X-SENSE XC01 (01) PDF Document

Free English X-SENSE XC01 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.

CLICK HERE TO DOWNLOAD X-SENSE XC01 (01) PDF DOCUMENT

If this is not the document you want for this product, click here to see if we have any other documents for this product.

How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.

What is the purpose of the Test/Silence button on the X-SENSE XC01?

The Test/Silence button is used to test the unit’s electronics and to silence the unit during an alarm.

What is the procedure to enter the test mode for the X-SENSE XC01?

You should first wake up your alarm by pressing the test button. Once the alarm has woken up, the LCD display will activate. Then, press the test button again until you hear a short beep, indicating that the alarm has entered the test mode.

What happens immediately after starting a test on the X-SENSE XC01?

After a test has begun, the alarm will sound and the LED indicator will flash red. This does not indicate that CO is present.

What happens if the Test button is pressed during an alarm state on the X-SENSE XC01?

If you press the test button during an alarm state, the unit will enter the silence mode.

What are the programmed CO alarm levels for the X-SENSE XC01?

The X-SENSE XC01 is programmed to sound an alarm at the following CO concentrations within the time periods listed:

30 ppm over 120 minutes,
50 ppm for 60–90 minutes,
100 ppm for 10–40 minutes,
and 300 ppm for 0–3 minutes.

What display and indicator behavior occurs when CO is detected and the alarm sounds on the X-SENSE XC01?

When CO is detected and the alarm sounds, the CO concentration will be displayed on the LCD and a blue backlight will be lit. The LED indicator will flash red and the alarm will issue 4 short beeps, repeating the cycle every 5.8 seconds.

What are the effects on adults of a 100 PPM concentration of CO?

Slight headache, nausea, fatigue (flu-like symptoms).

What are the effects on adults of a 200 PPM concentration of CO?

Dizziness and headache within 2–3 hours.

What are the effects on adults of a 400 PPM concentration of CO?

Nausea, frontal headache, drowsiness, confusion and rapid heart rate. Risk to life after over 3 hours of exposure.

What are the effects on adults of an 800 PPM concentration of CO?

Severe headaches, convulsions, vital organ failures. Death possible within 2–3 hours.

What indicates a low-battery warning on the X-SENSE XC01?

If the battery voltage is low, the unit will chirp once and the LED indicator will flash yellow every 60 seconds to indicate the need for battery replacement.

What happens if the test button is pressed when the X-SENSE XC01 has a low battery?

If you press the test button when there is a low battery, the low battery signal will temporarily cease for 10 hours; if you press the test button again, the unit will enter the test mode and then the standby mode.

What is the end-of-life indication for the X-SENSE XC01?

Once the maximum lifetime (10 years) is reached, the alarm will deliver 3 beeps and the LED indicator will flash yellow 3 times every 60 seconds. This end-of-life signal can be temporarily silenced for 22 hours by pressing the test button.

What is the duration limit for using the end-of-life silence feature on the X-SENSE XC01?

The end-of-life silence feature can only be used for a total of 30 days. After 30 days, the end-of-life signal cannot be silenced.

What are the ideal guidelines for installing a CO alarm in a room with a fuel-burning appliance using the X-SENSE XC01?

The following guidelines should be considered when installing a CO alarm in a room with a fuel-burning appliance (see Figure 1):

If it is mounted on a wall, it should be installed at a height greater than the height of any door or window, but should still be at least 150 mm (5.9 inches) below the ceiling.
The CO alarm should have a horizontal distance between 1 m (3.3 feet) and 3 m (10 feet) from any potential CO source.
If there is a partition in the room, the CO alarm should be installed on the same side of the partition as the potential CO source.

What are the guidelines for installing the X-SENSE XC01 in a bedroom or room without a fuel-burning appliance?

When installing the X-SENSE XC01 in a bedroom or room without a fuel-burning appliance (see Figure 2):

Mount the CO alarm relatively close to the breathing zone of the occupant.
Install the alarm such that the LED indicator is viewable when the occupant is near the alarm.

What are locations to avoid when installing the X-SENSE XC01?

To avoid causing damage to the unit, to provide optimum performance, and to prevent unnecessary nuisance alarms, do not locate X-SENSE XC01 alarms in the following areas:

In garages or in any extremely dusty, dirty or greasy areas.
Where there is the possibility of smoke or fumes under normal operating circumstances.
In poorly ventilated kitchens, garages and furnace rooms. Keep the CO alarms at least 1.5 m (5 feet) from potential smoke or fume sources (e.g. stoves, furnaces, water heaters, space heaters) if possible.
In areas where a 1.5 m (5-foot) distance from a potential smoke or fume source is not possible. In modular, mobile or smaller houses, it is recommended the CO alarm be placed as far from any potential smoke or fume sources.
Within 1.5 m (5 feet) of any cooking appliance.
In extremely humid areas. This alarm should be at least 3 m (10 feet) from a bath or shower, sauna, humidifier, vaporizer, dishwasher, laundry room, utility room or other sources of high humidity.
In areas where the temperature is colder than 4.4°C (40°F) or hotter than 37.8°C (100°F). For example, non-air-conditioned crawl spaces, unfinished attics, uninsulated or poorly insulated ceilings, porches and garages.
Where the air is turbulent, such as near ceiling fans, heat vents, air conditioner vents, fresh air return vents, or open windows. Excessive air flow may prevent any CO from reaching the sensors.
In direct sunlight.

How is the X-SENSE XC01 activated?

This device is equipped with a battery insulating film to ensure it will not be powered on during transportation before it has shipped from the factory. When installing this product, you will need to pull out the film before powering on and activating the device. Before use, pull out the battery insulating film from the battery compartment to power on the device. After the device is turned on, the buzzer will beep once, the LCD backlight will light up, and the LED indicator will flash through 8 cycles (yellow/green/red). The device will then enter standby mode.

What is the process to open the battery compartment cover on the X-SENSE XC01?

Hold the alarm with both hands and put your thumbs on both ends of the battery compartment cover. Then, push the cover upwards with some force to remove it.

What are the steps for wall mounting the X-SENSE XC01?

1. Choose a suitable installation location by referring to the “Where to Install” section.

2. Remove the indication sticker from the packaging and refer to the hole locations on the sticker. Draw two screw holes according to the size and layout of the mounting holes on the back of the product. Drill the screw holes 30 mm (1.18 inches) deep using a Ø 6.0 mm (1/4-inch) drill bit. Note that the distance between the center of the two holes is 74 mm (2.9 inches).

3. Insert the anchor plug into the screw hole and hammer it in until the head of the anchor plug is flush with the wall.

4. Use the two provided screws or 3.5 × 25 mm countersunk screws to screw into the two anchor plugs. Be sure to leave a 5 mm (1/5-inch) gap between the head of the anchor plugs and the screws, which will allow for easy device mounting.

5. Mount and lock the device onto the wall by aligning the two mounting slots on the back of the device with the screws on the wall.

6. Test the device by pushing the test button to make sure that the device is functioning properly.

How can the X-SENSE XC01 be installed on a table?

The base of the detector has two feet built into the design that allow it to stand freely on a flat surface.

What is the procedure for performing an Alarm Test on the X-SENSE XC01?

For the X-SENSE XC01, push the test button once to wake up the alarm, and press the test button again when the LCD is on. The device will beep 4 times twice, and the LED will flash red. The LCD will display “—,” “PAS,” the peak CO concentration recorded since the previous reset, and finally “0.” This indicates that the device is functioning properly.

How is the Peak CO Concentration Memory and Reset performed on the X-SENSE XC01?

Each time you push the test button, the LCD displays the peak CO concentration recorded since the previous reset. The peak CO concentration will be displayed for 5 seconds, and then the device will enter standby mode. To reset the peak CO concentration: During the 5 seconds when the LCD displays the peak CO concentration, press and hold the test button for 3 seconds, the device will beep, the LED will flash green, and the peak CO concentration will be reset with LCD displaying “0.”

When will the silence function of the X-SENSE XC01 not be enabled during an alarm state?

If the CO concentration is above 300 ppm, the silence function cannot be enabled.

What happens if the CO density still exceeds the alarm threshold after silence mode is activated on the X-SENSE XC01?

If the CO density still exceeds the alarm threshold after 6 minutes, the unit will re-enter the alarm state. Otherwise, the unit will exit the silence mode after 9 minutes and resume normal operation.

What is the audible alarm and LED indicator behavior when the X-SENSE XC01 is Powering On?

The Audible Alarm is 1 quick beep. The LED Indicator runs through 8 cycles (yellow/green/red) in sequence.

What is the LED indicator behavior in Standby Mode for the X-SENSE XC01 (XC01/XC04)?

The LED Indicator flashes green once every 60 seconds.

What is the alarm status displayed when a CO concentration ranging from 30 to 999 ppm has been present for a certain time period on the X-SENSE XC01?

The LCD Display shows the CO concentration (e.g., 124 PPM), the blue backlight is lit, and the LED indicator flashes red 4 times every 5.8 seconds. The Audible Alarm is 4 beeps repeating every 5.8 seconds. The Remark notes that a Dangerous CO concentration is detected, and has reached the alarm status. Please refer to “What to Do When the Alarm Sounds”.

What is the alarm status displayed when a CO concentration ranging from 30 to 999 ppm has been detected for less than the allotted detection period on the X-SENSE XC01?

The LCD Display shows the CO concentration (e.g., 124 PPM). The LED Indicator flashes green once every 60 seconds. The Remark notes that Dangerous CO concentration is detected, but has not reached the alarm status. Potential dangerous CO conditions exist. Please search for the CO source first. Open nearby windows and doors, and immediately move to fresh air.

What is the audible alarm behavior when the CO concentration level drops below the alarm threshold on the X-SENSE XC01 during an alarm state?

Alarm cancellation: when the CO concentration level drops below the alarm threshold, the alarm signal will stop.

What is displayed during Test Mode on the X-SENSE XC01?

The LCD Display shows “—“, then “PAS”, then the peak CO level recorded since the previous reset (e.g., 300 PPM). The LED Indicator has 2 sets of 4 red flashes. The Audible Alarm has 2 sets of 4 quick beeps. The Remark notes this is the Peak CO level recorded since the previous reset.

What is displayed during Silence Mode on the X-SENSE XC01 when an alarm condition is present (e.g., 124 PPM)?

The LCD Display shows the CO concentration (e.g., 124 PPM). The LED Indicator flashes red 4 times every 5.8 seconds. The Remark notes that the CO silence mode ends after 9 minutes, the unit will exit silence mode.

What is displayed during Silence Mode on the X-SENSE XC01 when there is a Low Battery indication?

The LCD Display shows “Lb” and the PPM value. The LED Indicator flashes yellow once every 60 seconds. The Remark notes that silence mode during low battery: after 10 hours, the unit will exit silence mode.

What is displayed when the X-SENSE XC01 is exiting Silence Mode due to End of Life signal?

The LCD Display shows “End” and the PPM value. The LED Indicator flashes yellow 3 times every 60 seconds. The Remark notes that silence mode during the end of cycle: after 22 hours, the unit will exit silence mode.

What is displayed when the X-SENSE XC01 is Exiting Silence Mode?

The LCD Display shows 0 PPM. The LED Indicator flashes green 3 times. The Remark notes this means Exiting silence mode.

What is the Low Battery indication on the X-SENSE XC01?

The LCD Display alternates between “Lb” and current CO level. The LED indicator flashes yellow once every 60 seconds. The Audible Alarm is 1 quick beep every 60 seconds. The Remark notes that for XC01/XC04, the unit must be replaced immediately.

What is the Fault indication on the X-SENSE XC01?

The LCD Display shows “Err” and the PPM value. The LED Indicator flashes yellow 2 times every 60 seconds. The Audible Alarm is 2 beeps every 60 seconds. The Remark states: Please clean your alarm and see if it is working normally. If “Err” continues to display, the unit has malfunctioned and must be replaced immediately.

What is the End of Life indication on the X-SENSE XC01?

The LCD Display shows “End” and the PPM value. The LED Indicator flashes yellow 3 times every 60 seconds. The Audible Alarm is 3 quick beeps every 60 seconds. The Remark states: Replace the unit immediately.

What is the Power Supply for the X-SENSE XC01?

The X-SENSE XC01 uses a 10-year sealed lithium battery.

What is the Product Lifespan for the X-SENSE XC01?

10 years.

What is the Sensor Type for the X-SENSE XC01?

Electrochemical.

What is the Safety Standard that the X-SENSE XC01 complies with?

EN 50291-1:2018.

What are the Operating Temperatures for the X-SENSE XC01?

4.4–37.8°C (40–100°F).

What is the Operating Relative Humidity for the X-SENSE XC01?

10%–85% RH (non-condensing).

What is the Alarm Loudness for the X-SENSE XC01?

≥ 85 dB at 3 m (10 ft) @ 3.2 ± 0.3 kHz pulsing alarm.

What are the Storage and Transport Conditions for the X-SENSE XC01?

-20–60°C (-4–140°F), 5%–95% RH (non-condensing).

What is the Silence Duration for the X-SENSE XC01?

About 9 minutes.

What are the immediate steps to take when the alarm sounds on the X-SENSE XC01?

1. Call emergency services as soon as possible.

2. Immediately move outside and make sure that everyone inside the house has evacuated the area or has access to fresh air. Do not re-enter the house until it has been aired out and your alarm remains under normal condition. If it is not possible to move outside, stay close to an open door/window until emergency service responders arrive.

What should be done if the alarm reactivates within a 24-hour period after following the initial steps when the X-SENSE XC01 alarm sounds?

After following steps 1-2 above, if your alarm reactivates within a 24 hour period, repeat steps 1-2 and call a qualified appliance technician to investigate sources of CO from fuel-burning equipment and appliances, and inspect for proper operation of this equipment.

What should be done if problems are identified during the CO source inspection after an X-SENSE XC01 alarm?

If problems are identified during this inspection, have the equipment serviced immediately. Note any combustion equipment that has not been inspected by the technician and consult the manufacturer’s instructions, or contact the manufacturers directly for more information about CO safety and this equipment. Make sure that motor vehicles are not, and have not been, operating in an attached garage or adjacent to the residence.

What are the steps to maintain the X-SENSE XC01 in good working order?

To keep your alarm in good working order, you should adhere to the following steps:

Test the alarm once a week by pressing the test/silence button.
Vacuum the alarm cover once a month to remove any accumulated dust.
Never use detergents or solvents to clean the alarm. Chemicals can permanently damage or temporarily contaminate the sensor.
Avoid spraying air fresheners, hair spray, paint or other aerosols near the alarm.
Do not paint the unit. Paint may clog the openings to the sensing chamber and prevent the unit from operating properly.