PYLE PLMRK47BK (01) PDF Document

The PYLE PLMRK47BK marine stereo receiver includes the following features:

• AM/FM/MP3/USB/AUX/SD Card Reader Marine Stereo Receiver

• Single DIN

• LCD Display with Remote Control

• Marine Stereo Receiver System

• AM/FM Stereo Radio, 30 Station Memory

• Wireless BT Streaming Audio Ability

• USB Flash & SD Memory Card Readers

• Aux (3.5mm) Input Connector Jack

• Connect and Stream Audio from External Devices

• MP3 Digital Audio File Playback

• LCD Display Panel

• USB/SD Card Reader

• Electronic Volume Control (10EQ, Balance, Fader)

• Memory/Repeat/Random/Intro Play

• Mute/Clock Control

• ID3 Tag Song Readout for Artist Name/Song Title

• RGB Button Control

• 1 pair RCA Output + 2x Subwoofer

• Equalizer (EQ) Electronic Audio Configuration

• Automatic Memory Preset Store/Scan Mode

• Repeat/Shuffle Song Functions

• Compatible With XBass, Siri Dialing, Android App, iOS App & Demo Mode

• Built-in Wireless BT Music Streaming

• Built-in Microphone for Hands-Free Calling

• Conveniently Reject/Answer Incoming Calls

• Compatible with all of your favorite Bluetooth devices (iPhone, Androids, Smartphones, iPad, Tablets, etc.)

• Wireless BT Version: BT VERSION 4.2

• Remote Control Battery Operated, Requires (1) Coin-Type Battery

• Battery Type: 3V Lithium Bat. 240mAh Capacity

• Single DIN Universal Size Standard

• Night illumination: RGB

• Power Output: 100 Watts (4×25)

• PLL Electronic Tuning Radio Tuner

• ISO with 4 Pin/8 Pin Wire Connector

• Stereo/Mono Mode Selectable

• Audio Control: 10EQ/Fader/Balance, No Treble & Bass

• Preset EQ: Flat/Pop/Rock/Class/OFF

• Switchable USA/Europe Tuner Frequencies by Software

• Max. USB/SD Memory Support: 64GB

• Power: DC 12V

• Current Consumption: 10A

• Product Dimension: 4.5″ x 7.1″ x 1.97″ – inches

1. Lift the left or right top corner of the plastic outer trim ring, then pull it out to remove it.

2. Insert the two bracket keys into the left and right sides of the chassis to separate the chassis from the housing.

3. Install the mounting knob on the board. Check the opening size of the sliding panel to be mounted. If the measurement is not large enough, carefully cut it until it fits easily into the opening. Do not force the handle into the opening to avoid bending it. Locate the series of mounting tabs above, below, and on all sides to be mounted. Completely insert it into the opening of the board, and bend the tabs as necessary outward to ensure it fits the board.

4. Slide the stereo into the opening in the dash, ensuring that the wires behind it are tucked in and not pinched.

5. Follow the wiring diagram carefully. Verify that you’ve connected them correctly. CAUTION! Connect the unit to a 12-volt power source with adequate grounding.

6. Now that your wires are all connected, attach the front panel and turn on the unit (the vehicle must be switched on). If the unit does not work, check the connections again until the problem is solved. With the new car stereo secured into the bracket, all you need to do is plug the wiring harness back into the stereo and put the assembly back into place.

7. Slide the stereo into the opening in the dash, ensuring that the wires behind it are tucked in and not pinched. This may take a few attempts if the vehicle has a tight dash opening. Tuck the wires back into the opening behind the unit.

8. Install the plastic outer trim ring.

9. Snap all the pieces of trim back into place over the stereo. Double-check that all screws and trim pieces are securely in place. Try out the new stereo by turning the car power on again and experimenting with the stereo and its settings to ensure everything is in working order.

1. Power / MODE (source) button

2. SEL (select/menu) button and VOL (volume) knob

3. Back to the previous configuration point. Pressing the Bass button enhances the pulse function.

4. In power-on mode, press the MUTE button to toggle mute ON or OFF / DISP (CLK) button.

5. ►II (Pause/Start), Button 1 preset station

6. INT (intro), Station preset button 2

7. RPT (repeat), Button 3 preset

8. RDM (random), Button 4 preset

9. -10 (10 previous songs), Preset station 5 button

10. +10 (10 following songs), Preset station 6 button

11. Phone button

12. K◄ (Tune back, search back, crawl back, fast reverse)

13. ►►I (Tune forward, search forward, crawl forward, fast forward)

14. Release button cover

15. IR remote control sensor

16. LCD screen

17. BAND (band) button/AS (automatic storage/preset station search, automatic search)

18. USB/SD port

19. AUX IN (auxiliary input)

20. MIC hole (integrated microphone)

• To turn the unit ON, press the power/MODE button on the front panel.

• To turn the unit OFF, press and hold the power/MODE button on the front panel.

• You can also press the power button on the remote control to turn the unit ON or OFF.

Rotate the VOL knob on the front panel or press the VOL+ / VOL- buttons on the remote control to increase or decrease the volume level.

Press the SEL button on the front panel or on the remote control repeatedly to navigate through the audio functions. Turn the VOL knob on the front panel or press the VOL+/- buttons on the remote control to set the selected item. The available functions are:

• **BASS/TREBLE/BALANCE/FADER**

• **SWE (subwoofer):** Press SEL to select SWE, then rotate the knob to select ON/OFF.

• **10EQ control mode:** Press the SEL button, then press the BAND button to enter. Press the BAND button again to select the EQ volume, then turn the volume knob to adjust the EQ level.

• **EQ:** Set to OFF, CLASS, ROCK, POP, FLAT, JAZZ, COUNTRY.

• **Loudness:** LOUD ON/OFF.

• **DX/LOCAL:** Enables or disables the local broadcast mode (LOCAL).

• **Stereo/Mono:** Change the reception mode to STEREO or MONO in Radio.

• **CLOCK 12/24:** Changes the clock format between 12-hour and 24-hour.

• **Button lighting color:** Preset as blue, red, cyan, green, purple, yellow, white, or Auto (the color changes automatically one by one).

1. To display the time, press the CLK button.

2. To set the time, press and hold the CLK button, and the time will start flashing.

3. Press the K◄ or ►►I button on the front panel or on the remote control to set the hour.

4. Press the CLK button, and the minutes will start flashing.

5. Press the K◄ or ►►I button on the front panel or on the remote control to set the minutes.

Press the MODE button to switch between RADIO, BT (Bluetooth), USB (with a USB device inserted), SD (with an SD card inserted), and AUX-IN mode (auxiliary input).

In power-on mode, briefly press the MUTE button to mute or resume sound. The mute state will be released when the volume knob is adjusted.

Press the LOUD button on the remote control to increase the loudness and boost the bass output frequency. Press it again to turn it off.

Press the EQ button on the front panel or on the remote control to switch between EQ settings: OFF, CLASS, ROCK, POP, and FLAT.

The RESET button is used to reset all factory settings and parameters. This function can be used when the LCD screen does not work properly, if the sound is distorted, or when some of the controls are disabled. To reset, press the RELEASE button to release the front panel and remove it, then use a thin object with a small tip to press the RESET button.

• **Change Bands (BAND):** Press the BAND button to switch between the FM1, FM2, FM3, AM1, and AM2 bands. Each band stores up to six preset stations.

• **Manual Tuning:** Press and hold the K◄ or ►►I button to enter manual tuning mode. In manual tuning mode, press the K◄ or ►►I button to move the radio frequency number up or down one step.

• **Auto Seek Tuning:** In standby mode or while not in manual tuning mode, quickly press the K◄ or ►►I button to move to the next/previous available station automatically.

**To Memorize a Station:**

1. Turn the radio on and select the desired band and station.

2. Select a station using the K◄ or ►►I button.

3. Press and hold the desired preset button (numbered 1-6 on the face of the radio) for more than 2 seconds to save the station to that preset number.

**To Recall a Preset Station:**

1. Select the desired band.

2. Briefly press a preset button (numbered 1-6) to recall the corresponding preset station.

**Automatic Store Station/Preset Station Scan (AMS):**

Press and hold the AMS button for more than 2 seconds to select six strong stations and store them in the current band. The radio will automatically scan the current frequency and enter the six strongest stations into the preset memory positions for that band. Briefly press the AMS button on the remote control to recall each preset station saved in the memories in each band.

• **LOCAL/DX:** In urban areas, most stations are strong enough, and “LOCAL ON” mode should be selected. Switch to LOCAL OFF mode to search for stations with weaker signals. Press the LOC button on the remote control to choose local or distant reception mode.

• **STEREO/MONO:** FM stations are received in stereo mode. However, if the signal is weak or reception is not as good as desired, switching to MONO mode usually improves the overall sound quality. Press the ST button on the remote control to choose FM STEREO or MONO audio effect.

• **Insert USB/SD Card:** To play files from a USB/SD device, open the USB/SD port cover and insert the USB/SD device into the port. The songs will begin to play automatically.

• **Eject USB/SD:** To eject a USB device, press the ►II button to stop playback, then remove the USB device. To eject an SD card, press the ►II button to stop playback, press the button to release and remove the front panel, then remove the SD card from the chassis.

• **Play/Pause:** Press the ►II (play/pause) button to pause or resume playback.

• **Next/Previous Track:** Press the ►►I button for the next track, and the K◄ button for the previous track.

• **Fast Forward/Backward:** Press and hold the ►►I button to fast forward. Press and hold the K◄ button to fast backward.

• **Introduction Scan:** Press the INT button to play the first 10 seconds of each track. Press again to stop.

• **Repeating:** Press the RPT button to repeat the current track. Press again to stop repeat playback.

• **Random Play:** Press the RDM button to play all tracks in random order. Press again to cancel.

• **Track Navigation:** During disc, USB, or SD card mode, press the 5/-10 button to go backward 10 tracks. Press the 6/+10 button to jump forward 10 tracks.

• **Folder Navigation:** During MP3 disc, USB, or SD card mode, press and hold the 5/-10 button to go back to the previous folder. Press and hold the 6/+10 button to go to the next folder. This function depends on the number and level of folders. These buttons do not function if the device has no folders.

• **Select a Specific Track (MP3 Format):**

a. Press and hold the AMS button to directly select a music file. “TRK0000” will appear on the display.

b. Turn the volume control to select the first digit. Then press the K◄ button to move the digit to the left and enter the next digit.

c. When the desired track number appears, confirm your selection by pressing the SEL button.

This receiver is equipped with an external auxiliary input jack (3.5mm) on the front panel. Plug a player like an MP3 player into the AUX IN jack using a 3.5mm stereo audio cable and press the MODE button to switch to AUX input mode. “AUX IN” will appear on the display. You can then listen to music from the external device through the speakers. Note: Adjust the volume of the external device to a comfortable level using the receiver’s volume control.

1. In any mode, prior to pairing and connecting, the BT logo on the LCD indicates that no device is connected. To begin pairing, enable BT mode on your mobile phone.

2. When the phone finds this audio system, the name “PYLE” will be displayed.

3. Choose “PYLE” from the device list to pair and connect with this audio system. Upon confirming, the BT logo will stop flashing.

4. When pairing is complete, the mobile phone audio will automatically transfer to the audio system whenever a call is made or received, or when the mobile phone plays music.

• **Make a Call:** You can dial the number directly from the paired mobile phone. Alternatively, when linked, press the phone button to access the dial telephone number mode. Use the “0~9,” * and # buttons on the remote control to input the telephone number. If a number is entered incorrectly, press the DEL button to delete it. Press the phone button to make the outgoing call.

• **Redial Last Dialed Number:** Press and hold the phone button on the control panel to redial the last dialed phone number.

• **Answer a Call:** When the mobile phone receives a call, the incoming telephone number displays on the LCD. To answer the call, press the phone button on the control panel.

• **Reject or End a Call:** To reject or end the call, press the end call button on the control panel.

• **Switch Audio:** During a call, press the VOL knob button to switch the audio source from the car audio system back to your mobile phone.

• **Adjust Talk Volume:** During a call, use the VOL knob or VOL+/- buttons to adjust the volume level. Use the MUTE button to mute the sound.

1. Press the power/MODE button to enter BT mode, and the display will show “Pause” on the LCD.

2. When a mobile device is paired, music played through that device will automatically be heard through the car audio system.

3. Press the K◄ or ►►I button to play the next or previous track on the mobile phone.

4. Press the ►II button to pause or resume music playback.

1. **Power ON/OFF Button:** Switches ON/OFF

2. **VOL +/VOL-:** Volume Up/Down

3. **Band button / Reply call**

4. **K◄ Button:** Tune down, seek down; Track down, fast reverse

5. **SEL (Selection) button**

6. **►►I Button:** Tune up, seek up; Track up, fast forward.

7. **Mute button, DEL (Delete) button**

8. **CLK (Clock setting) button / End call button**

9. **►II Button, preset station 1 button, keypad 1**

10. **INT (Intro) button, preset station 2 button, keypad 2**

11. **RPT (Repeat) button, preset station 3 button, keypad 3**

12. **RDM (Random), preset station 4 button, keypad 4**

13. **-10 (Previous 10 tracks), preset station 5 button, keypad 5**

14. **+10 (Next 10 tracks), preset station 6 button, keypad 6**

15. **ST (Stereo) button, keypad 7**

16. **LOUD (Loudness) button, keypad 8**

17. **AMS (Automatic Music Search) button, keypad 9**

18. **MODE button, keypad ***

19. **EQ (Equalizer) button, keypad 0**

20. **LOC (Local)/DX button, keypad #**

1. When the lithium cell battery becomes weak, it needs to be replaced.

2. Press and hold the movable block in the direction indicated by arrow 1. At the same time, pull the cell holder out of the remote control in the direction indicated by arrow 2.

3. Replace the old cell with a new one, ensuring the (+) polarity is facing upward.

4. Reinsert the cell holder into the remote control.

The remote comes with an insulating sheet that must be removed before first use.

• Position the emitting window of the remote control toward the sensor window of the unit.

• The operation angle for front panel remote control reception is about 30 degrees.

• The distance between the emitting window of the remote control and the sensor window of the unit should be less than 5 meters.

• Cell leakage may cause damage to the remote control.

• Do not dispose of cells in a fire as this may cause an explosion.

• Keep battery cells out of reach of children.

1. **Vehicle’s engine switch is not on.** Turn your Vehicle’s key to ACC or ON.

2. **Cable is not correctly connected.** Check the connection.

3. **Fuse is burnt.** Replace the fuse.

The volume may be in mute or set to a minimum. Check the volume level or mute ON/OFF, and adjust the volume to the desired level.

The installation angle is more than 30°. Adjust the installation angle to less than 30°.

The built-in micro-computer is not operating properly due to noise. Press the RESET button to restore the program to zero.

The station or signal is too weak. Select other stations with stronger signal levels.

Insert the antenna cable firmly into the antenna socket of this receiver.

The battery cable is not correctly connected. Connect the battery cable to the terminal that is always live.

The Push-to-Talk feature allows you to access SIRI or GOOGLE voice via Wireless BT.

• Your phone must support SIRI or GOOGLE voice. Once connected to BT, your phone will ask for access to your contact list.

• You are now ready to use PUSH-TO-TALK. Press the PUSH-TO-TALK icon. You are ready to talk. Say, “Call (CONTACT NAME)” The system will call without needing to use your phone.

NOTE: Samsung “S” Voice and other associated apps are not compatible.

Yes, the PYLE Smart App provides remote technology for your PLMRK47BK. You can download the PYLE Smart app from the Google or Apple Store and install it on your phone or tablet.