Free English MOXA NPORT 5630-8 (03) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD MOXA NPORT 5630-8 (03) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What items are included in the package for the MOXA NPORT 5630-8?
The MOXA NPORT 5630-8 package should contain the following items:
• 1 NPort 5600 Series serial device server
• Power cord (AC models only)
• 1 DIN-rail/wall-mounting kit: WK-45-01
• NPort 5600 Quick Installation Guide
What optional accessories are available for the MOXA NPORT 5630-8?
The following optional accessories are available:
• CBL-RJ45M9-150: 8-pin RJ45 to DB9 male cable, 150 cm
• CBL-RJ45F9-150: 8-pin RJ45 to DB9 female cable, 150 cm
• CBL-RJ45M25-150: 8-pin RJ45 to DB25 male cable, 150 cm
• CBL-RJ45F25-150: 8-pin RJ45 to DB25 female cable, 150 cm
How do I load the factory defaults on the MOXA NPORT 5630-8?
To load factory defaults, press the Reset button continuously for 5 seconds. Use a pointed object to press the reset button. Release the button after the Ready LED stops blinking.
What do the front panel LED indicators on the MOXA NPORT 5630-8 signify?
| Name | Color | Function |
|---|---|---|
| Ready | Off | Power is off, or power error condition exists. |
| Red | Steady on: Power is on and the NPort is booting up. Blinking: Indicates an IP conflict, or DHCP or BOOTP server did not respond properly. |
|
| Green | Steady on: Power is on and the NPort is functioning normally. Blinking: The NPort has been located by NPort Administrator’s Location function. |
|
| 1 to 16 | Orange | Serial port is receiving data. |
| Green | Serial port is transmitting data. | |
| Off | No data is being transmitted or received through the serial port. |
How do I operate the LCM panel on the MOXA NPORT 5630-8?
There are four buttons on the front panel used to operate the LCM panel. Going from left to right, the buttons and their functions are:
| Button | Action |
|---|---|
| MENU | Activates the main menu, or returns to a lower level. |
| ^ | Scrolls up through a list of items shown on the LCM panel’s second line. |
| v | Scrolls down through a list of items shown on the LCM panel’s second line. |
| SEL | Selects the option listed on the LCM panel’s second line. |
Note: Wide temperature models do not come with LCM display panels or push buttons. The LCM descriptions apply only to standard temperature models.
What are the steps for hardware installation of the MOXA NPORT 5630-8?
STEP 1: Attach the Power Adapter
After removing the MOXA NPORT 5630-8 from the box, the first thing you should do is attach the power adapter.
STEP 2: Connecting the Power
AC Power: Connect the 100-240 VAC power cord to the AC connector. The “Ready” LED will show a solid red color until the system is ready, at which time it will change to a green color.
DC Power: Connect the power cord to the DC connector. For a model like the NPort 5610-8-48V, loosen the screws on the V+ and V- terminals. Connect the power cord’s 48 VDC or -48 VDC wire to the V+ terminal, and the DC Power Ground wire to the V- terminal. Then tighten the terminal block screws. The “Ready” LED will show a solid red color until the system is ready, at which time it will change to a green color.
Grounding the DC model: Grounding and wire routing help limit the effects of noise from electromagnetic interference (EMI). Run the ground connection from the ground screw to the grounding surface before connecting devices. For models like the NPort 5610-8-48V, the Shielded Ground (SG) contact is the second contact from the right of the 5-pin power terminal block connector. Connect the SG wire to the Earth ground.
STEP 3: Connect to a Network
Use a standard straight-through Ethernet cable to connect to a hub or switch. When setting up or testing, you can connect directly to your computer’s Ethernet port using a cross-over Ethernet cable.
STEP 4: Connect to a Serial Device
Connect the MOXA NPORT 5630-8’s serial port to a serial device.
Placement Options: You can place the device on a desktop or other horizontal surface.
What is the default IP address for the MOXA NPORT 5630-8 and how do I install the software?
For the MOXA NPORT 5630-8’s configuration, the default IP address is:
• LAN: Static
• IP: 192.168.127.254
• Netmask: 255.255.255.0
If you have forgotten the IP address, use the Device Search Utility (DSU) from your PC to locate the device. After searching the LAN, the DSU will display the IP address of each unit.
You may log in with the password moxa to change settings. For first-time use, click the Wizard in the left navigation panel to configure the IP address, SSID, and security mode.
For software installation, follow these steps:
1. Download the NPort Windows Driver Manager and install it as the driver to run with Real COM mode of the NPort Series.
2. Execute NPort Windows Driver Manager; then map the virtual COM ports on your Windows platform.
3. You may refer to the pin assignment section to loop back pin 4 and pin 5 for the RS-232 interface to carry out a self-test on the device.
4. Use HyperTerminal or a similar program (such as Moxa’s PComm Lite) to test whether the device is good or not.
What are the serial port pin assignments for the MOXA NPORT 5630-8?
| Pin | RS-422/RS-485-4W | RS-485-2W |
|---|---|---|
| 1 | – | – |
| 2 | – | – |
| 3 | TxD+ | – |
| 4 | TxD- | – |
| 5 | RxD- | Data- |
| 6 | RxD+ | Data+ |
| 7 | GND | GND |
| 8 | – | – |
How should I wire the serial cables for the MOXA NPORT 5630-8 for 2-wire RS-485 operation?
The following tables show the connections from the RJ45 port on the MOXA NPORT 5630-8 to various serial connectors for 2-wire RS-485 communication.
RJ45 to DB9 Male
| NPort 5630 Signal (RJ45 Pin) | DB9-M Pin |
|---|---|
| Data- (5) | 2 |
| Data+ (6) | 1 |
| GND (7) | 8 |
RJ45 to DB9 Female
| NPort 5630 Signal (RJ45 Pin) | DB9-F Pin |
|---|---|
| Data- (5) | 3 |
| Data+ (6) | 1 |
| GND (7) | 7 |
RJ45 to DB25 Male
| NPort 5630 Signal (RJ45 Pin) | DB25-M Pin |
|---|---|
| Data- (5) | 3 |
| Data+ (6) | 8 |
| GND (7) | 5 |
RJ45 to DB25 Female
| NPort 5630 Signal (RJ45 Pin) | DB25-F Pin |
|---|---|
| Data- (5) | 2 |
| Data+ (6) | 8 |
| GND (7) | 4 |
How should I wire the serial cables for the MOXA NPORT 5630-8 for RS-422/4-wire RS-485 operation?
The following tables show the connections from the RJ45 port on the MOXA NPORT 5630-8 to various serial connectors for RS-422/4-wire RS-485 communication. The serial device signals are listed for reference.
RJ45 to DB9 Male
| NPort 5630 Signal (RJ45 Pin) | DB9-M Pin | Serial Device Signal |
|---|---|---|
| TxD+ (3) | 5 | RxD+ |
| TxD- (4) | 3 | RxD- |
| RxD- (5) | 2 | TxD- |
| RxD+ (6) | 1 | TxD+ |
| GND (7) | 8 | GND |
RJ45 to DB9 Female
| NPort 5630 Signal (RJ45 Pin) | DB9-F Pin | Serial Device Signal |
|---|---|---|
| TxD+ (3) | 5 | RxD+ |
| TxD- (4) | 2 | RxD- |
| RxD- (5) | 3 | TxD- |
| RxD+ (6) | 1 | TxD+ |
| GND (7) | 7 | GND |
RJ45 to DB25 Male
| NPort 5630 Signal (RJ45 Pin) | DB25-M Pin | Serial Device Signal |
|---|---|---|
| TxD+ (3) | 7 | RxD+ |
| TxD- (4) | 2 | RxD- |
| RxD- (5) | 3 | TxD- |
| RxD+ (6) | 8 | TxD+ |
| GND (7) | 5 | GND |
RJ45 to DB25 Female
| NPort 5630 Signal (RJ45 Pin) | DB25-F Pin | Serial Device Signal |
|---|---|---|
| TxD+ (3) | 7 | RxD+ |
| TxD- (4) | 3 | RxD- |
| RxD- (5) | 2 | TxD- |
| RxD+ (6) | 8 | TxD+ |
| GND (7) | 4 | GND |
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD MOXA NPORT 5630-8 (03) PDF DOCUMENT