MABE GE CLME77014DFU (01) PDF Document

If you smell gas, follow these safety instructions for your MABE GE CLME77014DFU:

1. Do not try to light a match or cigarette, or turn on any gas or electrical appliance.

2. Do not touch any electrical switch; do not use any phone in your building.

3. Clear the room, building, or area of all occupants.

4. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions carefully.

5. If you cannot reach your gas supplier, call the fire department.

Under certain conditions, hydrogen gas can be produced in a water heater that has not been used for two weeks or more, which can be explosive. If the hot water has not been used for two weeks or more, prevent potential damage or injury by turning on all hot water faucets and allowing them to run for several minutes before using any electrical appliance connected to the hot water system. This allows any built-up hydrogen gas to escape. Do not smoke or use an open flame or appliance during this process.

Follow these steps to use the washer:

Step 1: Add detergent. For models with a fabric softener dispenser, you can add fabric softener (optional) and liquid bleach (optional) into their respective compartments.

Step 2: Add clothing to the wash basket.

Step 3: Select the load size and other wash options, then select the wash cycle.

Step 4: Close the lid and press the START button.

For bulky items, take one end and insert it in a spiral shape, arranging the item around the basket. If it exceeds the indicated limit, compress it slightly to ensure the volume is below the limit. For waterproof and water-resistant items (like diaper covers, bed covers, coats), use only the Bulky cycle. Do not use other cycles for these items, as water can get trapped, causing abnormal vibration and potential damage. Do not mix waterproof and non-waterproof items.

The Sanitized cycle on your MABE GE CLME77014DFU is designed to eliminate bacteria, viruses, and germs using high-temperature water. For correct operation, you must have hot water available in your installation.

1. Put the detergent in the bottom of the tub.

2. Add the clothes. This cycle is best for high-cotton items like towels, jeans, sheets, and bathrobes.

3. For best performance, set the “Temperature” and “Water Level” knobs to the “Automatic” position.

1. Selecting cycles: Turn the cycle knob to select from the available programs based on the type of clothes you are washing.

2. Temperatures: Select the water temperature for the wash and rinse cycles using the Temperature knob.

3. Water level: Select the water level based on your load size or use the automatic sensor option.

4. Selecting functions (Personal touch mode): Press the “Select” button repeatedly to choose independent functions like wash only, rinse only, or wash and spin. The indicator lights will show which functions are selected.

5. Start/pause: Press this button to start the washer or pause it during operation. Press it again to resume.

The MABE GE CLME77014DFU washer has several programs designed to clean and care for your clothes:

The fabric softener dispenser automatically releases liquid fabric softener at the proper time.

1. Make sure the dispenser is securely attached to the agitator.

2. Use only liquid diluted fabric softener. Pour the recommended amount into the dispenser. Never pour fabric softener directly on clothes.

3. Add water to the dispenser until it reaches the maximum fill line.

4. For proper dispersion, select the FABRIC SOFTENER setting on the control panel if available.

Note: Do not stop the washer or raise the lid during the first spin, as this will cause the dispenser to empty too soon.

1. Remove the dispenser from the top of the agitator.

2. Separate the dispenser cup from the cover by grasping the top and pushing down on the inside of the cup.

3. Soak both the cup and cover in a solution of 3.8 liters of warm water, 1/4 cup (60 ml) of heavy-duty liquid detergent, and 1 cup (240 ml) of bleach.

4. If necessary, loosen dirt with a soft cloth after soaking. Do not use a stiff brush.

5. Rinse and reassemble the dispenser, then place it back on the agitator.

The bleach funnel dilutes chlorine bleach as the washer fills.

1. Check clothing care labels for special instructions.

2. Measure liquid bleach carefully, following instructions on the bottle. Never pour undiluted liquid chlorine bleach directly onto clothes or into the wash basket. Do not pour powdered bleach into the funnel.

3. Before starting the washer, pour the measured amount of bleach directly into the bleach funnel.

Warning: Do not mix chlorine bleach with ammonia or acids like vinegar, as it can produce toxic gas.

Sorting: Sort laundry by color (whites, lights, colors), soil level, and fabric type (sturdy cottons, easy care, delicates). Also separate items that produce lint (like terry cloth) from items that collect lint (like corduroy).

Loading: Load the washer with dry items, no higher than the top row of holes in the basket. For wet items, set the water level to allow them to move freely. The water should just cover the clothes. Make sure bulky items are distributed along the basket wall. Agitation will not begin if the lid is up.

Wash Basket: Leave the lid open after washing to allow moisture to evaporate. To clean the basket, use a clean soft cloth dampened with liquid detergent, then rinse. Do not use harsh or gritty cleaners.

Fill Hoses: It is recommended to change the hoses every 5 years.

Exterior: Immediately wipe off any spills with a damp cloth. Avoid hitting the surface with sharp objects.

Long Vacations: Be sure the water supply is shut off at the faucets. Drain all water from the hoses if the weather will be below freezing.

1. Clean the lint filter before each use.

2. Load the dryer with clothes.

3. Select a drying cycle. For automatic cycles, the knob will not turn until the thermostat sensor indicates the clothes are dry. For timed cycles, the timer runs for the selected duration.

4. Close the dryer door and press START. Opening the door will stop the dryer. To restart, close the door and press START again.

Automatic cycles on your MABE GE CLME77014DFU determine fabric dryness for you. Select “less dry” for slightly damp clothes or “more dry” for completely dry clothes. Temperature settings include:

High: For regular to heavy cottons. For most loads, select OPTIMUM DRY.

Sanitized: For items like towels and jeans. Do not use for delicate clothing like lycra or sports synthetics.

Medium: For synthetics, blends, and items labeled permanent press.

Low: For delicates, synthetics, and special care knits. For items labeled tumble dry low.

Exterior: Wipe or dust any spills or washing compounds with a damp cloth.

The lint filter: Clean the filter before each use. Slide the grid out and move your fingers through the filter. To remove wax buildup from fabric softeners, wash the filter with soap and warm water. Dry it completely before replacing. Do not operate the dryer without the lint filter in place.

The exhaust duct: Inspect and clean the exhaust duct at least once a year to prevent clogging. Turn off electrical supply, disconnect the duct, vacuum it, and reconnect it.

The exhaust hood: Use a mirror to ensure the inner flaps move freely when operating and check for any nesting wildlife.

Proper venting is crucial for the performance of your MABE GE CLME77014DFU dryer.

Use only rigid or flexible metal 4″ diameter material approved by UL for the exhaust duct leading to the outside.

Do not use plastic or other combustible ductwork.

Use the shortest length possible.

Do not crush or collapse the duct.

Avoid resting the duct on sharp objects.

Venting must conform to local building codes.

This is likely caused by using too much detergent. Measure detergent carefully. Use less soap if you have soft water, a smaller load, or a lightly soiled load.

Check for the following possible causes:

Improperly connected hoses: Make sure the fill hoses and drain hose are tight at the faucets and correctly secured to the drain facility.

Clogged household drain: Your household plumbing may be clogged. You may need to call a plumber.

Constant pressure on hoses: Tighten hoses at the faucets and turn the water off after each use. It is recommended to replace fill hoses every 5 years.

Kinked or improperly connected drain hose: Straighten the drain hose and make sure the washer is not sitting on it. The top of the drain outlet should be less than 8 ft (2.5 m) above the floor.

Check these potential issues:

Water supply is off or improperly connected: Turn the hot and cold faucets on completely and ensure the hoses are connected to the correct faucets.

Clogged mesh filters: Turn off the water source and remove the connection hoses from the upper back of the washer. Use a brush to clean the washer valves, then reconnect the hoses and turn the water back on.

House water heater not set properly: Make sure your water heater is delivering water at 120°F-140°F (48°C-60°C).

Colder water temperatures: New detergents are formulated to work at lower water temperatures without affecting performance. This may be normal.

Check these common reasons:

Washer is unplugged: Make sure the cord is plugged securely into a working outlet.

Water supply is turned off: Turn both hot and cold faucets fully on.

Controls are not set properly: Check that you have selected a cycle.

Lid is open: The safety feature prevents agitation and spinning when the lid is open. Close the lid and restart the cycle.

Circuit breaker/fuse is tripped/blown: Check your house circuit breakers/fuses. Replace fuses or reset the breaker. The washer should have a separate outlet.

Electronics need to be reset: Unplug the washer, wait 2 minutes, plug it back in, and press START.

START was not pressed: Press the START button.

Lid magnet is missing: If the magnet on the lid is missing, the washer will not operate. This requires a service call.

This is likely due to an incorrect spin cycle selection. Make sure the spin cycle you’ve chosen matches the load you are washing. Some fabrics will naturally feel wetter when rinsed with cold water.

This could be due to a couple of reasons:

Incorrect use of fabric softener: Check the fabric softener package instructions and follow the directions for using the dispenser. Never pour softener directly on clothes.

Dye transfer: Separate whites or lightly colored items from dark-colored items to prevent dyes from bleeding.

This can be caused by several factors:

Insufficient detergent: Use more detergent, especially for larger loads. Follow the manufacturer’s directions.

Hard water: Use a water conditioner or install a water softener.

Water is not hot enough: Ensure your water heater is delivering water between 120°F – 140°F (48°C – 60°C).

Washer is overloaded: Select a load size that matches the laundry load to allow clothes to move freely.

Detergent is not dissolving: Add detergent as the basket is filling with water before adding clothes.

Dye transfer: Sort clothes by color. If a fabric label states to wash separately, it may have unstable dyes.

Consider the following causes and solutions:

Incorrect sorting: Separate lint-producing items (like chenille) from lint-collecting items (like corduroy).

Washing too long: Wash small loads for a shorter time than larger loads.

Detergent not dissolving: Add detergent while the basket is filling before adding clothes. Try a liquid detergent and use warmer water.

Overloading: Load clothes loosely, no higher than the top row of holes in the washer basket.

Incorrect use of fabric softener: Follow the instructions on the fabric softener package for using the dispenser.

Check for these issues:

Dryer is unplugged: Make sure the dryer plug is pushed completely into the outlet.

Fuse is blown/circuit breaker is tripped: Check the house fuse/circuit breaker box. Most electric dryers use 2 fuses/breakers. Replace the fuse(s) or reset the breaker(s).

Here are some possible reasons:

Fuse is blown/breaker is tripped: The dryer may run but not heat if only one fuse is blown or one breaker is tripped. Check the house fuse/circuit breaker box and replace both fuses or reset both breakers.

Gas service is off (for gas models): Make sure the main and dryer gas taps are completely open.

This may be caused by:

Improper use of fabric softener: Follow the directions on the fabric softener package.

Drying dirty items with clean ones: Only dry clean items. Dirty items can stain clean items and the dryer.

Stains appearing after drying: Some stains that are not visible when wet can appear after drying. Use proper washing procedures before drying.

Extended drying times can be caused by several factors:

Improper sorting: Separate heavy items from lightweight items.

Large loads of heavy fabrics: These contain more moisture. Separate large, heavy fabrics into smaller loads.

Lint filter is full: Clean the lint filter before each load.

Improper or obstructed ducting: Check installation instructions for proper venting. Make sure the ducting is clean, free of kinks, and unobstructed. Ensure the outside wall damper operates easily.

Overloading: Do not put more than one washer load in the dryer at a time.

Wrinkling can be caused by:

Overdrying: Select a shorter drying time. Remove items while they still have a slight amount of moisture by using a LESS DRY or DAMP DRY setting.

Letting items sit in the dryer: Remove, fold, or hang items immediately after the cycle finishes.

Overloading: Separate large loads into smaller ones.

To avoid shrinkage, follow the garment care labels exactly. Some fabrics shrink naturally when washed. If you are concerned about a particular item shrinking, do not wash or dry it in the machine. Some items may be pressed back into shape after drying.