ROBOROCK SAROS 10 (03) PDF DOCUMENT

The ROBOROCK SAROS 10 robot vacuum consists of the following components:

Top View (A1):

A1-1: Bumper

A1-2: LiDAR Sensor

A1-3: Vertical Bumper

A1-4: Spot Clean Button

A1-5: Power/Clean Button

A1-6: Status Indicator Light

A1-7: Dock Button

A1-8: Top Cover

Bottom View (A2):

A2-1: Wall Sensor

A2-2 & A3-7 to A3-11: Cliff Sensors

A2-3: Omni-Directional Wheel

A2-4: Charging Contacts

A2-5: Side Brush

A2-6: Main Wheels

A2-7: Main Brush

A2-8: Main Brush Cover Latches

Rear View (A3):

A3-5: Dustbin Release Latch

A3-6: Air Outlet

Dustbin and Water Tank Module (A4):

A4-1: Filter

A4-2: Dustbin Latch

A4-3: Dustbin

A4-4: Water Tank

A4-5: Water Tank Stopper

Mop Module (A5):

A5-1: Mop Cloth

The ROBOROCK SAROS 10 docking station consists of the following components:

A7: Disposable Dust Bag

A10: Power Cable

A11-1: Dock Lid

A11-2: Dust Bag Holder

A11-3: Cable Tidy

A11-4: Dock Base

A11-5: Dock Location Beacon

A11-6: Air Inlet

A11-7: Charging Contacts

A11-8: Washing Strip

A11-9: High-Speed Maintenance Brush

A11-10: Maintenance Brush Latch

A11-11: Dirty Water Tank

A11-12: Water Tank Handle

A11-13: Clean Water Tank

A11-14: Water Tank Latch

A11-15: Status Indicator Light

A11-16: Water Outlet

A11-17: Dirty Water Inlet

A11-18: Power Socket

A11-19: Ramp

To ensure proper operation, place the docking station on a hard and level floor. Position it flat against a wall. Make sure there is ample space in front of and on both sides of the dock to allow the robot to return successfully. Avoid placing the dock in cluttered areas, tight corners, or on carpet.

Follow these steps to set up the docking station:

1. Place the dock base on a level floor against a wall (B2-1).

2. Securely attach the ramp to the front of the dock base (B2-2).

3. Connect the power cable to the power socket on the back of the dock (B2-3).

4. Plug the other end of the power cable into a wall outlet (B3-1).

5. Place the robot vacuum onto the dock to power it on and begin charging (B3-3).

To prepare for mopping, you need to fill the clean water tank:

1. Remove the Clean Water Tank from the docking station (D16-1).

2. Open the cap on the tank (D16-2).

3. Fill the tank with clean water (D16-3).

4. Securely close the cap and place the tank back into the docking station until it clicks into place (D16-4).

To clean the main brush, follow these steps:

1. Turn the robot vacuum upside down.

2. Press the two latches on the main brush cover to unlock and remove it (D1-5).

3. Lift the main brush out of the robot (D1-6).

4. Remove any tangled hair and debris from the brush and its bearings (D1-7).

5. Reinsert the main brush and securely clip the main brush cover back into place (D1-8).

Use a screwdriver to unscrew and remove the side brush. Clean off any tangled hair or debris, then screw the brush firmly back into place (D2).

Omni-Directional Wheel (Front Wheel):

1. Use a small tool to pry out the wheel and its axle (D3-1).

2. Rinse the wheel and axle with water to remove hair and dirt.

3. Reinstall the wheel by pressing it firmly back into place (D3-2).

Main Wheels:

Wipe the main wheels with a soft, dry cloth to remove any dust or debris (D4).

Follow these steps for cleaning the dustbin and filter:

1. Open the top cover of the robot and press the release latch to remove the dustbin/water tank module (D5-1).

2. Open the dustbin and empty its contents into a trash can (D5-2).

3. Remove the filter from the dustbin (D5-3).

4. Rinse the filter thoroughly under running water (D5-4).

5. Gently tap the filter to remove excess water (D6-1).

6. Allow the filter to air dry completely for at least 24 hours before reinstalling it (D6-2).

Use a soft, dry cloth to perform the following cleaning tasks:

1. Gently wipe all the sensors on the robot, including the cliff sensors on the bottom and the wall sensor on the side (D7-1, D7-2).

2. Wipe the charging contacts on the underside of the robot (D9-7).

3. Wipe the charging contacts on the docking station base (D9).

To clean the mop cloth, remove it from the mop mount (D8-1) and wash it as needed (D8-2).

Remove the Dirty Water Tank from the docking station, empty the collected dirty water, and place the tank back into its slot (D10).

Follow these steps to replace the dust bag:

1. Open the lid of the docking station.

2. Lift the dust bag up and out of the dock using its handle. The bag will seal itself upon removal.

3. Dispose of the old bag.

4. Slide a new dust bag down into the slot until you feel it click into place (D13).

To maintain the dock’s interior, perform the following cleaning tasks:

1. Dock Base and Washing Strip: Wipe the inside of the dock base and the washing strip with a soft cloth (D11). Do not pour water directly into the base.

2. Water Filter: Remove the water filter located inside the dock base at the dirty water inlet, rinse it under clean water, and reinstall it (D12).

3. Air Inlet: Wipe the air inlet located inside the dust bag compartment to ensure it is clear of debris (D14).

4. High-Speed Maintenance Brush: Press the latch to unlock and remove the maintenance brush (D15-1, D15-2). Clean the brush and its housing, then reinstall it and lock the latch (D15-3).