PREMIUM PCH796DR (01) PDF DOCUMENT

The technical characteristics for the PREMIUM PCH796DR cooker hood are as follows:

Total Power: 154W

Three Speed Motor: 150W

LED Lights: 2 x 2W

Voltage: 110-120 V

Frequency: 60HZ

Filter: 6-layer filter

Control: 3-speed Push button

Before installing your PREMIUM PCH796DR cooker hood, please adhere to the following requirements:

1. Do not install the cooker hood where there are many doors or windows, as this can affect the exhaust efficiency of the hood caused by air convection.

2. Install the cooker hood directly above the hob. The recommended distance between the hob and the lower edge of the cooker hood is a minimum of 650mm and a maximum of 700mm.

3. To achieve optimum performance, do not elongate the exhaust pipe too long. Try to make the bend of the exhaust pipe less pronounced and as large as possible, ensuring the connection is airproof.

4. After hanging the unit on the wall, ensure the hood is level and vertical.

5. The air outlet must not be connected to chimney flues or combustion gas ducts. Under no circumstances should the air outlet be connected to ventilation ducts for a room in which fuel-burning appliances are installed.

SAFETY WARNING: The hood may have very sharp edges. Please wear protective gloves if it is necessary to remove any parts for installing, cleaning, or servicing.

Step 1: Put the exhaust pipe to the air outlet and use one ST3.9 X10 screw to fix it.

Step 2: Match the bracket to the holes of the inner duct cover and fix it well with M4 screws. Then, match the bracket to the holes of the outer duct cover and fix it well with M4 screws.

Step 3: Insert the inner duct cover into the outer duct cover.

Step 4: Match the holes of the outer duct cover and blower box. Fix the outer duct cover to the blower box using 8pcs M4 x 10 screws provided.

Step 5: According to the size of the hook key holes, drill 3 holes in level in the wall with an 8mm diameter and 60-70mm in depth. Press the 3 expanding tubes provided into the holes. Fix the hook using the 5×60 wood screw provided. Then insert two M4X10 screws into holes A and B to fix the hook on the wall steadily.

Step 6: Hang the entire hood unit onto the hook, ensuring the hood is level and vertical.

Step 7:

1. Draw the inner duct cover up to the suitable height and mark on the wall the two keyholes of the outer duct cover bracket with a pen.

2. Gently put down the inner duct cover. Drill the keyholes to a 60-70 mm depth on the horizontal level using an 8mm drill.

3. Press the expanding tubes provided into the holes.

4. Match the inner duct cover with the holes and tighten the inner duct cover with two 5×60 wood screws provided.

Step 8: Extend the air outlet of the exhaust pipe out-of-door. Try to make the bend of the exhaust pipe more than 120 degrees.

The control panel on your PREMIUM PCH796DR has the following functions:

A: Touch A, the fan runs at low speed. Press it again, the fan turns off.

B: Touch B, the fan runs at the mid speed. Press it again, the fan turns off.

C: Touch C, the fan runs at the high speed. Press it again, the fan turns off.

The A, B, and C buttons interact with each other.

D (Clock/Timer):

– When the hood is OFF, press and hold D for 3 seconds. Then touch C and E to adjust the hour and minute. Button G will function as a clock. In the screen, the left side is the hour, and the right is the minute.

– When the hood is operating, touch D to control the working time of the hood. Each touch adds 5 minutes, up to a maximum of 1 hour.

E (Light): Touch E to turn on the light. Press it again to turn off the light.

F (Delayed Off): When the hood is operating, touch F. The hood will not turn off at once; it will stay on for one minute and then turn off.

CAUTION: Never put your hand into the area housing while the fan is operating.

For the optimal level of operation, clean the range hood surface, fan, and filter regularly.

1. Use only mild soap or detergent solutions to clean the cooker hood surface. Dry surfaces using a soft cloth.

2. Use a stainless steel cleaner to bring the glow back into a stainless steel finish.

3. Clean the aluminum filter once a week or according to use status. Press the buckle of the aluminum filter slightly, take off the aluminum filter and put it into warm soapy water using mild detergent. Wipe the filter with a soft brush. Replace the filter after it is dry.

4. Clean the motor fan and other inside parts once every half year or according to use by a qualified person.

5. DO NOT clean the motor with water or other liquid.

Caution: The lamp unit may be hot! Wait until the unit is cool. Use the same type of lamp or light bulb. Make sure all control switches are off and the cooker hood is unplugged.

To replace a halogen lamp unit:

1. Take out the filters and cut off the wire connection of the lamp.

2. Press the spring according to the arrow direction, then you can take off the lamp unit.

3. You can replace it with a new halogen lamp unit of no more than the specified rating.

4. Put the new lamp unit into the hood in the reverse direction. Connect the wire of the lamp.

5. Fit on the filters.

To replace a new light bulb within the halogen unit:

A. Loosen the four screws of the lamp unit and take off the bottom cover.

B. Take out the light bulb assembly.

C. Take out the old light bulb, then replace it with a new light bulb.

D. Put the light bulb assembly in the lamp cup.

E. Put the bottom cover back on the lamp.

F. Fix the lamp with four screws.

To replace an LED lamp unit:

Caution: An LED lamp cannot be replaced with a new bulb; you must replace the entire LED lamp unit.

1. Take out the filters and cut off the wire connection of the lamp.

2. Press the spring according to the arrow direction to take off the lamp unit.

3. You can replace it with a new LED lamp unit of no more than the specified rating.

4. Put the new lamp unit into the hood in the reverse direction and connect the wire of the lamp.

5. Fit on the filters.

To replace a normal lamp bulb:

1. Take out the filters.

2. Loosen the old light bulb.

3. Replace it with a new light bulb of the same type and no more than the specified rating.

4. Fit on the filters.

Please follow these safety instructions when using your PREMIUM PCH796DR:

• Do not connect the air outlet to chimney flues or combustion gas ducts.

• Do not leave naked flames under this hood.

• In case of any damage to the power cable, have it replaced by a qualified person.

• Clean the hood correctly in accordance with instructions to avoid the possibility of a fire accident.

• Bulb replacement should be undertaken by a qualified electrician or a competent person. Always use a bulb with a rating that is not higher than specified.

• Wear protective gloves before you start to clean the hood. Remove components gently during cleaning.

• Never wash the control switch with water or other liquids to avoid electrical problems.

• The cleaning of the motor fan should be undertaken by a qualified person. Pay close attention to avoid any distortion of the fan during cleaning.

• Never pull the plug out of the power supply with a wet hand to avoid the possibility of electric shock.

• Disconnect the cooker hood from the power supply if this appliance will not be used for a long time.

CAUTION: Disconnect the power supply before servicing.

STATUS	CAUSE AND METHOD OF REPAIRING	TOOL
The power supply is damaged	If the power supply is damaged, please call the technicians to repair.	“+” type Screwdriver, Sharp Pincers
The lamp works but the motor does not run	a) Remove the vane guard and rotate the vane by hand. If the vane cannot move smoothly, the core or bearings of the motor may be damaged. In this case, replace with a new motor. b) If the motor stops running and has a bad odor after a moment of operation, the motor wires may be burnt out. Replace the motor. c) If the starting wire (yellow) is disengaged from the condenser, it needs to be rewired. d) If the condenser is damaged, replace with a new one.	“+” type Screwdriver
The lamp works but the motor does not run (Oil Leak)	a) Take off the filter and check if the connection between the air inlet and wind chamber is sealed. b) Check if the connection between the air exhaust pipe and wind chamber leaks oil. If “YES”, please fill it up with varnish or thinner.	“+” type Screwdriver
Machine vibration	a) If the motors were not firmly screwed, screw tighten them up. b) If the vane is damaged or unbalanced, replace with a new one.	“+” type Screwdriver
Weakness suction	a) The distance is too far between the Range Hood and the Gas Cooker. b) There are many windows (doors) causing strong wind convection. c) If the Range Hood is set upon a window, the best solution is to put a three-ply board on the back of the Range Hood to cover the hollow of the window.	“+” type Screwdriver
Installation of the model is tilted	a) Adjust the height of the model where it hangs on the ceiling. b) If the model tilts forward, lock it into the wall with a wood screw again (the screw should peep out around 0.5 ~ 1 cm from the wall), or check if the fixing screws are loose.	“+” type Screwdriver
Bulb does not light	Just screw off the lamp shade and replace with a new bulb, then put the lamp shade back.	“+” type Screwdriver

This product is marked with the WEEE (Waste of Electrical and Electronic Equipment) symbol. According to the WEEE directive, this product should be separately collected and treated. If at any time in the future you need to dispose of this product, please do NOT dispose of it with household waste. Please send this product to WEEE collecting points where available.