PREMIUM PCH762DR (01) PDF DOCUMENT

To ensure proper installation and performance of your PREMIUM PCH762DR cooker hood, please follow these requirements:

1. Do not install the cooker hood where there are many doors or windows, as this can affect the exhaust efficiency due to air convection.

2. Install the cooker hood directly above the hob. The recommended distance between the hob and the lower edge of the cooker hood is a minimum of 650mm and a maximum of 700mm.

3. For optimal performance, do not elongate the exhaust pipe too long. Try to minimize the number and severity of bends in the exhaust pipe and ensure the connection is airproof.

4. After hanging the unit on the wall, ensure the hood is level and vertical.

5. The air outlet must not be connected to chimney flues or combustion gas ducts. Under no circumstances should the air outlet be connected to ventilation ducts for a room in which fuel-burning appliances are installed.

SAFETY WARNING: The hood may have very sharp edges. Please wear protective gloves if it is necessary to remove any parts for installing, cleaning, or servicing.

Step 1:

Attach the exhaust pipe to the air outlet. Use one ST3.9 X10 screw to fix the exhaust pipe in place.

Step 2:

Match the bracket to the holes of the inner duct cover and fix it well with M4 screws. Then, match the bracket to the holes of the outer duct cover and fix it well with M4 screws.

Step 3:

Insert the inner duct cover into the outer duct cover.

Step 4:

Match the holes of the outer duct cover and the blower box. Fix the outer duct cover to the blower box using 8 M4 x 10 screws provided.

Step 5:

According to the size of the hook keyholes, drill 3 holes in a level line on the wall. The holes should be 8mm in diameter and 60-70mm in depth. Press the 3 provided expanding tubes into the holes. Fix the hook using the provided 5×60 wood screw. Then insert two M4x10 screws into holes A and B to fix the hook steadily on the wall.

Step 6:

Hang the entire PREMIUM PCH762DR hood unit onto the hook. Ensure the hood is level and vertical.

Step 7:

1. Raise the inner duct cover to the desired height and mark the two keyhole locations of the outer duct cover bracket on the wall with a pen.

2. Gently lower the inner duct cover. Drill the keyholes 60-70 mm deep on the marked horizontal line using an 8mm drill bit.

3. Press the provided expanding tubes into the holes.

4. Align the inner duct cover with the holes and tighten it using two 5×60 wood screws.

Step 8:

Extend the air outlet of the exhaust pipe out-of-door. Try to make the bend of the exhaust pipe more than 120°.

The control panel on your PREMIUM PCH762DR has several functions:

Timer/Clock Button:

• Timer: When the hood is working, touch this button once to set the timer. Each additional touch adds one minute, up to a maximum of 60 minutes.

• Clock: When the hood is not working, press and hold this button for 3 seconds. The display will show “88:88”. Use the Fan button to set the hour and the Light button to set the minute. When the hood is off, press and hold this button for 3 seconds to set the clock.

Fan Button:

• Touch once for high speed.

• Touch a second time for medium speed.

• Touch a third time for low speed.

• Touch a fourth time to stop the motor.

Light Button:

• Touch once to turn the light on.

• Touch again to turn the light off.

Motor On/Off Button:

• When the hood is working, touch this button once to prolong the working time by one minute.

• Touch twice to turn the hood off at once.

CAUTION: NEVER PUT YOUR HAND INTO THE AREA HOUSING WHILE THE FAN IS OPERATING.

For the optimal level of operation, clean the range hood surface, fan, and filter regularly.

1. Use only mild soap or detergent solutions to clean the cooker hood surface. Dry surfaces using a soft cloth.

2. Use a stainless steel cleaner to bring the glow back into a stainless steel finish.

3. Clean the aluminum filter once a week or according to use status. Press the buckle of the aluminum filter slightly, take off the filter, and put it into warm soapy water using mild detergent. Wipe the filter with a soft brush. Replace the filter after it is dry.

4. Clean the motor fan and other inside parts once every half year or according to use by a QUALIFIED PERSON.

5. DO NOT clean the motor with water or other liquid.

Caution: The LED lamp on your PREMIUM PCH762DR cannot be replaced with a new bulb; the entire LED lamp unit must be replaced. Make sure all control switches are off and the cooker hood is unplugged. The lamp unit may be hot, so wait until it is cool before proceeding.

Please follow the below instructions:

1. Take out the filters and cut off the wire connection of the lamp.

2. Press the spring according to the arrow direction, then you can take off the lamp unit.

3. You can replace it with a new LED lamp unit of no more than the original rating.

4. Put the new lamp unit into the hood in the reverse direction and connect the wire of the lamp.

5. Fit the filters back in place.

• Do not connect the air outlet to chimney flues or combustion gas ducts.

• Do not leave naked flames under this hood.

• In case of any damage to the power cable, have it replaced by a qualified person.

• Clean the hood correctly in accordance with the instructions to avoid the possibility of a fire accident.

• To replace the bulb, the task should be undertaken by a qualified electrician or a competent person. Always use a bulb with a rating no more than specified.

• Wear protective gloves before you start to clean the hood. Remove components gently during clearance.

• Never wash the control switch with water or any other liquid to avoid causing an electrical problem to the hood.

• The cleaning of the motor fan should be undertaken by a qualified person. Pay close attention to avoid any distortion of the fan during this process.

• Never pull the plug out of the power supply with a wet hand to avoid the possibility of electric shock.

• Disconnect the cooker hood from the power supply if this appliance will not be used for a long time.

CAUTION: Disconnect the power supply before servicing your PREMIUM PCH762DR.

STATUS	CAUSE AND METHOD OF REPAIRING	TOOL
The power supply is damaged	If the power supply is damaged, please call the technicians to repair.	“+” type Screwdriver, Sharp Pincers
The lamp works but the motor does not run	a) Remove the vane guard and rotate the vane by hand. If the vane cannot move smoothly, the core or bearings of the motor may be damaged. In this case, replace with a new motor. b) If the motor stops running and has a bad odor after a moment of operation, the motor wires may be burnt out. Replace the motor. c) If the starting wire (yellow) is disengaged from the condenser, it needs to be rewired. d) If the condenser is damaged, replace with a new one.	“+” type Screwdriver
The lamp works but the motor does not run	a) Take off the filter and check the connection between the air inlet and wind chamber is sealed or not. b) Check the connection between the air exhaust pipe and wind chamber for oil leaks. If “YES”, please fill it up with varnish or thinner.	“+” type Screwdriver
Machine vibration	a) If the motors were not firmly screwed, screw tighten them up. b) If the vane is damaged or unbalanced, replace with a new one.	“+” type Screwdriver
Weakness suction	a) The distance is too far between the Range Hood and the Gas Cooker. b) There are many windows (doors) causing the wind convection to be too strong. c) If the Range Hood is set upon a window, the best solution is to put a three-ply board on the back of the Range Hood to cover the hollow of the window.	“+” type Screwdriver
Installation of the model is tilted	a) Adjust the height of the model where it is hung on the ceiling. b) If the model tilts forward, lock it into the wall with a wood screw again (the screw should peep out around 0.5 ~ 1 cm from the wall), or check if the screws for fixing the model are loose or not.	“+” type Screwdriver
Bulb does not light	Just screw off the lamp shade and replace with a new bulb, then put the lamp shade back.	“+” type Screwdriver