STORZ & BICKEL MIGHTY (02) PDF Document

The scope of delivery for the STORZ & BICKEL MIGHTY includes:

• MIGHTY Vaporizer

• Power Adapter

• Instructions for Use

• 1 Set of Spare Seal Rings (one of each type)

• 3 pcs. Spare Screens

• Herb Mill

• Cleaning Brush

• Filling Aid

• Dosing Capsule

• Drip Pad

An optional accessory, the 12 Volt Car Charger, is also available.

The main functional elements of the STORZ & BICKEL MIGHTY vaporizer are:

• Mouthpiece: Where you inhale from.

• Cooling Unit: Cools the vapor before inhalation.

• Filling Chamber: Where you place the plant material.

• Actual Temperature Display: Shows the current temperature of the device.

• Set Temperature Display: Shows the target temperature you have set.

• Plus / Minus Temperature Buttons: Used to increase or decrease the set temperature.

• ON/OFF Switch: The orange button used to turn the device on and off.

• Battery Charging Display: Shows the current battery level.

• Charging Socket: Port for connecting the power adapter.

• Filling Chamber Tool: A tool stored under the Type Label on the rear of the device, used for maintenance.

• Type Label: Located on the rear of the device.

Please observe the following safety recommendations when using your STORZ & BICKEL MIGHTY:

• Keep packaging material out of reach of children.

• Check the device housing for damage before use. Avoid contact with any leakage liquid.

• Supervise people who require assistance during application.

• Keep the device and accessories away from babies and infants as small parts can be a choking hazard.

• Only use the supplied power adapter or the optional 12 Volt car charger from Storz & Bickel to charge the battery.

• If you have problems, immediately unplug the power adapter from the socket.

• Unwind the power adapter cord completely, keep it away from impacts, children, liquids, and heat sources, and do not crush or kink it.

• Do not use multiple sockets or extension cables unless they are quality certified and exceed the required power (Ampere).

• Place the device on a stable, flat surface away from heat sources after use.

• Do not operate near flammable objects like curtains or paper.

• Keep the device away from pets that could damage the power cord.

• Do not attempt to repair the device or power adapter yourself.

• Do not leave the device unattended while operating. Switch it off after use.

• Do not block or obstruct the ventilation slots.

• The Filling Chamber is metal and will be hot during and after use. Do not touch it until it has cooled down.

• Always disconnect from power before cleaning. Clean only with a dry or slightly damp cloth. Never immerse in water.

• Do not use in damp or wet conditions, and do not expose to rain.

• Do not use in an atmosphere with risk of explosion or ignition.

The STORZ & BICKEL MIGHTY Vaporizer is intended to release fragrances or aromas from the herbs and other plant materials listed in the user manual. These aromatic substances are released through vaporization by heated air and may be directly inhaled.

The device may only be used with the recommended vaporizing media. Any other use is inappropriate and potentially dangerous. The use of other substances can present a health risk.

The STORZ & BICKEL MIGHTY Vaporizer is not FDA approved.

The following is an overview of plants suitable for vaporization in the STORZ & BICKEL MIGHTY and their recommended temperature settings.

Plant name	Botanical name	Portion of the plant used	Temperature-setting
Eucalyptus	Eucalyptus globulus	the leaves	130°C (266°F)
Hops	Humulus lupulus	the cones	154°C (309°F)
Chamomile	Matriarca chamomilla	the blossoms	190°C (374°F)
Lavender	Lavandula angustifolia	the blossoms	130°C (266°F)
Lemon balm	Melissa officinalis	the leaves	142°C (288°F)
Sage	Salvia officinalis	the leaves	190°C (374°F)
Thyme	Thymus vulgaris	the herb	190°C (374°F)

WARNING: Please consult your doctor or pharmacist if you have any medical concerns. It is possible that some plants may cause allergic reactions for the user. If this occurs, it is urgently recommended to refrain from further use of such plants. Only use plant parts that have been verified for genuineness, purity, and pathogenic germs.

The amount of aromas and fragrances released during vaporization can be influenced by the following factors:

1. Quality: The amount of aroma or fragrance contained in the plant material.

2. Quantity: The amount of vaporization material in the Filling Chamber.

3. Surface: The finer the plant is ground, the greater the surface area, which allows more aromas and fragrances to be released.

4. Temperature: The higher the temperature, the more aromas and fragrances will be released at once. However, increasing the temperature should be a last resort, as it can make the plant material taste more roasted.

The vaporization cycle can be repeated multiple times with the same contents until the aromas and fragrances are completely released. When no more vapor is produced at the highest temperature, the material is exhausted and should be replaced.

If you encounter issues with your STORZ & BICKEL MIGHTY, refer to the following troubleshooting guide:

Problem	Possible Cause/Remedy
MIGHTY cannot be switched on.	Please ensure that the MIGHTY’s battery is charged or the Vaporizer is connected via the power adapter to a functioning mains socket. If the Vaporizer still does not work, then the device is faulty. In this case, disconnect from the mains without delay and get in touch immediately with our Service Center.
The display of the MIGHTY shows: ERR 001.	Battery temperature is too high. Allow the Vaporizer to cool down.
The display of the MIGHTY shows: ERR 002.	Battery temperature is too low. Warm up the Vaporizer.
The display of the MIGHTY shows: ERR 003.	The power adapter is not suitable. Please use an original Storz & Bickel power adapter or 12 Volt car charger.
The display of the MIGHTY shows: ERR 004.	The Vaporizer is faulty. In this case, disconnect from the mains without delay and get in touch immediately with our Service Center.

If these tips do not resolve the issue, please unplug the power adapter and contact the Service Center. Do not attempt to open or repair the device or power adapter yourself, as this will cause damage and invalidate the warranty.

To charge the battery of your STORZ & BICKEL MIGHTY:

1. Connect the power adapter to the charging socket on the Vaporizer.

2. Plug the power adapter into a suitable power socket. The display will light up for a moment and the device will vibrate briefly to indicate that charging has started.

3. The battery charging display (a battery symbol with six fields) will light up and start to flash. The number of visible fields indicates the current charge level.

4. When the battery is fully charged, the display will stop flashing and show all six fields as full.

5. Once charging is complete, disconnect the power adapter from the mains socket first, and then unplug it from the Vaporizer.

A full charge takes about two hours if the battery is completely discharged. It is recommended to fully charge the device before its first use. You can also charge it with the optional 12 Volt car charger.

Yes, the STORZ & BICKEL MIGHTY can be operated with the power adapter connected, even when the batteries are completely discharged. This is referred to as Mains Operation. To do this, simply connect the power adapter to the device and a power outlet as you would for charging.

Yes, the STORZ & BICKEL MIGHTY has an automatic switching off feature to save battery capacity. The device will automatically switch off two minutes after the last press of a button or the last application. The shut-off is indicated by a short vibration. You can reset this two-minute timer at any time by briefly pressing the orange ON/OFF switch during operation.

To heat up your STORZ & BICKEL MIGHTY:

1. Ensure the device has a full Filling Chamber and the Cooling Unit is mounted.

2. Press the orange ON/OFF switch for at least half a second. The device will respond with a short vibration and the display will turn on, showing the set and actual temperatures.

3. The device will begin heating to the set basic temperature. Heating can take up to two minutes.

4. When the set temperature is reached, the device will signal this with a short double vibration.

Booster Temperature:

If the basic temperature is not providing enough evaporation, you can activate the booster temperature by double-clicking the orange ON/OFF switch. This will heat the device to a higher, pre-set temperature. When the booster temperature is reached, it is signaled by a short double vibration and a blinking Set Temperature display.

The temperature on the STORZ & BICKEL MIGHTY can be set between 40°C and 210°C (104°F and 410°F). To adjust the temperature:

• Use the plus (+) and minus (-) buttons located to the right and left of the Set Temperature Display.

• Briefly tapping the plus or minus button will change the set temperature in 1-degree increments.

• Pressing and holding the plus or minus button will cause the set temperature to change continuously in that direction.

The current actual temperature is always shown on the upper line of the display. The booster temperature can also be adjusted in the same way, but it cannot be set lower than the basic set temperature.

To change the temperature display unit on your STORZ & BICKEL MIGHTY, simultaneously tap on the plus (+) button and the minus (-) button. The display will change from degrees Celsius to degrees Fahrenheit, or vice versa.

To reset your STORZ & BICKEL MIGHTY to the factory default settings, press and hold the ON/OFF button for ten seconds while the device is switched on. A vibration will signal that the reset is complete. The basic temperature will be reset to 180°C (356°F) and the booster temperature will be reset to 195°C (383°F).

1. Remove the Cooling Unit from the Vaporizer by turning it 90 degrees counterclockwise.

2. Always fill the Filling Chamber completely up to the plastic rim with ground plant material.

3. Do not compress the material too much, as this can impede airflow.

4. Clean any excess plant material from around the filling aperture to ensure the Cooling Unit can be fitted properly.

For a partially filled chamber: If you do not wish to fill the chamber completely, it is recommended to place the included Drip Pad over the herbs before mounting the Cooling Unit. This prevents the material from shifting around, which would allow hot air to bypass it.

First, fill the Filling Aid by removing its upper cap and filling the bowl with ground plant material, then replace the cap.

To fill the vaporizer using the Filling Aid:

1. Remove the Cooling Unit from the Vaporizer.

2. Remove the lower cap from the Filling Aid by turning it counterclockwise.

3. Place the Filling Aid onto the Vaporizer and attach it by turning it clockwise.

4. Remove the upper cap from the Filling Aid.

5. Pull out the plug from the center of the Filling Aid and use it to push plant material from the Filling Aid’s bowl through the central opening and into the Filling Chamber.

6. Ensure the Filling Chamber is not overfilled. The top of the plant material should be below the lower rim of the Filling Aid.

7. Re-insert the plug into the central opening and screw the upper cap back onto the Filling Aid.

8. Unscrew the Filling Aid from the Vaporizer with a 90-degree rotation and re-mount the Cooling Unit by rotating it clockwise through 90 degrees.

1. First, mount the filled Cooling Unit on the Vaporizer and heat it up to your desired temperature.

2. Once the device has reached the set temperature (indicated by a double vibration), fold out the Mouthpiece.

3. Take the Mouthpiece between your lips and inhale slowly and evenly for several seconds.

4. For best results, inhale only about half the air you normally can, hold your breath for a few seconds, and then exhale slowly.

5. After your session, turn off the MIGHTY Vaporizer by pressing the orange ON/OFF switch for at least half a second. The device will acknowledge shut down with a short vibration.

Caution: The Filling Chamber will be hot after use. Do not touch it until it has had time to cool down.

To disassemble the MIGHTY Cooling Unit:

1. Pull out the Mouthpiece from the Cooling Unit Cap, rotating it slightly back and forth. Then pull off the Mouthpiece Seal Ring.

2. Open the Cap Lock by pulling it rearwards.

3. Separate the Cooling Unit Cap from the Cooling Unit Base by pulling the cap upwards.

4. Remove the large and small Base Seal Rings. The large Seal Ring can be levered out of its recess using the Filling Chamber Tool.

5. Push the upper Screen downwards out of the Cooling Unit Cap from above, using the supplied Filling Chamber Tool.

6. The Cap Lock itself only needs to be removed if you intend to immerse the Cooling Unit in alcohol, as extended contact can cause whitening. To remove it, pull up on one side.

To reassemble, perform these steps in reverse order. Ensure that all Seal Rings are properly seated, especially the Mouthpiece Seal Ring, which must sit completely in the cap. The upper Screen must be inserted carefully back into its groove.

The component parts of the Cooling Unit must be cleaned regularly to guarantee proper operation and pure flavor. The condensate can be sticky, and the unit is easier to dismantle when it is still warm.

1. Disassemble the Cooling Unit as described in the manual.

2. Use the included Cleaning Brush, cotton swabs, or paper towels for cleaning.

3. As a solvent, you can use alcohol (ethanol) or warm water with dish soap.

4. Important: Do not immerse any plastic components in alcohol for longer than one hour, as this can lead to discoloration or embrittlement.

5. After cleaning, check all parts for damage and allow them to dry completely before reassembling.

Warning: Alcohol (ethanol) is flammable and may ignite easily.

To remove the lower Filling Chamber Screen:

Use the Filling Chamber Tool and push it in along the indentation of the Filling Chamber. This will cause the Screen to arch and detach from the notch in the chamber wall.

To insert a new Screen:

It is easier to insert the new Screen if you slightly curve it first. Insert it with the curved side facing up. Then, using the Filling Chamber Tool, press the screen flat so that its edges seat properly into the groove at the bottom of the Filling Chamber.

The Dosing Capsules allow you to pre-fill portions of ground plant material for convenient use.

Filling the Dosing Capsules:

1. Grind the plant material using the included Herb Mill.

2. Use the Magazine Cap as a funnel to fill an empty Dosing Capsule.

3. Attach the cap onto the Dosing Capsule.

4. Repeat until you have filled the desired number of capsules (the Magazine holds up to 8).

5. To fill with aromatic oils, use a Dosing Capsule with an inserted Drip Pad. Do not overfill the Drip Pad; it can contain up to 5 drops.

Using the Dosing Capsules in the Vaporizer:

1. Remove the Cooling Unit from the MIGHTY Vaporizer.

2. Insert a filled Dosing Capsule, with the cap facing upwards, into the Filling Chamber.

3. Re-mount the Cooling Unit by rotating it clockwise 90 degrees.

Power Adapter:

• Power consumption: 36 W

• Supply voltage: 100-240 V / 50-60 Hz

• Output voltage: 12 V DC

STORZ & BICKEL MIGHTY Vaporizer:

• Supply voltage: 12 V DC

• Power required by MIGHTY Vaporizer: 36 W

• Operating temperature: 5°C – 40°C / 41°F – 104°F

• Vaporization Temperature: adjustable between approx. 40°C – 210°C / 104°F – 410°F

• Size: 14 x 8 x 3 cm (5.5 x 3.2 x 1.2 inch)

• Weight: approx. 235 g (0.5 lb)