DURASTAR DRF2TA3624ASTNJB5 (01) PDF Document

The DURASTAR DRF2TA3624ASTNJB5 air handler includes the following features and benefits:

• Front or Bottom Return with aluminum tube and fin coil

• TXV for cooling or heat pump operation

• Wall-hanging brackets

• Built in Filter Rack

• Molex Plug Connections for field installed heater kits

• Dual Voltage Direct Drive Blower with multi-speed motor

• Thermoplastic Drain Pan with bottom primary and secondary connections

• Optional Decorative Grill for front return applications

• Optional Factory Installed Condensate Float Switch which shuts off the outdoor unit in the event the condensate pan becomes clogged

• Cabinet air leakage less than 2% at 1 inch H2O when tested in accordance with ASHRAE Standard 193

• Can be field wired for single or two stage applications

The standard equipment for the DURASTAR DRF2TA3624ASTNJB5 includes:

• Exclusive Incoloy sheath type electric heating elements

• Field convertible air supply

• Durable framed cleanable air filter

• Indoor coil design provides low air side pressure drop, high performance and compact size

• PVC condensate elbow is standard on all coils

• All indoor coils have aluminum tubing and aluminum fins

• Molded polymer corrosion resistant condensate drain pan

• Supply and return duct flanges

• High and low voltage connection points inside cabinet

• Concentric knockouts provided for power connection with hole size up to 2 inches [51 mm] for 1 1/2 inch [38mm] conduit

• Internal checked TX valves for quiet refrigerant metering

• Front refrigerant and drain connection

The model number for the DURASTAR DRF2TA series is broken down as follows:

[] Designates Metric Conversions

[] Designates Metric Conversions

Airflow performance data is based on cooling performance with a coil and no filter in place. For optimum blower performance, operate the unit in the .3 [8 mm] to .7 inches [18 mm] W.C. external static range. Units with coils should be applied with a minimum of .1 inch [3 mm] W.C. external static range.

[] Designates Metric Conversions

NOTE: All DRF2TA air-handlers have 5 speed constant torque motors.

Speed tap 1 is for continuous fan. Speed tap 2 (low static) and speed tap 3 (high static) are for lower tonnage (1.5 or 2.5 tons). Speed tap 4 (low static) and speed tap 5 (high static) are for higher tonnage (2.0 or 3.0 tons).

DRF2TA air handlers are always shipped from factory at speed tap 5.

The low static speed tap 2 (lower tonnage) and 4 (higher tonnage) are for external static pressures below 0.5″ WC. The high static speed tap 3 (lower tonnage) and 5 (higher tonnage) are used for external static exceeding 0.5″ WC. Move the blue wire to the appropriate speed tap on the motor terminal block as required by the application needs.

The airflow for continuous fan (speed tap 1) is always set at 50% of the speed tap 4.

• The above airflow table lists the airflow information for air handlers with maximum heater allowed for each model.

*Blower motors are all single phase motors.

Installation of the U.L. Listed original equipment manufacturer provided heater kits listed in the table below is recommended for all auxiliary heating requirements.

• Electric heater BTUH – (heater watts + motor watts) x 3.414 (see airflow table for motor watts.)

• J voltage (230V) single phase air handler is designed to be used with single or three phase.

• Supply circuit protective devices may be fused or “HACR” type circuit breakers.

• If non-standard fuse size is specified, use next size larger standard fuse size. Without the heater, bring only two leads to terminal block, cap, insulate and fully secure the third lead.

• Largest motor load is included in single circuit or circuit 1 of multiple circuits.

• Do not use 480 volts electrical heaters on 230 volts air handler.

• Field wiring must comply with the National Electrical Code.

• This product must be sufficiently grounded in accordance with (C.E.C. in Canada) and any applicable local ordinance. National Electrical Code (C.E.C. in Canada) and any applicable.

• Supply wiring must be 75°C minimum copper conductors only. Local ordinance.

• See electrical data for product Ampacity rating and Circuit.

• A grounding lug is provided. Protector requirement.

The following accessories, kits, and parts are available for your air handler:

• Drain Pan Over Flow Switch RXHK-A01: This is used to detect condensate drain blockage and will shut down the outdoor unit in order to prevent structural damage to the surrounding structures of the air handler.

• Bottom Return Conversion Kit RXHK-B02: This kit is used to divert the return air from the factory standard front return to a bottom return.

• Louvered Cabinet Grill RXHK-C02: This is used as a decorative grill which covers the return air opening of the front return air handler.

• Decorative Wall Grill RXHK-D01 or RXHK-D02: This is used in applications where the air handler is installed in a closet or interior wall and allows adequate return air back to the unit.

All DURASTAR DRF2TA3624ASTNJB5 units are configured for vertical upflow. The units cannot be installed in any other configuration.

A clearance of 24 inches (610 mm) is required in front of the DURASTAR DRF2TA3624ASTNJB5 for filter and coil maintenance.