PYLE PDWM1958B (01) PDF DOCUMENT

To ensure proper setup and avoid interference with your PYLE PDWM1958B system, please follow these tips:

1. Each unit may have many presented channels. To avoid interference, each unit should use a different channel, especially when using multiple receivers and transmitters together.

2. The transmitter and receiver antenna should be kept in a barrier-free, linear relative position.

3. Do not place the receiver close to a metal surface or any digital equipment.

4. Try to keep the receiver 1.5 meters above the floor and 1 meter away from the wall for best performance.

The contents are for the whole system, the actual components for your PYLE PDWM1958B may differ. The possible components include:

1. Wireless receiver

2. Adapter (optional)

3. Adapter (optional)

4. Cable (optional)

5. Charging cable (optional)

6. AA batteries (optional)

7. 14500 lithium battery (optional)

8. User manual (Optional)

9. Handheld transmitter (optional)

10. Body pack transmitter (optional)

11. Lavalier microphone (optional)

12. Headset mic (optional)

13. 6.35″ signal output cable

The receiver for the PYLE PDWM1958B system has the following parts:

1. Power Switch

2. VOL. A (Volume for Channel A)

3. VOL. B (Volume for Channel B)

4. RF Signal Lamp

5. AF Signal Lamp

6. Power Signal Lamp

7. LCD Display

8. 1/4 Audio Output Socket

9. XLR Audio Output Socket

10. Power Input Socket

11. Charging Socket

12. ANT-A / ANT-B (Antennas)

The handheld transmitter for the PYLE PDWM1958B system has the following parts:

1. Power signal lamp

2. LED display

3. Battery Cover

4. Frequency-change button

5. Power switch

The body pack transmitter for the PYLE PDWM1958B system has the following functions:

1. Clip microphone socket

2. LED light

3. Antenna

4. LED display

5. Frequency-change button

6. Power switch

To match the receiver and transmitter for your PYLE PDWM1958B, follow these steps:

1. Make sure the receiver is powered OFF.

2. On the transmitter, press and hold the frequency-change button, then press and hold the power button until the transmitter’s display starts flashing.

3. Turn ON the receiver. You will see the RF light on the receiver start flashing.

4. Attention: For receivers that have an LED display, turn ON the receiver and wait for 3-5 seconds.

5. Return to the transmitter and press the frequency-change button again (a single press).

6. The matching is successful if the RF light on the receiver is solid ON or the LED display on the receiver shows the frequency. If not, please repeat steps 1 through 5.

Connect the connector of the supplied lavalier microphone to the connecting jack on the bodypack transmitter. This will set the transmitter to work in a wireless lavalier system configuration.

Connect the connector of the supplied headset microphone to the connecting jack on the bodypack transmitter. This will set the transmitter to work in a wireless headset system configuration.

Some models support charging. Use the provided charging cable to connect the microphone to the charging socket on the receiver.

CAUTION: For charging the microphone, you MUST NOT use an AA battery. You MUST use a 14500 lithium battery to power the microphone.

To use multiple systems together and prevent interference, follow these guidelines:

1. Ensure that each transmitter is matched to its corresponding receiver. Refer to the “Matching receiver and transmitter” procedure.

2. Use a different frequency for each transmitter/receiver pair. The frequency difference between each system should be 3-4MHz.

If you are experiencing no sound or weak sound, check the following:

1. If the transmitter display or light is off: Turn on the transmitter, make sure the battery is installed correctly, or replace the batteries.

2. If the receiver display or light is off: Make sure the adapter is plugged into the receiver’s DC socket and that the adapter has power.

3. If the receiver display or light indicates an RF signal is present: Turn up the receiver volume and check the cable connection of the receiver.

4. If the receiver display or light indicates no RF signal, but the transmitter and receiver power lights are on: Remove the receiver away from metal objects, check for barriers between the receiver and transmitter, and try re-matching the receiver and transmitter.

If you experience distortion or unwanted noise while the receiver display or light indicates an RF signal, try these solutions:

1. Remove any interference sources that are nearby.

2. Change the working frequency of both the receiver and transmitter.

3. Replace the batteries in the transmitter.

4. If you are using many sets together, increase the working frequency interval between the systems.

5. Maximize the volume button.

If the transmitter fails to turn on or shuts down immediately after pressing the power button, please try the following:

1. Replace the batteries.

2. Re-press the power button after a few seconds.

Please note that some specifications may not apply to all models.

RECEIVER

Channels: 16 Channels

SNR: 96db

Sensitivity: 96dbm

Frequency Response: 30~20kHz

Channel Interval: 500kHz

Output Impedance: 600 Ohm

Power Supply: 5V

Power Consumption: <85Ma

LED Display

HANDHELD TRANSMITTER

Power Output: 10dbm

Frequency Response: 30kHz~20kHz

Power Supply: 3V (Normal battery)

Power Supply: 3.7V (Lithium battery)

BODYPACK TRANSMITTER

Power Output: 10dbm

Frequency Response: 30kHz~20kHz

Power Supply: 3v