V+ terminal, and the power cord’s DC Power Ground wire to the terminal block’s V- terminal.
3. Tighten the terminal block screws. (Note: The NPort 5610-8-48V can still operate even if the 48V/-48V and DC Power Ground are reversed.)
The “Ready” LED will show a solid red color until the system is ready, at which time it will change to a green color.
Grounding the NPort 5600 VDC: Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the ground screw to the grounding surface prior to connecting devices. The Shielded Ground (SG) contact is the second contact from the right of the 5-pin power terminal block connector. Connect the SG wire to the Earth ground.
STEP 3: Connect to a Network
Use a standard straight-through Ethernet cable to connect to a hub or switch. If you are connecting directly to a computer’s Ethernet port for setup or testing, use a cross-over Ethernet cable.
STEP 4: Connect to a Serial Device
Connect the NPort 5600’s serial port to a serial device.
Placement Options
You can place the NPort 5600 on a desktop or other horizontal surface.
What is the default IP address for the MOXA NPORT 5610-8-48V?
For the NPort’s configuration, the default IP address is:
• LAN: Static
• IP: 192.168.127.254
• Netmask: 255.255.255.0
What should I do if I forget the IP address of my MOXA NPORT 5610-8-48V?
If you have forgotten the NPort’s IP address, use the Device Search Utility (DSU) from your PC to locate the NPort. After searching the LAN for NPort units, the DSU will display the IP address of each unit.
How do I log in and perform the initial configuration of the MOXA NPORT 5610-8-48V?
You may log in with the password moxa to change any settings to meet your network topology (e.g., IP address) or serial device (e.g., serial parameters). For first-time use, click the Wizard in the left navigation panel. The wizard will prompt you to configure the IP address, SSID, and security mode. For other settings, use the factory defaults or modify the settings for your application.
How do I install the necessary software for the MOXA NPORT 5610-8-48V?
For software installation, follow these steps:
1. Download the NPort Windows Driver Manager and install it as the driver to run with Real COM mode of the NPort Series.
2. Execute NPort Windows Driver Manager; then map the virtual COM ports on your Windows platform.
3. You may refer to the pin assignment section to loop back pin 4 and pin 5 for the RS-232 interface to carry out a self test on the device.
4. Use HyperTerminal or a similar program (such as PComm Lite) to test whether the device is good or not.
What are the serial port pin assignments for the MOXA NPORT 5610-8-48V?
| Pin | RS-232 |
|---|---|
| 1 | DSR (in) |
| 2 | RTS(out) |
| 3 | GND |
| 4 | TxD(out) |
| 5 | RxD(in) |
| 6 | DCD(in) |
| 7 | CTS(in) |
| 8 | DTR(out) |
What are the serial port pin assignments for the NPort 5630 model?
| Pin | RS-422/RS-485-4W | RS-485-2W |
|---|---|---|
| 1 | – | – |
| 2 | – | – |
| 3 | TxD+ | – |
| 4 | TxD- | – |
| 5 | RxD- | Data- |
| 6 | RxD+ | Data+ |
| 7 | GND | GND |
| 8 | – | – |
What are the serial port pin assignments for the NPort 5650 model?
| Pin | RS-232 | RS-422/RS-485-4W | RS-485-2W |
|---|---|---|---|
| 1 | DSR | – | – |
| 2 | RTS | TxD+ | – |
| 3 | GND | GND | GND |
| 4 | TxD | TxD- | – |
| 5 | RxD | RxD+ | Data+ |
| 6 | DCD | RxD- | Data- |
| 7 | CTS | – | – |
| 8 | DTR | – | – |
What is the serial cable wiring for RS-232 on the MOXA NPORT 5610-8-48V?
| NPort 5610/5650 (RJ45) | Serial Port Connector | Serial Device | |||||
|---|---|---|---|---|---|---|---|
| Pin | Signal | DB9-M | DB9-F | DB-25-M | DB-25-F | Pin | Signal |
| 1 | DSR | 6 | 4 | 6 | 20 | DTR | |
| 2 | RTS | 7 | 8 | 4 | 5 | CTS | |
| 3 | GND | 5 | 5 | 7 | 7 | GND | |
| 4 | TxD | 3 | 2 | 2 | 3 | RxD | |
| 5 | RxD | 2 | 3 | 3 | 2 | TxD | |
| 6 | DCD | 1 | 1 | 8 | 8 | DCD | |
| 7 | CTS | 8 | 7 | 5 | 4 | RTS | |
| 8 | DTR | 4 | 6 | 20 | 6 | DSR | |
What is the serial cable wiring for 2-wire RS-485 on the NPort 5630?
| NPort 5630 (RJ45) | Serial Port Connector | Serial Device | |||||
|---|---|---|---|---|---|---|---|
| Pin | Signal | DB9-M | DB9-F | DB-25-M | DB-25-F | Pin | Signal |
| 5 | Data- | 2 | 3 | 3 | 2 | Data- | |
| 6 | Data+ | 1 | 1 | 8 | 8 | Data+ | |
| 7 | GND | 8 | 7 | 5 | 4 | GND | |
What is the serial cable wiring for RS-422/4-wire RS-485 on the NPort 5630?
| NPort 5630 (RJ45) | Serial Port Connector | Serial Device | |||||
|---|---|---|---|---|---|---|---|
| Pin | Signal | DB9-M | DB9-F | DB-25-M | DB-25-F | Pin | Signal |
| 3 | TxD+ | 5 | 5 | 7 | 7 | RxD+ | |
| 4 | TxD- | 3 | 2 | 2 | 3 | RxD- | |
| 5 | RxD- | 2 | 3 | 3 | 2 | TxD- | |
| 6 | RxD+ | 1 | 1 | 8 | 8 | TxD+ | |
| 7 | GND | 8 | 7 | 5 | 4 | GND | |
What is the serial cable wiring for RS-422/4-wire RS-485 on the NPort 5650?
| NPort 5650 (RJ45) | Serial Port Connector | Serial Device | |||||
|---|---|---|---|---|---|---|---|
| Pin | Signal | DB9-M | DB9-F | DB-25-M | DB-25-F | Pin | Signal |
| 2 | TxD+ | 7 | 8 | 4 | 5 | RxD+ | |
| 3 | GND | 5 | 5 | 7 | 7 | GND | |
| 4 | TxD- | 3 | 2 | 2 | 3 | RxD- | |
| 5 | RxD+ | 2 | 3 | 3 | 2 | TxD+ | |
| 6 | RxD- | 1 | 1 | 8 | 8 | TxD- | |
What is the serial cable wiring for 2-wire RS-485 on the NPort 5650?
| NPort 5650 (RJ45) | Serial Port Connector | Serial Device | |||||
|---|---|---|---|---|---|---|---|
| Pin | Signal | DB9-M | DB9-F | DB-25-M | DB-25-F | Pin | Signal |
| 3 | GND | 5 | 5 | 7 | 7 | GND | |
| 5 | Data+ | 2 | 3 | 3 | 2 | Data+ | |
| 6 | Data- | 1 | 1 | 8 | 8 | Data- | |
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD MOXA NPORT 5610-8-48V (03) PDF DOCUMENT