SONY BRAVIA KD-49XG81XX (02) PDF Document

Count how many times it flashes (the interval time is three seconds).

Reboot the SONY BRAVIA KD-49XG81XX by disconnecting the mains lead until the illumination LED stops flashing in red, then turn on the TV. If the problem persists, disconnect the mains lead, and contact your dealer or Sony service centre with the number of times the illumination LED flashes.

Restart your SONY BRAVIA KD-49XG81XX by pressing the power button on the remote control until a message appears. The TV will restart. If the TV does not recover, try unplugging the mains lead. Then press the power button on the TV and wait for two minutes, and plug in the mains lead.

Refer to the Help menu by pressing HELP on the remote control.

Sony strongly recommends you to update the TV software by selecting [Update Now]. These software updates improve your TV performance or add new features. The following screen with [Updating…] will appear and the illumination LED flashes white while software is updating. Do not unplug the mains lead during the software update. If you do, the software update may not finish completely, and it may cause a software malfunction. Software updates can take up to 15 minutes.

When you plug in the TV, the TV may not be able to turn on for a while even if you press the power button on the remote control or the TV. It takes time to initialize the system. Wait for about one minute, then operate it again.

For more detailed information, select [Help Guide] from the Help menu on your TV. You can also check the Help Guide from your PC or smartphone (information provided on the back cover of this manual).

Connect and set up the IR Blaster (models with supplied IR Blaster only). Connect an HDMI CEC compatible device (except models with supplied IR Blaster) and change to that input.

Enter 9999 for the PIN code and select [Change PIN code].

Replace the batteries.

When the TV is off, press  to power on. When the TV is on, press and hold  to power off.

Press  repeatedly to change the function, then press + or – button to: Adjust the volume, Select the channel, or Select the input source of TV.

1   +/– (Power) /+/-: When the TV is off, Press  to power on. When the TV is on, Press and hold  to power off. Press  repeatedly to change the function, then press + or – button to: Adjust the volume, Select the channel, Select the input source of TV.

2 Remote Control sensor* / Light sensor* / Illumination LED: The illumination LED lights up or blinks according to the status of the TV. For more information, refer to the Help Guide. * Do not place anything near the sensor.

Switch to a TV channel or input and display the TV Menu Bar.

Return to the previous screen or exit from the menu. When an Interactive Application service is available, press to exit from the service.

In TV mode: Display and select the input source. In Text mode: Hold the current page.

Record the currently viewed programme on the USB HDD.

Display the Help menu. Help Guide can be accessed from here.

On screen menu navigation and selection.

Use voice search*. (e.g., Search various content by voice.) * The voice search requires an Internet connection.

Display the connected External Box (cable/satellite box) menu. For models with supplied IR Blaster, connect and set up the IR Blaster. The External Box menu may be displayed for some HDMI CEC compatible devices when the IR Blaster is not supplied/connected.

Number buttons are used for direct access to channels or to display information.

Execute corresponding function at that time.

Display a list of contextual functions.

Display the digital programme guide, or EPG of External Box (cable/satellite box) after setting [IR Blaster setup] (IR Blaster compatible models only).

Return to the previous screen.

Display the TV Home Menu.

Adjust the volume.

Jump back and forth between two channels or inputs. The TV alternates between the current channel or input and the last channel or input that was selected.

Mute the sound. Press again to restore the sound.

In TV mode: Select the channel. In Text mode: Select the next () or previous () page.

Select the sound of multilingual source or dual sound for the programme currently being viewed (depend on programme source).

Operate media contents on the TV and connected BRAVIA Sync-compatible device.

Turn subtitles on or off (when the feature is available).

Access the “Google Play” online service.

Access the “NETFLIX” online service. (Only on limited region/country/TV model)

The dimensions (approx.) (w × h × d) with Table-Top Stand for the SONY BRAVIA KD-49XG81XX are 110.1 × 70.4 × 26.2 cm.

The dimensions (approx.) (w × h × d) without Table-Top Stand for the SONY BRAVIA KD-49XG81XX are 110.1 × 64.5 × 5.7 cm.

The approximate mass (Approx.) with Table-Top Stand for the SONY BRAVIA KD-49XG81XX is 12.4 kg.

The approximate mass (Approx.) without Table-Top Stand for the SONY BRAVIA KD-49XG81XX is 11.8 kg.

The required screws are M6 screws (not supplied) with a length of 8 mm – 12 mm. The torque specification for the cord (not supplied) is 1.5 N·m {15 kgf·cm}.

The power consumption for the SONY BRAVIA KD-49XG81XX in [Standard] mode is 77 W.

The power consumption for the SONY BRAVIA KD-49XG81XX in [Vivid] mode (KD-49XG8196 / 49XG8096) is 120 W.

The annual energy consumption for the SONY BRAVIA KD-49XG81xx / 49XG80xx is 107 kWh per year.

The standby power consumption is 0.50 W (25 W in software/EPG update mode).

The display resolution is 3,840 dots (horizontal) × 2,160 lines (vertical).

USB 1/2: 5 V , 500 mA MAX. USB 3: 5 V , 900 mA MAX.

The specifications for Wireless LAN (IEEE 802.11ac/a/b/g/n) for the SONY BRAVIA KD-49XG81XX are:

The specifications for Bluetooth frequency range and output power for the SONY BRAVIA KD-49XG81XX (using RMF-TX310E/TX220E) are:

The specifications for Bluetooth frequency range and output power for the SONY BRAVIA KD-49XG81XX (using RMF-TX310E/TX220E model for Bluetooth) are:

The operating temperature is 0 ºC – 40 ºC.

The operating humidity is 10 % – 80 % RH (non-condensing).

The dimensions (Approx.) (w × h × d) without Table-Top Stand for the SONY BRAVIA KD-49XG80xx are 110.1 × 64.5 × 5.7 cm.

Use of screws other than those supplied may result in internal damage to the TV set or cause it to fall, etc.

When transporting the TV set by hand, hold it as shown below. Do not put stress on the LCD panel and the frame around the screen.

To Sony Dealers and Contractors: Provide full attention to safety during the installation, periodic maintenance and examination of this product.

The TV system depends on your country/area selection/TV model. Analogue: B/G, D/K, I. Digital: DVB-T/DVB-C DVB-T2*1. Satellite*1: DVB-S/DVB-S2.

The supported video input formats for the HDMI IN 1/2/3/4 are: 4096 × 2160p (50, 60 Hz)*2*3, 4096 × 2160p (24 Hz)*2, 3840 × 2160p (50, 60 Hz)*3, 3840 × 2160p (24, 25, 30 Hz), 1080p (30, 50, 60 Hz), 1080/24p, 1080i (50, 60 Hz), 720p (30, 50, 60 Hz), 720/24p, 576p, 576i, 480p, 480i, PC Formats*4.

Connect your audio system to the HDMI IN 3 to route TV audio to your audio system. An audio system that supports HDMI ARC can send video to the TV, and receive audio from the TV via the same HDMI cable. If your audio system does not support HDMI ARC, an additional connection with DIGITAL AUDIO OUT (OPTICAL) is necessary.

The supported audio formats are: 5.1 channel linear PCM: 32/44.1/48/88.2/96/176.4/192 kHz 16/20/24 bits, Dolby Digital, Dolby Digital Plus and DTS. ARC (Audio Return Channel) (HDMI IN 3 only) (Two channel linear PCM: 48 kHz 16 bits, Dolby Digital, Dolby Digital Plus, DTS).

When transporting the TV set for repairs or when moving, pack it using the original carton and packing material.

Before transporting the TV set, disconnect all cables. Two or three people are needed to transport a large TV set.

When lifting or moving the TV set, hold it firmly from the bottom.

Install the TV so that the TV’s Table-Top Stand does not protrude out from the TV stand (not supplied). If the Table-Top Stand protrudes out from the TV stand, it may cause TV set to topple over, fall down, and cause personal injury or damage to the TV.

Be sure to use the screws supplied with the Wall-Mount Bracket when attaching the Wall-Mount Bracket to the TV set. The supplied screws are designed as indicated by illustration when measured from the attaching surface of the Wall-Mount Bracket. The diameter and length of the screws differ depending on the Wall-Mount Bracket model.

Only qualified service personnel should carry out wall-mount installations.

For safety reasons, it is strongly recommended that you use Sony accessories, including: Wall-Mount Bracket SU-WL450.

When installing the Wall-Mount Bracket, also refer to the Operating Instructions and Installation Guide supplied with the Wall-Mount Bracket. Be sure to store the removed screws in a safe place, keeping them away from children. Place the TV with its screen facing down on a level and stable surface covered with a thick and soft cloth when removing the Table-Top Stand from the TV to prevent damaging the surface of the LCD display.

The torque specification for the cord (not supplied) is 1.5 N·m {15 kgf·cm}.

The recommended screw size is M6 screws, 8 mm – 12 mm long.

Labels for the TV Model No., Production Date (year/month) and Power Supply rating are located on the rear of the TV or package. For models with supplied mains adaptor: Labels for mains adaptor Model No. and Serial No. are located at the bottom of mains adaptor.

To enjoy high quality 4K 50p/60p contents, connect a Premium High Speed HDMI cable to the HDMI IN 2/3 and set the [HDMI signal format] to [Enhanced format]. For details of supported formats, refer to the “Specifications” in this manual.

Repeat the previous step and remove the other side of the Table-Top Stand. Note: Three or more people are required to detach the Table-Top Stand. Be careful not to use excessive force while detaching the Table-Top Stand from the TV as it may cause the TV set to fall resulting in personal injury or physical damage to the TV. Take care when handling the Table-Top Stand to prevent damage to the TV. Be careful when lifting the TV as the Table-Top Stand is detached, the Table-Top Stand may topple over and cause personal injury. Take care when removing the Table-Top Stand from the TV to prevent it from falling over and damaging the surface that the TV is sitting on.

Remove one side of the Table-Top Stand at a time. Firmly hold the Table-Top Stand securely with both hands while the other people lift up the TV.

Repeat the previous step and remove the other side of the Table-Top Stand. Note: Three or more people are required to detach the Table-Top Stand. Be careful not to use excessive force while detaching the Table-Top Stand from the TV as it may cause the TV set to fall resulting in personal injury or physical damage to the TV. Take care when handling the Table-Top Stand to prevent damage to the TV. Be careful when lifting the TV as the Table-Top Stand is detached, the Table-Top Stand may topple over and cause personal injury. Take care when removing the Table-Top Stand from the TV to prevent it from falling over and damaging the surface that the TV is sitting on.

The recommended screw size is M6 screws, 8 mm – 12 mm long.

The required torque for the cord (not supplied) is 1.5 N·m {15 kgf·cm}.

The dimensions (Approx.) (w × h × d) with Table-Top Stand for the SONY BRAVIA KD-75XG80xx are 168.6 × 103.4 × 40.2 cm.

The dimensions (Approx.) (w × h × d) without Table-Top Stand for the SONY BRAVIA KD-75XG80xx are 168.6 × 97.0 × 8.0 cm.

The approximate mass (Approx.) with Table-Top Stand for the SONY BRAVIA KD-75XG80xx is 32.5 kg.

The approximate mass (Approx.) without Table-Top Stand for the SONY BRAVIA KD-75XG80xx is 30.7 kg.

The annual energy consumption for the SONY BRAVIA KD-75XG80xx is 254 kWh per year.

The power consumption for the SONY BRAVIA KD-75XG8096 in [Vivid] mode is 295 W.

The TV system depends on your country/area selection/TV model. Analogue: B/G, D/K, I. Digital: DVB-T/DVB-C DVB-T2*1. Satellite*1: DVB-S/DVB-S2.

The color system is PAL/SECAM/NTSC3.58 (Video only)/NTSC4.43 (Video only).

The channel coverage depends on your country/area selection/TV model. Analogue: UHF/VHF/Cable. Digital: UHF/VHF/Cable. Satellite*1: IF Frequency 950-2,150 MHz.

The sound output is 10 W + 10 W.

The wireless technology protocol is IEEE802.11ac/a/b/g/n. Bluetooth Version 4.1.

The specifications for Wireless LAN (IEEE 802.11ac/a/b/g/n) are:

The specifications for Bluetooth frequency range and output power for the SONY BRAVIA KD-75XG80xx (using RMF-TX310E/TX220E) are:

The specifications for Bluetooth frequency range and output power for the SONY BRAVIA KD-75XG80xx (using RMF-TX310E/TX220E model for Bluetooth) are:

The LAN connector is 10BASE-T/100BASE-TX connector (Depending on the operating environment of the network, connection speed may differ. The communication rate and quality are not guaranteed.).

The DC IN is 19.5 V (models with supplied mains adaptor only).

The optional accessories include: Wall-Mount Bracket: SU-WL450.

The Energy Efficiency Class for the SONY BRAVIA KD-75XG80xx is A.

The screen size (measured diagonally) (Approx.) for the SONY BRAVIA KD-75XG80xx is 189.3 cm / 75 inches.