ROBOROCK Q7 M5+ (M5PLUS) FCC (02) PDF DOCUMENT

The main components of the ROBOROCK Q7 M5+ (M5PLUS) FCC robot vacuum and its accessories are:

Robot (Top View – A1)

A1-1: Power/Clean Button

A1-2: Dock/Spot Clean Button

A1-3: Lid Latch

A1-4: LiDAR Sensor

Robot (Bottom View – A2)

A2-1: Wall Sensor

A2-2: Cliff Sensors

A2-3: Omni-Directional Wheel

A2-4: Charging Contacts

A2-5: Side Brush

A2-6: Main Wheels

A2-7: Main Brush Cover

Dustbin (A3)

A3-1: Dustbin Release Latch

A3-2: Filter Cover Latch

A3-3: Filter

Water Tank (A4)

A4-1: Water Tank Latch

A4-2: Water Filter

A4-3: Mop Cloth Mount Slot

A4-4: Fill Port

Mop Cloth Mount (A5)

A5-1: Mop Cloth

Power Cable (A6)

Auto-Empty Dock (A7, A8, A9)

A7-1: Dock Lid

A7-2: Dock Status Indicator Light

A7-3: IR Emitter

A8-1: Cable Outlet

A8-2: Power Port

A8-3: Air Inlet

A8-4: Dock Base Screws

A9-1: Dust Bag

A9-2: Air Inlet Filter

A9-3: Air Outlet Filter

To position the Auto-Empty Dock correctly, follow these steps:

1. Place the dock on a hard and flat floor, against a wall.

2. Ensure there is at least 0.5 m (1.6 ft) of clearance on both sides of the dock.

3. Ensure there is at least 1.5 m (4.9 ft) of clearance in front of the dock.

4. Connect the power cable to the dock and plug it into a wall outlet.

5. If you have wooden floors, place the waterproof mat under the dock.

Place the robot vacuum onto the Auto-Empty Dock. The robot will power on automatically and begin charging. The power indicator light on the robot will breathe to indicate it is charging.

Follow these steps to install the mopping system:

1. Press the latch to remove the water tank from the robot.

2. Open the fill port, fill the tank with water, and close it securely.

3. Slide the Mop Cloth Mount along the bottom of the water tank until it clicks into place.

4. Reinstall the water tank assembly into the robot until you hear it click.

1. Turn the robot over and press the latches to remove the main brush cover.

2. Pull out the main brush.

3. Remove and clean any hair or debris from the main brush and its bearings.

4. Reinsert the main brush and clip the main brush cover back into place.

Unscrew the side brush, remove it, clean any tangled hair or debris, and then screw it back into place.

Omni-Directional Wheel:

1. Use a tool, such as a small screwdriver, to pry out the axle and remove the wheel.

2. Rinse the wheel and the axle with water to remove any hair and dirt.

3. Air dry and reinstall the wheel, pressing it firmly back into place.

Main Wheels:

Wipe the main wheels with a soft, dry cloth to remove any debris.

1. Open the robot’s top cover and remove the dustbin/water tank unit.

2. Open the filter cover latch on the dustbin and remove the filter.

3. Rinse the filter repeatedly under clean water.

4. Allow the filter to dry completely for at least 24 hours before reinstalling it.

1. Remove the Mop Cloth Mount from the water tank.

2. Peel the mop cloth off the mount.

3. Clean the mop cloth with water and allow it to air dry.

1. Lift and remove the lid of the Auto-Empty Dock.

2. Lift the dust bag vertically out of the dock.

3. Discard the used dust bag.

4. Insert a new disposable dust bag, ensuring it is seated correctly.

5. Replace the dock lid.