Free English PYLE PDWM1950 (01) PDF Document. Free English PYLE PDWM1950 (01) PDF User Guide. Free English PYLE PDWM1950 (01) PDF User Manual. Free English PYLE PDWM1950 (01) PDF Owner Guide. Free English PYLE PDWM1950 (01) PDF Owner Manual. Free English PYLE PDWM1950 (01) PDF Reference Guide. Free English PYLE PDWM1950 (01) PDF Instruction Guide. Free English PYLE PDWM1950 (01) PDF Reference Manual. Free English PYLE PDWM1950 (01) PDF Instruction Manual. Free English PYLE PDWM1950 (01) PDF Operating Instructions.
CLICK HERE TO DOWNLOAD PYLE PDWM1950 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What are the setup tips for the PYLE PDWM1950 to avoid interference?
To set up the PYLE PDWM1950 system and avoid interference, please follow these tips:
• To avoid interference, each unit may have many presented channels. When using multiple receiver/transmitter sets together, ensure each set uses a different channel.
• The transmitter and receiver antenna should be kept in a barrier-free, linear relative position.
• Do not place the receiver close to metal surfaces or digital equipment.
• Try to keep the receiver at least 1.5 meters above the floor and 1 meter away from any walls.
What are the components of the PYLE PDWM1950 receiver?
The components of the PYLE PDWM1950 receiver are as follows:
1. Power Switch
2. VOL. A (Volume for Channel A)
3. VOL. B (Volume for Channel B)
4. RF Signal Lamp
5. AF Signal Lamp
6. Power Signal Lamp
7. LCD Display
8. 1/4 Audio Output Socket
9. XLR Audio Output Socket
10. Power Input Socket
11. Charging Socket
12. ANT-A (Antenna for Channel A)
What are the parts of the PYLE PDWM1950 handheld transmitter?
The parts of the PYLE PDWM1950 handheld transmitter (microphone) are:
1. Power signal lamp
2. LED display
3. Battery Cover
4. Frequency-change button
5. Power switch
What are the functions of the PYLE PDWM1950 bodypack transmitter?
The functions of the PYLE PDWM1950 bodypack transmitter are as follows (note: only applies to some models):
1. Clip microphone socket
2. LED light
3. Antenna
4. LED display
5. Frequency-change button
6. Power switch
How do I match the receiver and transmitter for my PYLE PDWM1950 system?
To match the receiver and transmitter for your PYLE PDWM1950, please follow these steps (note: this may only apply to some models):
1. Make sure the receiver is powered OFF.
2. On the transmitter, press and hold the frequency-change button, then press and hold the power button until the display starts flashing.
3. Turn ON the receiver. You should see the RF light on the receiver start flashing.
4. Attention: For receivers that have an LED display, turn ON the receiver and wait for 3-5 seconds.
5. Return to the transmitter and press the frequency-change button again (a single press).
6. Matching is successful if the RF light on the receiver turns solid (stops flashing) or the LED display shows the frequency. If not, please repeat steps 1 through 5.
CLICK HERE TO DOWNLOAD PYLE PDWM1950 (01) PDF DOCUMENT