STORZ & BICKEL VEAZY (01) PDF Document

Please follow these basic rules when using your STORZ & BICKEL VEAZY:

• These Instructions for Use are an integral part of the Vaporizer and must be made available to the user.

• Read these instructions carefully and completely before operating the Vaporizer and USB-C Cable.

• Always follow the instructions in these Instructions for Use when using and servicing the device.

• This Vaporizer is not intended for use by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the Vaporizer by a person responsible for their safety. Children shall not handle the Vaporizer.

• If the user is suffering from respiratory tract or lung disease, the device may only be used after consultation and with the consent of the treating physician. Depending on their density, the vapors may irritate the respiratory tract and lungs, which may cause coughing.

• Do not leave the Vaporizer unattended while it is being operated.

• Store and use the Vaporizer and USB-C Cable only at a sufficient distance from heat sources (oven, stove, fireplace, etc.) and in a dry place where the ambient temperature cannot drop below +5 °C (+41 °F).

• Do not expose the Vaporizer to extreme fluctuations in ambient temperature. Condensation humidity could interfere with the functionality.

• Only use original STORZ & BICKEL accessories and spare parts.

• Do not use the Vaporizer and USB-C Cable in an inappropriate, incorrect, or unreasonable manner, as the manufacturer does not accept any responsibility for any damage resulting from this.

To ensure safe operation of your STORZ & BICKEL VEAZY, please adhere to the following recommendations:

Risk of Injury due to Electric Shock:

• The Vaporizer must be switched off and the USB-C Cable must be disconnected from the power supply after use, before any maintenance work, and during thunderstorms.

• Make sure that the USB-C Cable is not damaged by bending, crushing, or pulling.

• Do not use multiple sockets and/or extension cables.

• Do not use the Vaporizer and USB-C Cable if they are damaged. Repairs may only be carried out by our Service Center. Attempting to repair damage yourself will invalidate the warranty.

• The Vaporizer and USB-C Cable must not be exposed to moisture and humidity.

• Keep the Vaporizer and USB-C Cable away from pets (e.g. rodents) and pests.

• Do not use the Vaporizer and USB-C Cable in a potentially explosive or flammable atmosphere.

Danger of Injury due to Burning/Vapors:

• Do not touch hot surfaces of the Vaporizer (Filling Chamber and the area around the Filling Chamber) during operation and the cooling phase.

• Place the hot Vaporizer only on a solid and heat-resistant surface and make sure that it is not covered by any objects.

• Do not use the Vaporizer near inflammable objects such as curtains, tablecloths, or paper.

• Do not close, cover, or obstruct the openings of the Vaporizer during operation and the cooling phase.

• Do not use the device upside down.

• Before switching on the Vaporizer, ensure that all vapors, e.g., from flammable cleaning agents and disinfectants, have evaporated.

Risk of Injury due to various Causes:

• The packaging material (plastic bags, polystyrene parts, boxes, etc.) must be kept out of the reach of children, as it is a potential source of danger.

• Be careful that small parts of the Vaporizer are not swallowed.

• Be aware of the danger of strangulation through the USB-C Cable.

• Only use the Vaporizer with the recommended herbs and plant parts to be vaporized.

• Monitor your symptoms (e.g., cough, shortness of breath, chest pain) during or after the usage and promptly seek medical attention if you have concerns about your health.

The scope of delivery for the STORZ & BICKEL VEAZY includes the following items:

1. 1 pc. VEAZY Vaporizer

2. 1 pc. Instructions for Use (Concise)

3. 1 pc. Filling Chamber Tool

4. 1 pc. USB-C Cable (USB type C to USB type C plug)

5. 1 pc. Dosing Capsule

6. 3 pcs. Normal Screen, small and 3 pcs. Coarse Screen, small

7. 2 pcs. Seal Ring (Mouthpiece & Rotary Cap)

8. 1 pc. Cleaning Brush

The functional elements of the STORZ & BICKEL VEAZY are:

1. Filling Chamber

2. Mouthpiece

3. Cooling Unit

4. Power Button (ON/OFF)

5. LED Display (upper and lower LED)

6. USB-C Charging Socket

The Cooling Unit of the STORZ & BICKEL VEAZY consists of the following parts:

1. Rotary Cap

2. Mouthpiece

3. Mouthpiece/Rotary Cap Seal Ring

4. Cooling Unit Cap

5. Intermediate Cooling Unit Base

6. Cooling Unit Base

7. Screen (coarse mesh width)

8. Cooling Unit Base Seal Ring

Only vaporize fragrances and aromas from the plant materials listed below, which have been tested for authenticity, purity, and pathogens according to the guidelines of the European Pharmacopoeia (or comparable). The STORZ & BICKEL VEAZY is not intended for the use of tobacco or nicotine-related products. Purchase plants or parts of plants in the pharmacy.

The amount of aromas and fragrances released from your STORZ & BICKEL VEAZY can be influenced by the following factors:

1. Quality: The amount of aroma or fragrance contained in the respective plant material that can be vaporized.

2. Quantity: The amount of vaporization material in the Filling Chamber.

3. Surface: The finer the plant is ground, the greater the surface, and the more aromas and fragrances can be released during the vaporization cycle.

4. Temperature: The higher the temperature, the more aromas and scents are released at once. An increase in temperature should always be a last resort, as the plant material has a less pleasant taste at higher temperatures.

The vaporization process can be repeated with the same contents of the Filling Chamber until vapors are no longer formed at maximum temperature.

To charge the battery of your STORZ & BICKEL VEAZY, follow these steps:

1. Fully charge the battery before first use.

2. Connect the Vaporizer to a USB-C charger using the USB-C Cable supplied.

The charging process is acknowledged with a short illumination of the LED display (green/red/blue) and vibration.

The LED display on your STORZ & BICKEL VEAZY indicates the battery status as follows:

During charging operation:

• Steady blue light: the battery is fully charged.

• Blue, slowly blinking: the battery is between 61 and 98% charged.

• Blue, rapidly blinking: the battery is between 31 and 60% charged.

• Blue flashing: the battery is max. 30% charged.

Following switch off:

• Steady blue light: the battery is between 64 and 100% charged.

• Blue, slowly blinking: the battery is between 32 and 63% charged.

• Blue, rapidly blinking: the battery is between 1 and 31% charged.

• Blue flashing: Battery is depleted.

To fill the chamber of your STORZ & BICKEL VEAZY, follow these steps:

1. Unscrew the Cooling Unit from the Vaporizer by turning it 90° counterclockwise.

2. Fill the Filling Chamber completely with crushed plant material up to the rim. Note that excessively compressed plant material or an overfilled Filling Chamber makes inhalation more difficult.

3. Remove excess plant material around the Filling Chamber.

4. Screw the Cooling Unit onto the Vaporizer by turning it 90° clockwise.

Alternative: Fill the Dosing Capsules, available as optional accessories, with crushed plant material and insert them into the Filling Chamber with the cap facing upwards.

Follow these steps to switch on and heat up your STORZ & BICKEL VEAZY:

1. Press the orange Power Button (ON/OFF) for at least half a second.

2. The Vaporizer will vibrate.

3. The LED display indicates the heating process by a continuous orange light. Depending on battery charge level, ambient temperature, unit, and filling quantity/material in the Filling Chamber, this can take approx. 40 seconds.

4. A double vibration signal and the green continuous light of the LED display indicate that the Base Temperature has been reached.

The STORZ & BICKEL VEAZY offers three factory preset temperature levels which you can cycle through. The default settings are:

• Base Temperature: 180 °C (356 °F)

• Booster Temperature offset: +15 °C (+27 °F), corresponds to 195 °C (383 °F)

• Superbooster Temperature offset: +15 °C (+27 °F), corresponds to 210 °C (410 °F)

Use the following table to understand how to activate each temperature level and what the LED indicators mean:

By double-pressing the Power Button (ON/OFF) in Superbooster Temperature, you get back to Base Temperature.

To reset your STORZ & BICKEL VEAZY to its original factory settings, follow these steps:

1. Press the orange Power Button (ON/OFF) for 10 seconds.

2. A vibration and the LED display will indicate the reset. The reset is acknowledged by running lights (green/red/blue) and a simultaneous vibration.

3. The Base Temperature, Booster Temperature, and Superbooster Temperature will be reset to factory settings.

For the best experience with your STORZ & BICKEL VEAZY, follow this application procedure:

1. Once the heating process is complete, start inhalation immediately.

2. Fold out the Mouthpiece.

3. Put the Mouthpiece between your lips.

4. Inhale evenly for a few seconds but only half as much as possible.

5. Hold your breath for a few seconds.

6. Slowly exhale.

7. Consciously concentrate on the breathing process.

Note: The higher the temperature, the greater the impairment of the flavor.

To end your session and turn off the device:

1. Press the orange Power Button (ON/OFF) for at least half a second.

2. The Vaporizer will vibrate and switch off.

3. Let the Vaporizer cool down completely before storage or cleaning.

Three minutes after the last keystroke or the last application, the STORZ & BICKEL VEAZY switches off automatically to conserve battery power. The Vaporizer will vibrate and switch off.

To reset the automatic switch off timer, press the orange Power Button (ON/OFF) briefly during operation. The timer will be reset to three minutes.

For proper storage of your STORZ & BICKEL VEAZY:

• Store the Vaporizer and USB-C Cable in a dry place away from the elements and out of reach of children or unqualified persons.

• Avoid extended exposure to direct sunlight, as it may cause changes in the color of the device.

To disassemble the Cooling Unit for cleaning, follow these steps:

1. Make sure that the Cooling Unit is screwed onto the Vaporizer.

2. Put the edge of the Mouthpiece into the notch of the Rotary Cap and turn it counterclockwise to open and pull out. Pull off the Seal Ring from the Rotary Cap using the Filling Chamber Tool and the recess.

3. Pull the Mouthpiece out of the Cooling Unit Cap while slightly turning it counterclockwise.

4. Pull off the Mouthpiece Seal Ring using the Filling Chamber Tool and the recess.

5. Pull the Cooling Unit Cap off the Vaporizer.

6. Slide the Intermediate Base off the Cooling Unit Base.

7. Unscrew the Cooling Unit Base from the Vaporizer by turning it 90° counterclockwise.

8. Press out the Screen from the Cooling Unit Base using the Filling Chamber Tool.

9. Lever out the large Base Seal Ring with the Filling Chamber Tool at the recess in the groove.

Clean the Cooling Unit and Mouthpiece no later than 7 days after the last use or whenever deposits are visible. Use the Cleaning Brush, cotton swabs, and paper or cotton cloths for manual cleaning.

Cleaning with rinsing water:

1. Place all disassembled parts in warm rinsing water for at least five minutes.

2. Rinse all parts under running water for at least one minute.

3. Let all parts dry completely.

Alternative Cleaning with Isopropyl Alcohol:

1. Place all parts of the Cooling Unit and the Filling Chamber Screen in isopropyl alcohol for a maximum of 1/2 hour. Do not soak plastic parts for longer to avoid embrittlement.

2. Rinse all parts under running water for at least one minute.

3. Let all parts dry completely.

After cleaning and checking all parts for damage, reassemble the Cooling Unit in the reverse order of disassembly. When assembling, make sure that the Seal Rings are properly seated and insert the Screen into the groove provided for this purpose.

Cleaning the Filling Chamber:

Clean the Filling Chamber with a cotton swab soaked in isopropyl alcohol. Do not moisten cotton swabs too much to prevent ingress of alcohol into the Vaporizer.

Removing the Screen:

If a Screen is clogged, it must be replaced.

1. Cautiously start levering the Screen out of the rim from the side of the Filling Chamber using pointy tweezers. The Screen will detach from the groove.

2. Pinch the Screen with the tweezers and remove it from the Filling Chamber.

3. Clean the Screen with rinsing water or isopropyl alcohol, or replace a damaged Screen with a new one.

Installing the Screen:

1. Bend the cleaned Screen beforehand or use a new Screen.

2. Insert the Screen into the Filling Chamber with the curved side facing upwards.

3. Press the Screen flat into the provided groove using the Filling Chamber Tool.

To clean the exterior of your STORZ & BICKEL VEAZY:

1. Switch off the Vaporizer.

2. Disconnect the Vaporizer and the USB-C Cable from the mains supply.

3. Clean the housing of the Vaporizer and the USB-C Cable only with a dry soft or damp cloth.

If you experience issues with your STORZ & BICKEL VEAZY, refer to the following troubleshooting table: