SONY BRAVIA KD-65XG80XX (01) PDF Document

Count how many times it flashes (the interval time is three seconds).

Reboot the SONY BRAVIA KD-65XG80XX by disconnecting the mains lead until the illumination LED stops flashing red, then turn on the TV.

If the problem persists, disconnect the mains lead, and contact your dealer or Sony service centre with the number of times the illumination LED flashes.

Restart your SONY BRAVIA KD-65XG80XX by pressing the power button on the remote control until a message appears. The TV will restart.

If the TV does not recover, try unplugging the mains lead. Then press the power button on the TV and wait for two minutes, and plug in the mains lead.

Refer to the Help menu by pressing HELP on the remote control.

For more detailed information, select [Help Guide] from the Help menu on your TV.

Enter 9999 for the PIN code and select [Change PIN code].

Replace the batteries.

Connect and set up the IR Blaster (for models with supplied IR Blaster only).

Connect an HDMI CEC compatible device (except models with supplied IR Blaster) and change to that input.

When the TV is off, press  to power on.

When the TV is on, press and hold  to power off.

Press  repeatedly to change the function, then press + or – button to:

• Adjust the volume.
• Select the channel.
• Select the input source of TV.

In TV mode: Display and select the input source.

In Text mode: Hold the current page.

Switch between digital and analogue input using the DIGITAL/ANALOG button.

Switch between TV or RADIO broadcasts using the TV/RADIO button.

Return to the previous screen or exit from the menu using the EXIT button. When an Interactive Application service is available, press to exit from the service.

Display information using the / button.

Display text information using the  (Text) button.

Access the “Google Play” online service using the Google Play button.

Use voice search by pressing the (Microphone) button. (e.g., Search various content by voice.) The voice search requires an Internet connection.

Display the connected External Box (cable/satellite box) menu using the EXT.BOX MENU button.

• For models with supplied IR Blaster, connect and set up the IR Blaster.
• The External Box menu may be displayed for some HDMI CEC compatible devices when the IR Blaster is not supplied/connected.

Use the //// (Navigation D-Pad) for on screen menu navigation and selection.

Switch to a TV channel or input and display the TV Menu Bar using the TV button.

Adjust the volume using the +/– (Volume) buttons.

Mute the sound using the  (Mute) button. Press again to restore the sound.

In Text mode: Select the next () or previous () page using the PROG +/–// buttons.

Record the currently viewed program on the USB HDD using the REC button.

Display the Title list using the TITLE LIST button.

Jump back and forth between two channels or inputs. The TV alternates between the current channel or input and the last channel or input that was selected using the (Jump) function.

Turn subtitles on or off (when the feature is available) using the (Subtitle setting) button.

Display the Help menu using the HELP button. Help Guide can be accessed from here.

When the TV is off, press  to power on.

When the TV is on, press and hold  to power off.

Press  repeatedly to change the function, then press + or – button to: Adjust the volume, Select the channel, or Select the input source of TV.

The illumination LED lights up or blinks according to the status of the TV.

Press  repeatedly to change the function, then press + or – button to: Adjust the volume, Select the channel, or Select the input source of TV.

Select the sound of the multilingual source or dual sound for the programme currently being viewed (depend on programme source) using the AUDIO button.

Operate media contents on the TV and connected BRAVIA Sync-compatible device using the ////// buttons.

Install the SONY BRAVIA KD-65XG80XX so that its Table-Top Stand does not protrude out from the TV stand (not supplied). If the Table-Top Stand protrudes out from the TV stand, it may cause TV set to topple over, fall down, and cause personal injury or damage to the TV.

Only qualified service personnel should carry out wall-mount installations for the SONY BRAVIA KD-65XG80XX.

Before transporting the TV set, disconnect all cables.

Two or three people are needed to transport a large TV set.

When transporting the TV set by hand, hold it as shown below. Do not put stress on the LCD panel and the frame around the screen.

When lifting or moving the TV set, hold it firmly from the bottom.

When transporting the TV set, do not subject it to jolts or excessive vibration.

When transporting the TV set for repairs or when moving, pack it using the original carton and packing material.

To perform IR Blaster setup, press HOME and select [Settings] t [External inputs] t [IR Blaster setup].

The specifications for the Wireless LAN (IEEE 802.11ac/a/b/g/n) frequency range and output power for the SONY BRAVIA KD-65XG80XX are as follows:

The specifications for the Bluetooth frequency range and output power for the SONY BRAVIA KD-65XG80XX are as follows:

The specifications for the RMF-TX310E/TX220E Bluetooth frequency range and output power for the SONY BRAVIA KD-65XG80XX are as follows:

The approximate dimensions (w × h × d) with Table-Top Stand for the SONY BRAVIA KD-65XG80XX are 146.3 × 90.9 × 33.6 cm.

The approximate dimensions (w × h × d) without Table-Top Stand for the SONY BRAVIA KD-65XG80XX are 146.3 × 84.5 × 8.0 cm.

The approximate mass (Approx.) with Table-Top Stand for the SONY BRAVIA KD-65XG80XX is 22 kg.

The approximate mass (Approx.) without Table-Top Stand for the SONY BRAVIA KD-65XG80XX is 20.9 kg.

The power consumption in [Standard] mode for the SONY BRAVIA KD-65XG80XX is 156 W.

The power consumption in [Vivid] mode for the SONY BRAVIA KD-65XG80XX is 258 W (for KD-65XG8196 / 65XG8096 models).

The annual energy consumption for the SONY BRAVIA KD-65XG80XX is 216 kWh per year.

The specified standby power consumption is 0.50 W (25 W in software/EPG update mode) for the SONY BRAVIA KD-65XG80XX.

The display resolution is 3,840 dots (horizontal) × 2,160 lines (vertical) for the SONY BRAVIA KD-65XG80XX.

The output rating for USB 1/2 is 5 V , 500 mA MAX, and for USB 3 is 5 V , 900 mA MAX for the SONY BRAVIA KD-65XG80XX.

The operating temperature for the SONY BRAVIA KD-65XG80XX is 0 ºC – 40 ºC, and the operating humidity is 10 % – 80 % RH (non-condensing).

The power requirements for the SONY BRAVIA KD-65XG80XX, except models with supplied mains adaptor, are 220 V – 240 V AC, 50 Hz.

For models with supplied mains adaptor, the SONY BRAVIA KD-65XG80XX requires 19.5 V DC with mains adaptor. The rating is Input 220 V – 240 V AC, 50 Hz.

The Energy Efficiency Class for the SONY BRAVIA KD-65XG80XX is A.

The screen size (measured diagonally) for the SONY BRAVIA KD-65XG80XX is approximately 163.9 cm / 65 inches.

The AUDIO OUT / supports a 3-pole stereo mini jack only for the SONY BRAVIA KD-65XG80XX.

To listen to the TV’s sound through the connected equipment on the SONY BRAVIA KD-65XG80XX, press HOME. Select [Settings] t [Sound] t [Headphone/Audio out] and then select the desired item.

To enjoy high quality 4K 50p/60p contents on the SONY BRAVIA KD-65XG80XX, connect a Premium High Speed HDMI cable to the HDMI IN 2/3 and set the [HDMI signal format] to [Enhanced format].

Connect your audio system to the HDMI IN 3 port on the SONY BRAVIA KD-65XG80XX to route TV audio to your audio system. An audio system that supports HDMI ARC can send video to the TV, and receive audio from the TV via the same HDMI cable. If your audio system does not support HDMI ARC, an additional connection with DIGITAL AUDIO OUT (OPTICAL) is necessary.

When transporting the TV set for repairs or when moving, pack it using the original carton and packing material.

Take care when removing the Table-Top Stand from the TV to prevent it from falling over and damaging the surface that the TV is sitting on.

For safety reasons, it is strongly recommended that you use Sony accessories, including the Wall-Mount Bracket SU-WL450, when installing the SONY BRAVIA KD-65XG80XX on the wall.

Be sure to use the M6 screws supplied with the Wall-Mount Bracket when attaching the Wall-Mount Bracket to the TV set. The supplied screws are designed as indicated by illustration when measured from the attaching surface of the Wall-Mount Bracket. The diameter and length of the screws differ depending on the Wall-Mount Bracket model. Use of screws other than those supplied may result in internal damage to the TV set or cause it to fall, etc.

When transporting the TV set by hand, hold it as shown below. Do not put stress on the LCD panel and the frame around the screen.

To know the software version on the SONY BRAVIA KD-65XG80XX, press HELP on the remote control. To check on the remote control, press HOME, then select [Settings]  [Voice Remote Control]  [Software version]. The software loaded on this radio equipment is verified to comply with the essential requirements of the Directive 2014/53/EU.

Sony strongly recommends you to update the TV software by selecting [Update Now]. These software updates improve your TV performance or add new features. The following screen with [Updating…] will appear and the illumination LED flashes white while software is updating.

Do not unplug the mains lead during the software update. If you do, the software update may not finish completely, and it may cause a software malfunction. Software updates can take up to 15 minutes.

When you plug in the TV, the TV may not be able to turn on for a while even if you press the power button on the remote control or the TV. It takes time to initialize the system. Wait for about one minute, then operate it again.

Check the antenna (aerial)/cable connection and booster settings.

Select terrestrial/cable service by pressing DIGITAL/ANALOG on the remote control. If the broadcasting service is not displayed, press TV and then press DIGITAL/ANALOG.

Terrestrial signal might be suppressed if there is a strong signal supplied nearby.

After moving to a new house or trying to receive new services, attempt a service search by selecting [Digital tuning].

Check the satellite cable connection.

When the message [No signal. LNB overload detected…] is displayed, unplug the mains lead. Then, ensure the satellite cable is not damaged and the satellite signal line is not short-circuited in the satellite connector.

The supported video formats for HDMI IN on the SONY BRAVIA KD-65XG80XX include:

• 4096 × 2160p (50, 60 Hz)*2*3, 4096 × 2160p (24 Hz)*2, 3840 × 2160p (50, 60 Hz)*3, 3840 × 2160p (24, 25, 30 Hz), 1080p (30, 50, 60 Hz), 1080/24p, 1080i (50, 60 Hz), 720p (30, 50, 60 Hz), 720/24p, 576p, 576i, 480p, 480i, PC Formats*4.

The supported audio formats for HDMI IN on the SONY BRAVIA KD-65XG80XX include:

• 5.1 channel linear PCM: 32/44.1/48/88.2/96/176.4/192 kHz 16/20/24 bits, Dolby Digital, Dolby Digital Plus and DTS.

HDMI IN 3 supports ARC (Audio Return Channel) on the SONY BRAVIA KD-65XG80XX.

DIGITAL AUDIO OUT (OPTICAL) on the SONY BRAVIA KD-65XG80XX supports Two channel linear PCM: 48 kHz 16 bits, Dolby Digital, DTS.

The approximate dimensions (w × h × d) with Table-Top Stand for the SONY BRAVIA KD-65XG81XX are 146.3 × 90.7 × 33.7 cm.

The approximate dimensions (w × h × d) without Table-Top Stand for the SONY BRAVIA KD-65XG81XX are 146.3 × 84.5 × 8.0 cm.

The approximate mass (Approx.) with Table-Top Stand for the SONY BRAVIA KD-65XG81XX is 22.1 kg.

The approximate mass (Approx.) without Table-Top Stand for the SONY BRAVIA KD-65XG81XX is 20.9 kg.