Free English MOXA NPORT 5650-16 (02) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD MOXA NPORT 5650-16 (02) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What items are included in the MOXA NPORT 5650-16 package?
The MOXA NPORT 5650-16 package should contain the following items:
• 1 NPort 5600 Series serial device server
• Power cord (AC models only)
• 1 DIN-rail/wall-mounting kit: WK-45-01
• NPort 5600 Quick Installation Guide
What optional accessories are available for the MOXA NPORT 5650-16?
The following optional accessories are available:
• CBL-RJ45M9-150: 8-pin RJ45 to DB9 male cable, 150 cm
• CBL-RJ45F9-150: 8-pin RJ45 to DB9 female cable, 150 cm
• CBL-RJ45M25-150: 8-pin RJ45 to DB25 male cable, 150 cm
• CBL-RJ45F25-150: 8-pin RJ45 to DB25 female cable, 150 cm
How do I reset the MOXA NPORT 5650-16 to its factory default settings?
To load factory defaults, use a pointed object to press the Reset button continuously for 5 seconds. You can release the button after the Ready LED stops blinking.
What do the front panel LED indicators on the MOXA NPORT 5650-16 mean?
| Name | Color | Function |
|---|---|---|
| Ready | Off | Power is off, or power error condition exists. |
| Red | Steady on: Power is on and the NPort is booting up. Blinking: Indicates an IP conflict, or DHCP or BOOTP server did not respond properly. |
|
| Green | Steady on: Power is on and the NPort is functioning normally. Blinking: The NPort has been located by NPort Administrator’s Location function. |
|
| 1 to 16 | Orange | Serial port is receiving data. |
| Green | Serial port is transmitting data. | |
| Off | No data is being transmitted or received through the serial port. |
What information is shown on the LCM display panel of the MOXA NPORT 5650-16?
When the MOXA NPORT 5650-16 is working properly, the LCM panel will display a green color and show information similar to the following example:
First Line: NP5610-16 38
Second Line: 192.168.127.254
This display shows:
• The NPort’s name (e.g., NP5610-16)
• The NPort’s local sequence number (e.g., 38)
• The NPort’s IP address (e.g., 192.168.127.254)
NOTE: The wide temperature model does not come with an LCM display panel or push buttons.
How do I operate the LCM panel on the MOXA NPORT 5650-16?
There are four buttons on the front panel used to operate the LCM panel. From left to right, their functions are as follows:
| Button | Action |
|---|---|
| MENU | Activates the main menu, or returns to a lower level. |
| ^ (Up Arrow) | Scrolls up through a list of items shown on the LCM panel’s second line. |
| v (Down Arrow) | Scrolls down through a list of items shown on the LCM panel’s second line. |
| SEL | Selects the option listed on the LCM panel’s second line. |
What do the link indicators on the rear panel of a MOXA NPORT 5650-16 fiber model signify?
The link indicators on the rear panel of the NPort 5650 fiber models have the following functions:
| LED Name | LED Color | LED Function |
|---|---|---|
| Link | Off | Fiber disconnected. |
| Green | Fiber connected, data not transmitting. | |
| Blinking | Fiber connected, data is transmitting. |
What are the steps for hardware installation of the MOXA NPORT 5650-16?
Follow these steps to install the MOXA NPORT 5650-16:
STEP 1: Attach Power
After removing the NPort 5600 from the box, attach the power adapter.
STEP 2: Connect Power
Connect the power based on your model type:
• AC Power: Connect the NPort’s 100-240 VAC power cord to the AC connector. The “Ready” LED will show a solid red color until the system is ready, at which time it will change to a green color.
• DC Power: Connect the power cord to the DC connector. For example, on a NPort 5610-8-48V, loosen the screws on the V+ and V- terminals. Connect the power cord’s 48 VDC or -48 VDC wire to the V+ terminal and the DC Power Ground wire to the V- terminal, then tighten the screws. The “Ready” LED will turn from solid red to green when the system is ready.
• Grounding (DC Models): To limit the effects of electromagnetic interference (EMI), run a ground connection from the ground screw to a grounding surface. On a model like the NPort 5610-8-48V, the Shielded Ground (SG) contact is the second from the right on the 5-pin terminal block. Connect the SG wire to the Earth ground.
STEP 3: Connect to Network
Use a standard straight-through Ethernet cable to connect the NPort 5600 to a hub or switch. If you are connecting directly to a computer’s Ethernet port for setup or testing, use a cross-over Ethernet cable.
STEP 4: Connect Serial Device
Connect the NPort 5600’s serial port to your serial device.
The device can be placed on a desktop or another horizontal surface.
What is the default IP address of the MOXA NPORT 5650-16?
The default network configuration for the NPort is:
• LAN: Static
• IP Address: 192.168.127.254
• Netmask: 255.255.255.0
What should I do if I forget the IP address of my MOXA NPORT 5650-16?
If you have forgotten the NPort’s IP address, use the Device Search Utility (DSU) from your PC to locate the NPort. After searching the LAN for NPort units, the DSU will display the IP address of each unit found.
How do I install the necessary software for the MOXA NPORT 5650-16?
You may log in with the password moxa to change settings. For first-time use, click the Wizard to configure the IP address, SSID, and security mode. For software installation, follow these steps:
1. Download the NPort Windows Driver Manager and install it as the driver to run with Real COM mode of the NPort Series.
2. Execute NPort Windows Driver Manager; then map the virtual COM ports on your Windows platform.
3. You may refer to the pin assignment section to loop back pin 4 (TxD) and pin 5 (RxD) for the RS-232 interface to carry out a self-test on the device.
4. Use HyperTerminal or a similar program (such as PComm Lite) to test whether the device is functioning correctly.
What are the serial port pin assignments for the MOXA NPORT 5650-16?
| Pin | RS-232 | RS-422/RS-485-4W | RS-485-2W |
|---|---|---|---|
| 1 | DSR | – | – |
| 2 | RTS | TxD+ | – |
| 3 | GND | GND | GND |
| 4 | TxD | TxD- | – |
| 5 | RxD | RxD+ | Data+ |
| 6 | DCD | RxD- | Data- |
| 7 | CTS | – | – |
| 8 | DTR | – | – |
What are the serial port pin assignments for an NPort 5610 series device?
| Pin | RS-232 |
|---|---|
| 1 | DSR (in) |
| 2 | RTS(out) |
| 3 | GND |
| 4 | TxD(out) |
| 5 | RxD(in) |
| 6 | DCD(in) |
| 7 | CTS(in) |
| 8 | DTR(out) |
What are the serial port pin assignments for an NPort 5630 series device?
| Pin | RS-422/RS-485-4W | RS-485-2W |
|---|---|---|
| 1 | – | – |
| 2 | – | – |
| 3 | TxD+ | – |
| 4 | TxD- | – |
| 5 | RxD- | Data- |
| 6 | RxD+ | Data+ |
| 7 | GND | GND |
| 8 | – | – |
How should I wire an RS-232 serial cable for the MOXA NPORT 5650-16?
The following table shows the RJ45 (NPort side) to DB9 and DB25 (Serial Device side) pin mappings for an RS-232 connection.
| NPort 5610/5650 RJ45 Pin |
Signal | DB9-M Pin | DB9-F Pin | DB-25-M Pin | DB-25-F Pin | Signal |
|---|---|---|---|---|---|---|
| 1 | DSR | 6 | 4 | 6 | 20 | DTR |
| 2 | RTS | 7 | 8 | 4 | 5 | CTS |
| 3 | GND | 5 | 5 | 7 | 7 | GND |
| 4 | TxD | 3 | 2 | 2 | 3 | RxD |
| 5 | RxD | 2 | 3 | 3 | 2 | TxD |
| 6 | DCD | 1 | 1 | 8 | 8 | DCD |
| 7 | CTS | 8 | 7 | 5 | 4 | RTS |
| 8 | DTR | 4 | 6 | 20 | 6 | DSR |
How should I wire a 2-wire RS-485 serial cable for the MOXA NPORT 5650-16?
The following table shows the RJ45 (NPort side) to DB9 and DB25 (Serial Device side) pin mappings for a 2-wire RS-485 connection.
| NPort 5650 RJ45 Pin |
Signal | DB9-M Pin | DB9-F Pin | DB-25-M Pin | DB-25-F Pin | Signal |
|---|---|---|---|---|---|---|
| 3 | GND | 5 | 5 | 7 | 7 | GND |
| 5 | Data+ | 2 | 3 | 3 | 2 | Data+ |
| 6 | Data- | 1 | 1 | 8 | 8 | Data- |
How should I wire a 4-wire RS-485/RS-422 serial cable for the MOXA NPORT 5650-16?
The following table shows the RJ45 (NPort side) to DB9 and DB25 (Serial Device side) pin mappings for a 4-wire RS-485/RS-422 connection.
| NPort 5650 RJ45 Pin |
Signal | DB9-M Pin | DB9-F Pin | DB-25-M Pin | DB-25-F Pin | Signal |
|---|---|---|---|---|---|---|
| 2 | TxD+ | 7 | 8 | 4 | 5 | RxD+ |
| 3 | GND | 5 | 5 | 7 | 7 | GND |
| 4 | TxD- | 3 | 2 | 2 | 3 | RxD- |
| 5 | RxD+ | 2 | 3 | 3 | 2 | TxD+ |
| 6 | RxD- | 1 | 1 | 8 | 8 | TxD- |
How should I wire a 2-wire RS-485 serial cable for an NPort 5630 series device?
The following table shows the RJ45 (NPort side) to DB9 and DB25 (Serial Device side) pin mappings for a 2-wire RS-485 connection.
| NPort 5630 RJ45 Pin |
Signal | DB9-M Pin | DB9-F Pin | DB-25-M Pin | DB-25-F Pin | Signal |
|---|---|---|---|---|---|---|
| 5 | Data- | 2 | 3 | 3 | 2 | Data- |
| 6 | Data+ | 1 | 1 | 8 | 8 | Data+ |
| 7 | GND | 8 | 7 | 5 | 4 | GND |
How should I wire a 4-wire RS-485/RS-422 serial cable for an NPort 5630 series device?
The following table shows the RJ45 (NPort side) to DB9 and DB25 (Serial Device side) pin mappings for a 4-wire RS-485/RS-422 connection.
| NPort 5630 RJ45 Pin |
Signal | DB9-M Pin | DB9-F Pin | DB-25-M Pin | DB-25-F Pin | Signal |
|---|---|---|---|---|---|---|
| 3 | TxD+ | 5 | 5 | 7 | 7 | RxD+ |
| 4 | TxD- | 3 | 2 | 2 | 3 | RxD- |
| 5 | RxD- | 2 | 3 | 3 | 2 | TxD- |
| 6 | RxD+ | 1 | 1 | 8 | 8 | TxD+ |
| 7 | GND | 8 | 7 | 5 | 4 | GND |
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD MOXA NPORT 5650-16 (02) PDF DOCUMENT