AUTOMATIONDIRECT C-MORE EA9-T10WCL (01) PDF DOCUMENT

You should inspect all equipment for completeness. The package for the AUTOMATIONDIRECT C-MORE EA9-T10WCL should contain the following items:

• C-more Panel

• Quick Start Guide

• Cutout Template*

• Gasket

• DC power connector

• Mounting Clips

• Logo Label*

*Not included with EA9-T7CL-R and EA9-T7CL.

If anything is missing or damaged, you should immediately call the AutomationDirect returns department.

To provide DC power to the AUTOMATIONDIRECT C-MORE EA9-T10WCL, follow these steps:

1. Wire a dedicated 12-24 VDC power source to the DC connector on the rear of the C-more touch panel.

2. Include wiring for the ground terminal to a proper equipment ground.

3. Turn on the power source and check the LED status indicators on the front and rear of the panel for proper indication.

Use 60 / 75°C copper conductors only, with a wire gauge of 12 – 24 AWG.

The recommended DC supply fuse depends on the panel size:

The tightening torque specifications for the DC power connector are as follows:

To power the panel with an AC source, you must use the optional C-more AC/DC Power Adapter (p/n EA-AC). Follow these steps:

1. Install the C-more AC/DC Power Adapter to the rear of the touch panel.

2. Wire an AC voltage source of 100-240 VAC, 50/60 Hz, to its AC connector.

3. It is recommended to use a 3.0A time delay AC supply fuse (ADC p/n: MDL3).

4. Turn on the power source and check the LED status indicators for proper indication.

The tightening torque specifications for the EA-AC adapter are as follows:

The CPU Status LED (Green, Orange & Red) indicates the operational state of the panel’s CPU. The meanings are as follows:

The green Power LED on the front of the panel indicates the power status:

To minimize the risk of potential safety problems, you should follow all applicable local and national codes that regulate the installation and operation of your equipment. It is your responsibility to determine which codes should be followed and to verify that the equipment, installation, and operation are in compliance with the latest revision of these codes. Equipment damage or serious injury to personnel can result from the failure to follow all applicable codes and standards. If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.

The cutout dimensions for the AUTOMATIONDIRECT C-MORE EA9-T10WCL are as follows:

When installing the AUTOMATIONDIRECT C-MORE EA9-T10WCL in an enclosure or cabinet, the mounting clearances shall be a minimum of 4 inches from the top, bottom and sides, and 1.72 inches from the rear.

The requirements for mounting the AUTOMATIONDIRECT C-MORE EA9-T10WCL are as follows:

The display screen should be cleaned periodically by wiping it with a lint-free damp cloth using a mild soap solution. Use a dry or slightly dampened cloth to wipe any dirt from the labels on the back of the panel. Dry all surfaces with a lint-free cloth. Do not clean with ammonia-based products which are solvents and will damage the face of the panel and the labels.

The touchscreen is designed to respond to a single touch. If it is touched at multiple points at the same time, an unexpected object may be activated.

The UL ratings for the AUTOMATIONDIRECT C-MORE EA9-T10WCL are:

• Input Rating: 12-24 VDC, Class 2, SELV or LEC, Maximum 17.0W

• Terminal connecting wire size: 12-24 AWG

• Connecting torque: 71 – 85 oz-in (5-7 lbf-in) (0.5 – 0.6 Nm)

• Surrounding Air Temperature rating: 0 to 50°C (32 to 122°F)

• For use in Pollution Degree 2 environment

• All interface ports are intended to be directly connected to an isolated secondary circuit

• For use on a flat surface of a type 4X Indoor Use Only enclosure