LOST VAPE CENTAURUS B80 AIO (01) PDF MANUAL

This product is not recommended for minors, non-smokers, pregnant or breastfeeding women, persons with or at risk of heart disease, or persons taking medication for depression or asthma.

Warning for Vulnerable Consumer Groups: This product is not recommended for use by young people, non-smokers, pregnant or breastfeeding women, or persons who are allergic/sensitive to nicotine.

Do not expose the device to extreme temperatures.

Do not drop, throw, or abuse the device as it may cause damage.

Do not allow water or other liquids to come into contact with the electronics.

Keep the device away from heat sources to avoid damage.

Tank Attention: Do not slip down the tank. Do not puncture the tank. If liquid leaks from the tank or comes into contact with skin, wash thoroughly with soap and water. If the tank gets damaged, do not vape with it. If you ingest the liquid, contact your local medical authority or a local poison control center immediately. All spilled liquid should be cleaned up immediately. Keep the tank out of reach of children and pets.

Do not attempt to repair the product by yourself as damage or personal injury may occur.

The device is covered by a 9-month warranty from the date of purchase.

For further questions or issues, please contact Lost Vape for assistance.

5-80W Max Output Power

UB AIO Pod

0.96” OLED Screen

Fit for Single Battery

Replaceable Side Panel

Type-C Fast Charging

Dimension	85*43*25.5mm
Net Weight	150±5g
Pod Capacity	5ml (Standard) / 2ml (TPD)
Battery	Single 18650 Battery (Not Included)
Battery Voltage	3.0V-4.2V
Power Range	5-80W
Charging Voltage	5V/1.8A
Type-C Cable	Supports 5V/2A Charger
Display Pixel	0.96” 96*96
Coil Resistance Supported	0.15Ω-2.0Ω
Safety Features	Short-Circuit Protection / Weak Battery Protection / Over Heat Protection / 10 Seconds Over-time Protection
Body Material	Zinc-Alloy & Stainless Steels

1. Unscrew the bottom cap of the tank.

2. Pull out the used coil.

3. Insert a new coil into the tank.

4. Screw the bottom cap back onto the tank.

5. Fill the pod with e-liquid and wait 5 minutes before use.

1. Open the battery door panel.

2. Insert a single 18650 battery following the correct polarity markings (+/-) located on the battery door.

3. Ensure the battery is securely installed.

4. Close the battery door panel.

1. Choose the desired airflow hole.

2. Pull down the lock/release switch.

3. Push the filled UB AIO Pod Tank into the device until it is fully seated.

Press the fire button 5 times consecutively within 2 seconds to turn the device ON or OFF.

1. Press the Fire Button to vape when the power is on.

2. Press the Right (+) or Left (-) button to increase/decrease the power level. If you press and hold the Right (+) or Left (-) button, the power level value will start to increase/decrease quickly until you release the button or reach the max/min power level.

3. In Wattage Mode (Normal Mode / RBA Mode), pressing the button to vape will stop the wattage setting and change the screen interface back to the power value. While the device has low power, it can remain in standby mode, but it will show a “Low Battery” warning when you press the fire button.

In RBA Mode, you can construct an RBA coil (sold separately), and not recommended to use any pre-made coil, it will burn the coil quickly.

When RBA mode is used, it is ideally within a record to work under the RBA mode. The resistance range of RBA should be between 0.1Ω and 3.0Ω (Highest resistance recommended is 0.8Ω).

Press and hold both the Right (+) and Left (-) buttons simultaneously for 2 seconds to lock or unlock the adjustment setting. The fire button will still work under the “LOCKED” status.

1. Press the Fire button to check the puff display (if puff count > 0).

2. Press the Fire button and Left (-) button at the same time for 2s to reset the puff count.

Simply plug in the Type-C cable to the port located on the device, connect the other end to a power source (Type-C fast charging).

The screen will display a charging animation when charging.

The battery icon indicates the charge level:

0-19%: Empty battery icon

20-39%: One bar filled

40-59%: Two bars filled

60-79%: Three bars filled

80-95%: Four bars filled

95-100%: Full battery icon (Charging will stop automatically when fully charged)

The display shows the battery percentage and estimated remaining charge time.

Indicates the battery voltage is lower than 3.0V. Replace or recharge the battery.

The device did not detect the atomizer/coil, or the atomizer/coil resistance is too high. Check the connection and coil installation. The screen will display for a few seconds after attempting to vape.

Indicates the atomizer/coil resistance is too low (below 0.1Ω) or there is a short circuit. Check the coil and connection.

Indicates the internal temperature of the device has reached 60°C/140°F. Stop using the device and allow it to cool down.

If the fire button is pressed continuously for longer than 10 seconds, the output will automatically cut off and the screen shows “Over 10s”. Release the button and press again to continue vaping.