Free English MOXA NPORT 5650-8-S-SC (02) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD MOXA NPORT 5650-8-S-SC (02) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What should be included in the MOXA NPORT 5650-8-S-SC package?
The MOXA NPORT 5650-8-S-SC package should contain the following items:
• 1 NPort 5600 Series serial device server
• Power cord (AC models only)
• 1 DIN-rail/wall-mounting kit: WK-45-01
• NPort 5600 Quick Installation Guide
Please notify your sales representative if any of the above items are missing or damaged.
What optional accessories are available for the MOXA NPORT 5650-8-S-SC?
The following optional accessories are available:
• CBL-RJ45M9-150: 8-pin RJ45 to DB9 male cable, 150 cm
• CBL-RJ45F9-150: 8-pin RJ45 to DB9 female cable, 150 cm
• CBL-RJ45M25-150: 8-pin RJ45 to DB25 male cable, 150 cm
• CBL-RJ45F25-150: 8-pin RJ45 to DB25 female cable, 150 cm
Do wide temperature models of the MOXA NPORT 5650-8-S-SC come with LCM display panels?
No, the wide temperature model does not come with LCM display panels or push buttons. All LCM descriptions apply only to standard temperature models.
How do I load factory defaults on my MOXA NPORT 5650-8-S-SC?
To load factory defaults, use a pointed object to press the Reset button continuously for 5 seconds. Release the button after the Ready LED stops blinking.
What do the front panel LED indicators on the MOXA NPORT 5650-8-S-SC mean?
| Name | Color | Function |
|---|---|---|
| Ready | Off | Power is off, or power error condition exists. |
| Red | Steady on: Power is on and the NPort is booting up. | |
| Blinking: Indicates an IP conflict, or DHCP or BOOTP server did not respond properly. | ||
| Green | Steady on: Power is on and the NPort is functioning normally. Blinking: The NPort has been located by NPort Administrator’s Location function. |
|
| 1 to 16 | Orange | Serial port is receiving data. |
| Green | Serial port is transmitting data. | |
| Off | No data is being transmitted or received through the serial port. |
What information is shown on the LCM display panel of the MOXA NPORT 5650-8-S-SC?
If the device is working properly, the LCM panel will display a green color. After the red Ready LED turns green, you will see a display similar to:
NP5610-16 38
192.168.127.254
This is where:
• NP5610-16 is the NPort’s name
• 38 is the NPort’s local sequence number
• 192.168.127.254 is the NPort’s IP address
How do I operate the LCM panel buttons on my MOXA NPORT 5650-8-S-SC?
There are four buttons on the front panel used to operate the LCM panel. Going from left to right, the buttons are:
| Button | Action |
|---|---|
| MENU | Activates the main menu, or returns to a lower level. |
| ^ | Scrolls up through a list of items shown on the LCM panel’s second line. |
| v | Scrolls down through a list of items shown on the LCM panel’s second line. |
| SEL | Selects the option listed on the LCM panel’s second line. |
What do the link indicator LEDs on the rear panel of the MOXA NPORT 5650-8-S-SC fiber model indicate?
The rear panels of the NPort 5650 fiber models have a link indicator with the following functions:
| LED Name | LED Color | LED Function |
|---|---|---|
| Link | Off | Fiber disconnected. |
| Green | Fiber connected, data not transmitting. | |
| Blinking | Fiber connected, data is transmitting. |
What are the hardware installation steps for the MOXA NPORT 5650-8-S-SC?
STEP 1: Attach Power Adapter
After removing the device from the box, the first step is to attach the power adapter.
STEP 2: Connect Power
• AC Power: Connect the 100-240 VAC power cord to the AC connector. The “Ready” LED will show a solid red color until the system is ready, at which time it will change to a green color.
• DC Power: Connect the VDC power cord to the DC connector. For a model like the NPort 5610-8-48V, loosen the screws on the V+ and V- terminals of the terminal block. Connect the power cord’s 48 VDC or -48 VDC wire to the V+ terminal, and the power cord’s DC Power Ground wire to the V- terminal, then tighten the screws. The “Ready” LED will show a solid red color until the system is ready, at which time it will change to a green color.
Grounding the NPort 5600 VDC:
Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the ground screw to the grounding surface prior to connecting devices. The Shielded Ground (SG) contact is the second contact from the right of the 5-pin power terminal block connector. Connect the SG wire to the Earth ground.
STEP 3: Connect to Network
Use a standard straight-through Ethernet cable to connect to a hub or switch. When setting up or testing, you might find it convenient to connect directly to your computer’s Ethernet port using a cross-over Ethernet cable.
STEP 4: Connect to Serial Device
Connect the NPort 5600’s serial port to a serial device.
Placement Options:
You can place the NPort 5600 on a desktop or other horizontal surface.
What is the default IP address of the MOXA NPORT 5650-8-S-SC and how do I start the configuration?
For the NPort’s configuration, the default IP address is:
LAN: Static; IP = 192.168.127.254; netmask = 255.255.255.0
You may log in with the password moxa to change any settings to meet your network topology (e.g., IP address) or serial device (e.g., serial parameters). For first-time use, click the Wizard in the left navigation panel. The wizard will prompt you to configure the IP address, SSID, and security mode. For other settings, use the factory defaults or modify the settings for your application.
How can I find the IP address of my MOXA NPORT 5650-8-S-SC if I’ve forgotten it?
If you have forgotten the NPort’s IP address, use the Device Search Utility (DSU) from your PC to locate the NPort. After searching the LAN for NPort units, the DSU will display the IP address of each unit.
What are the general steps for software installation for the MOXA NPORT 5650-8-S-SC?
Follow these steps for software installation:
• Download the NPort Windows Driver Manager and install it as the driver to run with Real COM mode of the NPort Series.
• Execute NPort Windows Driver Manager; then map the virtual COM ports on your Windows platform.
• You may refer to the pin assignment section to loop back pin 4 and pin 5 for the RS-232 interface to carry out a self test on the device.
• Use HyperTerminal or a similar program (you may download Moxa’s program, called PComm Lite) to test whether the device is good or not.
What are the serial port pin assignments for the MOXA NPORT 5650-8-S-SC?
| Pin | RS-232 | RS-422/RS-485-4W | RS-485-2W |
|---|---|---|---|
| 1 | DSR | – | – |
| 2 | RTS | TxD+ | – |
| 3 | GND | GND | GND |
| 4 | TxD | TxD- | – |
| 5 | RxD | RxD+ | Data+ |
| 6 | DCD | RxD- | Data- |
| 7 | CTS | – | – |
| 8 | DTR | – | – |
How should I wire the serial cables for the MOXA NPORT 5650-8-S-SC for RS-232 communication?
| NPort 5650 (RJ45 Port) | DB9-M | DB9-F | DB-25-M | DB-25-F | Serial Device | ||
|---|---|---|---|---|---|---|---|
| DSR | 1 | 6 | 4 | 6 | 20 | DTR | |
| RTS | 2 | 7 | 8 | 4 | 5 | CTS | |
| GND | 3 | 5 | 5 | 7 | 7 | GND | |
| TxD | 4 | 3 | 2 | 2 | 3 | RxD | |
| RxD | 5 | 2 | 3 | 3 | 2 | TxD | |
| DCD | 6 | 1 | 1 | 8 | 8 | DCD | |
| CTS | 7 | 8 | 7 | 5 | 4 | RTS | |
| DTR | 8 | 4 | 6 | 20 | 6 | DSR | |
How should I wire the serial cables for the MOXA NPORT 5650-8-S-SC for 2-wire RS-485 communication?
| NPort 5650 (RJ45 Port) | DB9-M | DB9-F | DB-25-M | DB-25-F | Serial Device | ||
|---|---|---|---|---|---|---|---|
| GND | 3 | 5 | 5 | 7 | 7 | GND | |
| Data+ | 5 | 2 | 3 | 3 | 2 | Data+ | |
| Data- | 6 | 1 | 1 | 8 | 8 | Data- | |
How should I wire the serial cables for the MOXA NPORT 5650-8-S-SC for RS-422/4-wire RS-485 communication?
| NPort 5650 (RJ45 Port) | DB9-M | DB9-F | DB-25-M | DB-25-F | Serial Device | ||
|---|---|---|---|---|---|---|---|
| TxD+ | 2 | 7 | 8 | 4 | 5 | RxD+ | |
| GND | 3 | 5 | 5 | 7 | 7 | GND | |
| TxD- | 4 | 3 | 2 | 2 | 3 | RxD- | |
| RxD+ | 5 | 2 | 3 | 3 | 2 | TxD+ | |
| RxD- | 6 | 1 | 1 | 8 | 8 | TxD- | |
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD MOXA NPORT 5650-8-S-SC (02) PDF DOCUMENT