LOST VAPE Q-ULTRA AIO KIT (01) PDF Document

The basic parameters for the LOST VAPE Q-ULTRA AIO KIT are as follows:

The package for the LOST VAPE Q-ULTRA AIO KIT includes:

1x Q-ULTRA UNIT (0.8Ω PRE-INSTALLED)

1x ULTRA BOOST 1.0Ω MTL COIL

1x TYPE-C USB CABLE

1x USER MANUAL

1x WARRANTY CARD

To turn the LOST VAPE Q-ULTRA AIO KIT on or off, consistently press the Fire button 5 times. The screen displays “Lost Vape” once the device is turned on.

To adjust the airflow on the LOST VAPE Q-ULTRA AIO KIT, rotate the Airflow Control Ring to adjust.

To reset the puff counter on the LOST VAPE Q-ULTRA AIO KIT, press the Up and Down buttons simultaneously to set the puffs.

To lock or unlock the wattage settings on the LOST VAPE Q-ULTRA AIO KIT, press the Fire button 3 times. The screen will display “Wattage lock/unlock” indicating the status.

To charge the LOST VAPE Q-ULTRA AIO KIT, insert the Type-C USB cable into the Charging Port connected to a power source. The battery icon will be animating while charging and the screen will show “Fully charged” once fully charged.

The security protection messages on the LOST VAPE Q-ULTRA AIO KIT screen indicate the following:

Too Hot: Shows “Too Hot” when the device overheats.

Low Battery: Shows “Low Battery” when the battery is running low.

Short Circuit Protection: The device cannot be used when short circuit protection is active.

Check Atomizer: Indicates an issue with the atomizer connection.

Over 10s: Appears if the Fire button is held down for more than 10 seconds.

The compatible coil series for the LOST VAPE Q-ULTRA AIO KIT include:

Ultra Boost 0.3Ω Mesh Coil

Ultra Boost 0.6Ω M4 Mesh Coil

Ultra Boost 1.0Ω MTL Coil

Ultra Boost F3 0.9Ω OCC Coil

The steps to fill the e-liquid in the LOST VAPE Q-ULTRA AIO KIT pod are as follows:

STEP 1: Remove the pod from the device.

STEP 2: Open the Refill Cap.

STEP 3: Fill the pod with e-liquid. Ensure not to overfill.

STEP 4: Once the filling is completed, close the Refill Cap.

To install the pod cartridge into the LOST VAPE Q-ULTRA AIO KIT device:

STEP 1: Slide down the pod lock/unlock button.

STEP 2: Put the pod in the right place, making sure the airflow hole is facing the side of the airflow control ring.

STEP 3: Slide the pod lock/unlock button back to lock the pod.

The steps to replace the coil in the LOST VAPE Q-ULTRA AIO KIT pod are:

STEP 1: Remove the pod from the device.

STEP 2: Pull out the old coil directly.

STEP 3: Prime the new coil with a few drops of e-liquid on the cotton wick.

STEP 4: Align the new coil with the hole in the pod and push it firmly into place. Then, put the pod back into the device.

Safety warnings for the LOST VAPE Q-ULTRA AIO KIT include:

Warning For Vulnerable Consumer Groups: The sale and use of e-cigarettes is prohibited to persons under legal age. Keep this product out of the reach of children. Do not use this product if you are pregnant or breastfeeding. Use by a non-smoker is not recommended.

Battery Caution: Do not expose the device to extreme temperatures. Do not overcharge the batteries. Do not use this product if the battery casing is damaged or the battery appears to overheat. Dispose of Lithium Polymer batteries at suitable recycling and waste disposal facilities.

E-liquids: Only use E-LIQUIDS WHICH COMPLY WITH EUROPEAN UNION LAW IN THIS PRODUCT. Please consult with an expert if you are unsure.

Pod Cartridge Attention: Do not use refilled or empty pods. It is essential to fully saturate the coil before first use.