VTECH VM305 (01) PDF Document

The package for the VTECH VM305 contains the following items:

• 1 baby unit

• 1 parent unit

• 2 power adapters

To connect the VTECH VM305 baby monitor, please follow these steps:

1. Make sure the baby unit is switched off.

2. Connect the power adapter to the baby unit and a power supply.

3. Slide the ON/OFF switch to ON to turn on the baby unit. The power LED light will turn on.

To connect the parent unit:

1. Connect the power adapter to the parent unit and a power supply.

Please note the following:

• Use only the power adapters supplied with this product.

• Make sure the baby unit is not controlled by a wall switch.

• The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.

The VTECH VM305 parent unit has the following features:

• POWER light: On when the parent unit is turned on.

• ON/OFF LED light:
• On when the baby unit is turned on and is paired to the parent unit.
• Flashes when the baby unit is not being viewed, or when the link to the baby unit is lost.

• ON/OFF switch: Slide to turn on or off the parent unit.

• VOL+: Press to raise the baby unit speaker volume. It also determines the talkback volume transmitted from the parent unit.

• VOL-: Press to lower the baby unit speaker volume. It also determines the talkback volume transmitted from the parent unit.

• PAIR: Press and hold to pair to the baby unit.

• Threaded socket: For use with a wall mount installation.

The VTECH VM305 baby unit is equipped with the following components:

• Light sensor

• Infrared LEDs

• Camera

• Microphone

• Speaker

• Antenna

• Power jack

• Temperature sensor

For the best performance of your VTECH VM305, please consider the following positioning tips:

• Keep the parent unit more than 1 meter (3 feet) away from the baby units to avoid audio feedback.

• Place the baby unit more than 1 meter (3 feet) away from your baby to avoid screeching noises.

• To avoid interference from other electronic devices, place your baby monitor far away from devices such as wireless routers, microwaves, cordless phones and computers.

• The default volume of your parent unit is level 4, and the maximum volume is level 7. If you experience a high-pitched screeching noise from your baby monitor while positioning:

• Make sure your baby and parent units are more than 1 meter (3 feet) apart, OR

• Turn down the volume of your parent unit.

You can pair a maximum of one baby unit to your parent unit. Each new baby unit (VM305) must be paired before use. Make sure you power on the parent unit before pairing.

To pair a new baby unit:

1. Press MENU when the parent unit is idle.

2. Press ◄ or ► to choose Pair/Unpair CAM, then press SELECT.

3. Press SELECT again to choose Pair CAM.

4. Press ▲ or ▼ to choose an empty baby unit slot, then press SELECT.

5. The screen will display: Press and hold the pair button of the cam. While the PAIR LED on the parent unit flashes, immediately press and hold the PAIR button on the baby unit. The PAIR LED light flashes quickly.

When the pairing is successful, the screen displays your newly paired baby unit in SINGLE-CAM mode. The LED light on the new baby unit remains on.

NOTES:

• If the pairing process fails, the screen displays Pairing failed! Try the pairing process again.

• Only one baby unit can be paired at a time.

Follow these steps to unpair a baby unit from your VTECH VM305 parent unit:

1. Make sure you power on the baby unit and the parent unit before starting the process.

2. Press MENU when the parent unit is idle.

3. Press ◄ or ► to choose Pair/Unpair CAM, then press SELECT.

4. Press ▲ or ▼ to choose Unpair CAM, then press SELECT.

5. Press ▲ or ▼ to select a desired baby unit, then press SELECT.

6. The screen displays Unpair CAM X, press the VOL◄ button to choose Yes, then press SELECT to confirm.

7. After the baby unit is unpaired from the parent unit, the screen displays Cam x Unpaired and then returns to the previous menu. To re-pair this baby unit, press SELECT to continue.

8. When pairing is successful, the screen displays CAM X is paired, and returns to the previous menu. When pairing is unsuccessful, the screen displays CAM X is paired, then Failed and the selected baby unit LED flashes slowly.

Before you begin, check for reception strength and camera angle before drilling the holes.

1. Place the wall mount bracket on a wall and then use a pencil to mark the top and the bottom holes as shown. Remove the wall mount bracket and drill two holes in the wall (7/32 inch drill bit).

2. If you drill the holes into a stud, go to step 3. If you drill the holes into an object other than a stud, insert the wall anchors into the holes. Tap gently on the ends with a hammer until the wall anchors are flush with the wall.

3. Align the wall mount bracket and screws with the holes in the wall as shown. Tighten the screw in the middle hole first, so that the wall mount bracket position is fixed. You can tighten the other screw in the top hole.

4. Place the baby unit on the wall mount bracket. Tighten the screw into the threaded socket at the bottom to secure the baby unit.

5. Insert the screws into the holes and tighten the screws until only 1/4 inch of the screws are exposed.

6. Place the baby unit on the wall mount bracket. Slide it down until it locks into place. Align the holes on the wall mount bracket with the screws on the wall, and slide the wall mount bracket down until it locks into place.

7. The default angle of the wall mount bracket is 90 degrees. You can maximize your baby unit’s viewing angles by tilting the wall mount bracket.

Hold the baby unit, and then rotate the knob in an anticlockwise direction. This will loosen the joint of the wall mount bracket. Tilt your baby unit up or down to adjust to your preferred angle. Then, rotate the knob in a clockwise direction to tighten the joint and secure the angle.

To keep the VTECH VM305 working well and looking good, follow these guidelines:

• The plastic housing of the baby units and parent unit may fade if exposed to direct sunlight for a long period of time.

• Clean your baby units and parent unit with a slightly damp cloth (do not use solvents).

• DO NOT clean with alcohol.

• Make sure the baby units and parent unit are dry before you connect them to the mains again.

When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1. Follow all warnings and instructions marked on the product.

2. Adult setup is required.

3. This product is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such.

4. This product is not intended for use as a medical monitor.

5. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower.

6. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product.

7. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.

8. This product should be operated only from the type of power source indicated on the marking label.

9. Do not allow anything to rest on the power cord. Do not install this product where the cord may be walked on or crimped.

10. Do not overload wall outlets or use an extension cord.

11. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.

12. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register.

13. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product.

14. To reduce the risk of electric shock, do not disassemble this product. There are no user-serviceable parts inside. Damage to the product should be referred to qualified service personnel.

15. You should test the sound reception every time you turn on the units or move one of the components.

16. Periodically examine all components for damage.

17. Be aware of possible loss of privacy while using public airwaves. Conversations may be picked up by other nursery monitors, cordless phones, scanners, etc.

18. Children should be supervised to ensure that they do not play with the product.

19. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Cautions:

• Use and store the product at a temperature between 0°C and 40°C.

• Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source.

• Make sure the baby unit and the adapter cord are always out of reach of the baby, at least 1 meter away from the baby or the crib, to avoid any possible strangulation hazard.

• Never place the baby unit inside the baby’s crib or playpen. Never cover the baby unit or parent unit with anything such as a towel or a blanket.

• Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones.