PYLE PLMRB39W (01) PDF Document

The PYLE PLMRB39W features include:

• AM/FM/MP3/USB/AUX/SD Card Reader Marine Stereo Receiver

• Single DIN

• LCD Display with Remote Control

• Marine Stereo Receiver System

• AM/FM Stereo Radio, 30 Station Memory

• Wireless BT Streaming Audio Ability

• USB Flash & SD Memory Card Readers

• Aux (3.5mm) Input Connector Jack

• Connect and Stream Audio from External Devices

• MP3 Digital Audio File Playback

• LCD Display Panel

• USB/SD Card Reader

• Electronic Volume Control (10EQ, Balance, Fader)

• Memory/Repeat/Random/Intro Play

• Mute/Clock Control

• ID3 Tag Song Readout for Artist Name/Song Title

• RGB Button Control

• 1 pair RCA Output + 2x Subwoofer

• Equalizer (EQ) Electronic Audio Configuration

• Automatic Memory Preset Store/Scan Mode

• Repeat/Shuffle Song Functions

• Compatible With XBass, Siri Dialing, Android App, IOS App & Demo Mode

The Wireless BT Connectivity features for the PYLE PLMRB39W are:

• Built-in Wireless BT Music Streaming

• Built-in Microphone for Hands-Free Calling

• Conveniently Reject/Answer Incoming Calls

• Compatible with All of Your Favorite Bluetooth Devices (iPhone, Androids, Smartphones, iPad, Tablets, etc.)

• Wireless BT Version: BT VERSION 4.2

The technical specifications for the PYLE PLMRB39W are as follows:

• Remote Control Battery Operated, Requires (1) Coin-Type Battery

• Battery Type: 3V Lithium Bat. 240mAh Capacity

• Single DIN Universal Size Standard

• Night illumination: RGB

• Power Output: 100 Watts (4×25)

• PLL Electronic Tuning Radio Tuner

• ISO with 4 Pin/8 Pin Wire Connector

• Stereo/Mono Mode Selectable

• Audio Control: 10EQ/Fader/Balance, No Treble & Bass

• Preset EQ: Flat/Pop/Rock/Class/OFF

• Switchable USA/Europe Tuner Frequencies by Software

• Max. USB/SD Memory Support: 64GB

• Power: DC 12V

• Current Consumption: 10A

• Product Dimension: 4.5″ x 7.1″ x 1.97″ – inches

Follow these steps to install the PYLE PLMRB39W:

1. Lift the left or right top corner of the plastic outer trim ring, then pull it out to remove it.

2. Insert the two bracket keys into the left and right sides of the chassis to separate the chassis from the housing.

3. Install the mounting sleeve on the board. Check the opening size of the sliding panel to be mounted. If the opening is not large enough, carefully cut it until it fits easily. Locate the series of mounting tabs above, below, and on all sides of the sleeve. Completely insert it into the opening of the board, and bend the tabs as necessary outward to ensure it fits the board.

4. Slide the stereo into the opening in the dash, ensuring that the wires behind it are tucked in and not pinched.

5. Follow the wiring diagram carefully. Verify that you’ve connected them correctly. CAUTION! Connect the unit to a 12-volt power source with adequate grounding.

6. Attach the front panel and turn on the unit (the vehicle must be switched on). If the unit does not work, check the connections again until the problem is solved. With the new car stereo secured into the bracket, plug the wiring harness back into the stereo.

7. Slide the stereo into the opening in the dash again, ensuring that the wires behind it are tucked in and not pinched. Tuck the wires back into the opening behind the unit.

8. Install the plastic outer trim ring.

9. Snap all the pieces of trim back into place over the stereo. Double-check that all screws and trim pieces are securely in place. Test the new stereo and its settings.

1. Power/MODE (source) button

2. SEL (select/menu) button and VOL (volume) knob

3. Back to the previous configuration point; Press /Bass enhances the pulse function

4. MUTE button / DISP (CLK) button: In power-on mode, press to toggle mute ON or OFF.

5. ►II (Pause/Start), Button 1 preset station

6. INT (intro), Station preset button 2

7. RPT (repeat), Button 3 preset

8. RDM (random), Button 4 preset

9. -10 (10 previous songs), Preset station 5 button

10. +10 (10 following songs), Preset station 6 button

11. Phone button

12. |◄◄ (Tune back, search back, crawl back, fast reverse)

13. ►►| (Tune forward, search forward, crawl forward, fast forward)

14. Release button cover

15. IR remote control sensor

16. LCD screen

17. BAND (band) button/AS (automatic storage/preset station search)

18. USB/SD port

19. AUX IN (auxiliary input)

20. MIC hole (integrated microphone)

Turn Unit ON/OFF:

• Press the power/MODE button on the front panel to turn ON the unit, and press and hold it again to turn OFF the unit.

• Press the power button on the remote control to turn the unit ON or OFF.

Adjust Volume (VOL):

• Rotate the VOL knob on the front panel or press the VOL+ / VOL- buttons on the remote control to increase or decrease the volume level.

Adjust Menu Options (SEL):

• Press the SEL button on the front panel or on the remote control repeatedly to navigate through the audio functions: BASS, TREBLE, BALANCE, FADER, EQ OFF, CLASS, etc.

Press the SEL button repeatedly to cycle through the menu. To adjust a setting, turn the VOL knob on the front panel or press the VOL+/VOL- buttons on the remote.

• SWE (subwoofer): Press the SEL button to select SWE, then rotate the knob to select ON/OFF.

• 10EQ Control: Press the SEL button, then press the BAND button to enter the 10EQ control mode. Press the BAND button to select the EQ volume, then turn the volume knob to adjust the EQ level.

• BALANCE: L7, L6, ~, L1, 0, R1, ~, R6, R7

• FADER: R7, R6, ~, R1, 0, F1, ~, F6, F7

• EQ: Set to OFF, CLASS, ROCK, POP, FLAT, JAZZ, COUNTRY.

• Loudness: LOUD ON/OFF.

• DX/LOCAL: Enables or disables the local broadcast mode (LOCAL).

• Stereo/Mono: Change the reception mode to STEREO or MONO in Radio mode.

• CLOCK 12/24: Changes the clock format between 12-hour and 24-hour.

• Button Lighting Color: Preset as blue, red, cyan, green, purple, yellow, white, or Auto (color changes automatically).

1. To display the time, press the CLK button.

2. To set the time, press and hold the CLK button, and the time will start flashing.

3. Press the |◄◄ or ►►| button on the front panel or on the remote control to set the hour.

4. Press the CLK button, and the minutes will start flashing.

5. Press the |◄◄ or ►►| button on the front panel or on the remote control to set the minutes.

Press the MODE button to switch between RADIO, BT (Bluetooth), USB (with a USB device inserted), SD (with an SD card inserted), and AUX-IN mode (auxiliary input).

Change Bands (BAND): Press the BAND button to switch between the FM1, FM2, FM3, AM1, and AM2 bands. Each band stores up to six preset stations.

Manual Tuning: Press and hold the |◄◄ or ►►| button on the front panel or remote to enter manual tuning mode. In this mode, press the |◄◄ or ►►| button to move the radio frequency up or down one step.

Auto Seek Tuning: In standby mode, quickly press the |◄◄ or ►►| button to move to the next/previous available station automatically.

To Store/Recall Preset Stations: The radio can store 6 preset stations for each band (FM1, FM2, FM3) for a total of 18 preset stations.

Memorize a Station:

1. Turn the radio on and select the desired band and station.

2. Select a station using the |◄◄ or ►►| button.

3. Press and hold the desired preset button (numbered 1-6 on the face of the radio) for more than 2 seconds to save the station to that preset number.

To Recall a Preset Station:

1. Select the desired band.

2. Briefly press a preset button (numbered 1-6) to recall the corresponding preset station.

Automatic Store Station/Preset Station Scan (AMS): Press and hold the AMS button for more than 2 seconds to select six strong stations and store them in the current band. The radio will automatically scan the current frequency and enter the six strongest stations into the preset memory positions for that band. Briefly press the AMS button on the remote control to recall each preset station saved in the memories in each band.

LOCAL/DX: In urban areas, most stations are strong, and “LOCAL ON” mode should be selected. Switch to LOCAL OFF mode to search for stations with weaker signals. Press the LOC button on the remote control to choose local or distant reception mode.

STEREO/MONO: FM stations are received in stereo mode. If the signal is weak, switching to MONO mode usually improves the overall sound quality. Press the ST button on the remote control to choose FM STEREO or MONO audio effect.

Insert USB/SD Card: To play files from a USB/SD device, open the USB/SD port cover and insert the device into the port. The songs will begin to play automatically.

Eject USB/SD: To eject a USB device, press the ►II button to stop playback, then remove the device. To eject an SD card, press the ►II button to stop playback, press the release button to remove the front panel, then remove the SD card from the chassis.

Play/Pause: Press the ►II (play/pause) button to pause or resume playback.

Next/Previous Track: Press the ►►| button to play the next track. Press the |◄◄ button to play the previous track.

Fast Forward/Backward: Press and hold the ►►| button to fast forward. Press and hold the |◄◄ button to fast backward.

Introduction Scan: Press the INT button to play the first 10 seconds of each track. Press again to stop the scan and play the current track.

Repeating the Same Track: Press the RPT button to repeat the current track. Press again to stop repeat playback and resume normal playback.

Playing All Tracks in Random: Press the RDM button to play all tracks in random order. Press again to cancel this function.

Track/Folder Navigation:

• During USB or SD card mode, press the 5/-10 button to go backward 10 tracks. Press the 6/+10 button to jump forward 10 tracks.

• During MP3 playback, press and hold the 5/-10 button to go back to the previous folder. Press and hold the 6/+10 button to go to the next folder. This function depends on the number and level of folders.

• These buttons do not function if the USB or SD card has no folders.

a. Press and hold the AMS button to directly select a music file. “TRK0000” will appear on the display.

b. Turn the volume control to select the first digit. Then press the |◄◄ button to move the digit to the left and enter the next digit.

c. When the desired track number appears, confirm your selection by pressing the SEL button.

This receiver has an external auxiliary input jack (3.5mm) on the front panel. Plug a player like an MP3 player into the AUX IN jack using a 3.5mm stereo audio cable. Press the MODE button to switch to AUX input mode. “AUX IN” will appear on the display. You can then listen to music from the external device through the speakers. Remember to adjust the volume of the external device to a comfortable level.

1. Before pairing, the BT logo on the LCD will indicate that no device is connected. To begin, enable BT mode on your mobile phone.

2. When your phone finds the car audio system, the name “PYLE” will be displayed.

3. Choose “PYLE” from the device list to pair and connect. Upon confirming, the BT logo will stop flashing.

4. Once pairing is complete, your mobile phone audio will automatically transfer to the car audio system whenever a call is made or received, or when the phone plays music.

Make a Call:

• Dial the number directly from your paired mobile phone.

• To use the hands-free system: Press the phone button to access dial mode, use the “0~9,” * and # buttons on the remote to enter the number, then press the phone button to make the call. If you enter a number incorrectly, press the DEL button on the remote to delete it.

Redial Last Dialed Number: Press and hold the phone button on the control panel to redial the last dialed phone number.

Answer a Call: When your phone receives a call, the incoming number displays on the LCD. To answer, press the phone button on the control panel.

Reject or End a Call: To reject an incoming call or end an ongoing call, press the end call button on the control panel.

Switch Audio Between Car Audio and Mobile Phone: During a call, press the VOL knob button to switch the audio source from the car audio system back to your mobile phone.

Adjust Talk Volume: During a call, use the VOL knob or VOL+/VOL- buttons to adjust the volume. Use the MUTE button to mute the sound.

1. Press the /MODE button to enter BT mode, and the display will show “Pause” on the LCD.

2. When a mobile device is paired, music played through that device will automatically be heard through the car audio system.

3. Press the |◄◄ or ►►| button to play the next or previous track on the mobile phone.

4. Press the ►II button to pause or resume music playback.

1. Power ON/OFF Button: Switches ON/OFF.

2. VOL +/VOL-: Volume Up/Down.

3. Band button (Reply call).

4. |◄◄ Button: Tune down, seek down; Track down, fast reverse.

5. SEL (Selection) button.

6. ►►| Button: Tune up, seek up; Track up, fast forward.

7. Mute button, DEL (Delete) button.

8. CLK (Clock setting) button (End call) button.

9. ►II Button, preset station 1 button, keypad 1.

10. INT (Intro) button, preset station 2 button, keypad 2.

11. RPT (Repeat) button, preset station 3 button, keypad 3.

12. RDM (Random), preset station 4 button, keypad 4.

13. -10 (Previous 10 tracks), preset station 5 button, keypad 5.

14. +10 (Next 10 tracks), preset station 6 button, keypad 6.

15. ST (Stereo) button, keypad 7.

16. LOUD (Loudness) button, keypad 8.

17. AMS (Automatic Music Search) button, keypad 9.

18. MODE button, keypad *.

19. EQ (Equalizer) button, keypad 0.

20. LOC (Local)/DX button, keypad #.

Remove Insulating Sheet: The remote control comes with an insulating sheet attached to the underside. The remote will not work until this sheet is removed.

Replace Lithium Battery Cell:

1. When the lithium cell battery becomes weak, replace it.

2. Press and hold the movable block in the direction indicated by arrow 1. At the same time, pull the cell holder out of the remote in the direction indicated by arrow 2.

3. Replace the old cell with a new one, ensuring the (+) polarity is facing upward.

4. Reinsert the cell holder into the remote control.

If your PYLE PLMRB39W does not turn on, check the following:

1. Vehicle’s engine switch is not on: Turn your Vehicle’s key to ACC or ON.

2. Cable is not correctly connected: Check the connection.

3. Fuse is burnt: Replace the fuse.

No Sound:

• Volume is in mute or minimum: Check the volume or mute ON/OFF status, and adjust the volume to the desired level.

Sound skips:

• The installation angle is more than 30°: Adjust the installation angle to less than 30°.

The built-in micro-computer may not be operating properly due to noise. Press the RESET button to restore the program to zero. The RESET button is accessible after removing the front panel.

1. Much noise in broadcasts:

The station or signal is too weak. Select other stations with stronger signal levels.

2. The antenna cable is not connected:

Insert the antenna cable firmly into the antenna socket of this receiver.

3. Preset station is reset:

The battery cable is not correctly connected. Connect the battery cable to the terminal that is always live.

This feature allows you to access SIRI or GOOGLE voice via Wireless BT.

• Your phone must support SIRI or GOOGLE voice.

• Once connected to BT, your phone will ask for access to your contact list.

• You are now ready to use PUSH-TO-TALK. Press the PUSH-TO-TALK icon. You are ready to talk. Say, “Call (CONTACT NAME)” and the system will call without you needing to use your phone.

NOTE: Samsung “S” Voice and other associated apps are not compatible.