MABE GE MCL2040PSDG (01) PDF Document

If you smell gas near your MABE GE MCL2040PSDG, follow these steps for your safety:

1. Do not try to light a match or cigarette, or turn on any gas or electrical appliance.

2. Do not touch any electrical switch; do not use any phone in your building.

3. Clear the room, building, or area of all occupants.

4. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions carefully.

5. If you cannot reach your gas supplier, call the fire department.

Under certain conditions, hydrogen gas may be produced in a water heater that has not been used for two weeks or more. Hydrogen gas can be explosive. To prevent injury or damage, if the hot water has not been used for two weeks or more, turn on all hot water faucets and allow them to run for several minutes before using any electrical appliance connected to the hot water system. This allows any built-up hydrogen gas to escape. Do not smoke or use an open flame or appliance during this process.

To ensure proper performance and safety of your MABE GE MCL2040PSDG, follow these installation requirements:

• Properly ground the appliance to conform with all codes and ordinances.

• Install or store it where it will not be exposed to temperatures below freezing or to the weather, which could cause permanent damage and invalidate the warranty.

• Connect to a properly rated, protected, and sized power supply circuit to avoid electrical overload.

• Remove all sharp packing items and dispose of all shipping materials properly.

Proper exhaust and ducting are critical for the MABE GE MCL2040PSDG dryer:

1. Gas dryers must be exhausted to the outside.

2. Use only rigid metal 4″ diameter ductwork inside the dryer cabinet. For exhausting to the outdoors, use only rigid metal or flexible metal 4″ diameter ductwork. Never use plastic or other combustible, easy-to-puncture ductwork.

To maintain a safe laundry area for your MABE GE MCL2040PSDG, follow these precautions:

• Keep the area underneath and around the appliance free of combustible materials such as lint, paper, rags, gasoline, chemicals, or other flammable vapors and liquids.

• Keep the floor around the appliance clean and dry to reduce the possibility of slipping.

• Keep all laundry aids (detergents, bleaches, etc.) out of the reach of children, preferably in a locked cabinet. Observe all warnings on container labels to avoid injury.

• Never climb on or stand on the MABE GE MCL2040PSDG.

• Do not allow children to climb on, hang from, stand on, or play on or in the appliance. Close supervision is necessary when the appliance is used near children.

• Do not store items that may burn or melt (such as clothing, paper, plastics) on top of the appliance or hang them from the door.

Before using your MABE GE MCL2040PSDG, please read and follow these important safety instructions:

• Do not mix chlorine bleach with ammonia or acids like vinegar or rust remover, as it can produce a toxic gas.

• Never attempt to operate the appliance if it is damaged, malfunctioning, or has missing/broken parts.

• Never reach into the appliance while it is moving.

• Before loading, unloading, or adding clothes, wait until the machine has completely stopped.

• Clean the lint filter before each load. Do not use the dryer if the lint screen is not in place.

• Do not wash or dry items spotted with combustible substances (wax, oil, paint, gasoline, kerosene, etc.).

• Do not place items exposed to cooking oils in your dryer, as this could cause a clothes load to catch fire.

• Do not dry articles containing rubber, plastic, or similar materials that may melt or burn.

• Do not store plastic, paper, or clothing that may burn or melt on top of the dryer during operation.

• Do not dry fiberglass articles in your dryer, as it could cause skin irritation from remaining particles.

You may use a dryer-applied fabric softener or an anti-static conditioner in your MABE GE MCL2040PSDG. We recommend using a fabric softener in the wash cycle according to the manufacturer’s instructions, or a dryer product for which the manufacturer provides written assurance on the package that it can be safely used in the dryer.

To avoid fire hazards, including spontaneous combustion, with your MABE GE MCL2040PSDG, adhere to the following:

• Do not dry articles containing foam rubber, latex, or similarly textured rubber-like materials.

• Do not dry articles containing flammable materials such as cleaning fluids, waxes, solvents, gasoline, kerosene, etc. Only dry water-washed fabrics.

• The clothes dryer produces combustible lint and must be connected to an outdoor exhaust. Regularly inspect the outdoor exhaust opening and remove any accumulation of lint.

When your MABE GE MCL2040PSDG is not in use, follow these steps:

• Grasp the plug firmly when disconnecting the appliance to avoid cord damage. Keep the cord away from traffic areas.

• Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage. It is recommended to change the fill hoses every 5 years.

• Before discarding the appliance, remove the washer and dryer lids to prevent children from hiding inside.

• Do not attempt to repair or replace any part of the appliance unless specifically recommended in the owner’s manual.

• Do not tamper with controls.

To operate your MABE GE MCL2040PSDG for a wash cycle, follow these steps:

Step 1: Add detergent, liquid bleach, and fabric softener (optional) to their respective dispensers.

Step 2: Add clothing to the washer basket.

Step 3: Select the load size, wash cycle, and other wash options using the control knobs and buttons.

Step 4: Close the lid and press the START button.

For best results with your MABE GE MCL2040PSDG, place the load of clothes evenly around the infuser (preferably not over it). The machine will start the cycle by turning the basket to accommodate the load.

For bulky items, take one end and insert it in a spiral shape, arranging it around the basket. If clothes exceed the indicated limit, compress them slightly to ensure the volume is below the limit.

For waterproof or water-resistant items, use ONLY the Bulky cycle. DO NOT use other cycles for items like diaper covers, waterproof bed covers, sleeping bags, or waterproof clothing, as water can get trapped and cause abnormal vibration or damage.

Washer Sanitized Cycle:

This cycle eliminates bacteria, viruses, and germs found in clothing. It uses high-temperature water, so you must ensure you have hot water available in your installation. Put detergent in the bottom of the tub, then add the clothes. This cycle is ideal for high-cotton items like towels, jeans, and sheets. For best performance, set the “Temperature” and “Water Level” knobs to the “Automatic” position.

Dryer Sanitized Cycle:

This is a high-temperature cycle. The duration depends on the humidity, quantity, and type of clothing. It is recommended for clothes with high cotton content. For best performance, fill the dryer up to half or 3/4 full and verify that the dryer duct is in good condition and free of obstructions.

To operate your MABE GE MCL2040PSDG washer, use the controls as follows:

1. Selecting cycles: Turn the main knob to select from the available programs based on the type of clothes you are washing.

2. Temperatures: Select the water temperature for the wash and rinse cycles using the temperature knob.

3. Load Size/Water Level: Select one of the 4 load levels or use the automatic sensor, which will determine the optimal water level for you.

4. Selecting functions: Press the select button repeatedly to choose independent functions like wash only, rinse only, or wash and spin. The lights will indicate the selected functions.

5. Start/pause: Press this button to start the washer or to pause it during operation. Press it again to resume.

The MABE GE MCL2040PSDG washer has several programs designed for different types of clothing and soil levels.

Selecting Temperature:

Turn the knob to select the desired temperature. For best results, you can use the ‘Automatic’ sensor position, where the MABE GE MCL2040PSDG selects the right temperature based on the program.

Load Size/Water Level:

This selection allows the system to calculate the amount of water needed. You can manually select a level (Minimum to Maximum) or use the ‘Automatic’ setting, which lets the sensor determine the ideal amount of water for each load, saving water and improving efficiency. The maximum fill level is automatically selected in the Bulky cycle.

The Personal Touch Mode on your MABE GE MCL2040PSDG allows you to run wash stages independently:

• eco: This function activates water conservation to decrease the amount of water used in the cycle.

• Wash only: This function will fill the washer and provide agitation. At the end of the wash stage, the spin light will turn on, but the washer will not drain the water.

• Rinse only: This function drains and spins the wash water, then fills the tub with clean water for a rinse agitation, and the rinse light will stay on without a final drain.

• Only wash and rise: Fills and agitates for a wash, then drains and fills again for a rinse, but does not perform a final drain.

• Only wash and spin: Fills and agitates for a wash, then drains the water and spins the clothes to complete the cycle.

• Only rise and spin: Drains the water, fills with clean water for a rinse, and then drains and spins the clothing.

Using the Dispenser:

1. Make sure the dispenser is securely attached to the agitator.

2. Use only liquid diluted fabric softener. Pour the recommended amount into the dispenser.

3. Add water to the dispenser until it reaches the maximum fill line.

4. Select the FABRIC SOFTENER setting on the control panel for proper dispersion. Never pour fabric softener directly on clothes.

Cleaning the Dispenser:

1. Remove the dispenser from the top of the agitator.

2. Separate the dispenser cup from the cover.

3. Soak both parts in a solution of 3.8 liters of warm water, 1/4 cup (60 ml) of heavy-duty liquid detergent, and 1 cup (240 ml) of bleach.

4. If necessary, use a soft cloth to loosen any dirt. Do not use a stiff brush.

5. Rinse, reassemble the dispenser, and place it back on the agitator.

The water fill dilutes the chlorine bleach as the MABE GE MCL2040PSDG fills for the wash cycle.

1. Check clothing care labels for special instructions.

2. Measure liquid bleach carefully, following the instructions on the bottle. Never pour undiluted liquid bleach directly onto clothes or into the wash basket. Do not pour powdered bleach into the bleach funnel.

3. Before starting the washer, pour the measured amount of bleach directly into the bleach funnel. If you prefer powdered bleach, add it to the wash basket with the detergent.

Do not mix chlorine bleach with ammonia or acids like vinegar, as it may produce a toxic gas.

Sorting wash loads: Sort laundry by color (whites, lights, colors), soil level, and fabric type (sturdy cottons, easy care, delicates). Also, separate items that produce lint (like terry cloth) from those that collect lint (like corduroy).

Proper use of detergent: Add detergent and turn on the washer before adding clothes so the detergent can work effectively. Using too little or too much detergent is a common cause of laundry problems. Use less detergent if you have soft water, a smaller load, or a lightly soiled load.

Loading the washer: Load the washer with dry items, no higher than the top row of holes in the basket. For wet items, ensure the water level is set correctly to allow free movement. The water level should just cover the clothes. To add items after the washer has started, lift the lid and submerge them in the water. Ensure bulky items are distributed along the basket wall.

• Wash basket: Leave the lid open after washing to allow moisture to evaporate. To clean the basket, use a clean soft cloth dampened with liquid detergent, then rinse. Do not use harsh or gritty cleaners.

• Fill hoses: It is recommended to change the hoses every 5 years.

• Exterior: Immediately wipe off any spills with a damp cloth. Try not to hit the surface with sharp objects.

• Long vacations: Be sure the water supply is shut off at the faucets. Drain all water from the hoses if the weather will be below freezing.

The MABE GE MCL2040PSDG dryer features both automatic and timed cycles.

Automatic Drying Cycles:

These cycles automatically determine fabric dryness. The knob will not turn until the thermostat sensor indicates the clothes are dry. You can select ‘less dry’ if you want clothes slightly damp at the end of the cycle, or ‘more dry’ if you want them to be drier. Cycle options include:

• High: For regular to heavy cottons.

• Medium: For synthetics, blends, and permanent press items.

• Low: For delicates, synthetics, and special care knits.

• Easy Care: For wrinkle-free garments and items needing special care.

• Cottons: For garments with cotton and fabrics combined with cotton.

• Delicates: For mostly synthetic clothes, small thin items, and underwear.

• Sanitized: A high-temperature cycle for items with high cotton content. Do not use for delicate clothing.

Timed Drying Cycles (Manual):

These cycles run for a selected amount of time.

• Dewrinkle: For removing wrinkles from clean items that are very lightly damp.

• Fluff: For freshening or removing lint from already dry clothing.

Exterior: Wipe or dust any spills or washing compounds with a damp cloth. Keep laundry pretreatment products away from the dryer, as they can damage the control panel and finishes.

The lint filter: Clean the filter before each use. Slide the grid out and move your fingers through the filter. If wax buildup occurs from fabric softeners, wash the filter with soap and warm water. Dry it completely before replacing. Do not operate the dryer without the lint filter in place. A qualified technician should vacuum the lint from the dryer once a year.

The exhaust duct: Inspect and clean the exhaust duct at least once a year to prevent clogging. A partially clogged exhaust can lengthen drying time.

1. Turn off the electrical supply by disconnecting the plug.

2. Disconnect the duct from the dryer.

3. Vacuum the duct with a hose attachment and reconnect it.

The exhaust hood: Use a mirror to ensure the inner flaps of the exhaust hood move freely when operating. Check for any wildlife (birds, insects, etc.) nesting inside.

For the best drying performance, the MABE GE MCL2040PSDG dryer needs to be properly vented:

• Use only rigid metal 4″ diameter material for the duct inside the dryer cabinet.

• Use only rigid or flexible metal 4″ diameter material approved by UL for the exhaust duct leading to the outside.

• Do not use plastic or other combustible ductwork.

• Use the shortest length possible.

• Do not crush or collapse the duct.

• Avoid resting the duct on sharp objects.

• Venting must conform to local building codes.

If you see too many suds in your MABE GE MCL2040PSDG washer, it is likely due to using too much detergent. Measure detergent carefully. Use less soap if you have soft water, a smaller load, or a lightly soiled load.

If your MABE GE MCL2040PSDG is leaking, check the following:

• Fill hoses or drain hose: Make sure hose connections are tight at the faucets and that washers are in place. Ensure the end of the drain hose is correctly inserted and secured to the drain facility.

• Household drain: Check household plumbing. You may need to call a plumber if it’s clogged.

• Constant pressure to hoses: Tighten hoses at the faucets and turn the water off after each use. Check the condition of fill hoses; they should be replaced every 5 years.

• Kinked or improperly connected drain hose: Straighten the drain hose and make sure the washer is not sitting on it. The top of the drain outlet should be less than 8 ft (2.5 m) above the floor.

If the water temperature in your MABE GE MCL2040PSDG seems incorrect, consider these points:

• Colder water temperatures: New detergents are formulated to work at lower water temperatures without affecting washer performance.

• Water supply: Turn hot and cold faucets completely on and make sure hoses are connected to the correct faucets.

• Clogged mesh filters: Turn off the water source and remove the connection hoses from the upper back of the washer. Use a brush to clean the washer valves, then reconnect the hoses and turn the water back on.

• House water heater settings: Make sure the house water heater is delivering water at 120°F-140°F (48°C-60°C).

If the water pumped out before the cycle was complete on your MABE GE MCL2040PSDG, it could be because the lid was lifted or the cycle was put on pause for over 24 hours. To fix this, simply reset the cycle.

This is normal for the MABE GE MCL2040PSDG. The washer can be paused during the spin cycle to remove water containing soap more efficiently.

This is normal. The pump in the MABE GE MCL2040PSDG is leaving a small amount of water at the inlet, which is then diluted with soap and clean water during the next cycle.

If your MABE GE MCL2040PSDG washer won’t start, check the following potential causes:

• Washer is unplugged: Make sure the cord is plugged securely into a working outlet.

• Water supply is turned off: Turn both hot and cold faucets fully on.

• Controls are not set properly: Check the controls to ensure a cycle is selected.

• Lid is open: The safety feature prevents agitation and spinning when the lid is open. Close the lid and restart the cycle.

• Circuit breaker/fuse is tripped/blown: Check your house circuit breakers/fuses. Replace fuses or reset the breaker. The washer should have a separate outlet.

• Electronics need to be reset: Unplug the washer, wait 2 minutes, plug it back in, and press START.

• START was not pressed: Press the START button.

• Lid magnet is missing: This will require a service call.

This is part of the normal operation of the MABE GE MCL2040PSDG. When the machine is turned off manually (only in spin), the shifting mechanism is disengaging to return to its initial position, and the shifter will disengage the motor before it completely shuts down. If the lid is raised before the motor is disengaged, it will resume when the lid is closed (only in fill and wash).

If clothes are too wet, the incorrect spin cycle may have been selected. Make sure the spin cycle selected matches the load you are washing. Some fabrics will feel wetter when rinsed with cold water.

Colored spots can be caused by improper use of fabric softener or by dye transfer. Check the fabric softener package for instructions and follow the directions for using the dispenser. To prevent dye transfer, separate whites or lightly colored items from dark colors.

If clothes appear grayed or yellowed, check these possible causes:

• Insufficient amount of detergent: Use more detergent, especially with larger loads. Follow the detergent manufacturer’s directions.

• Hard water: Use a water conditioner or install a water softener.

• Water is not hot enough: Make sure your water heater is delivering water at 120°F – 140°F (48°C – 60°C).

• Washer is overloaded: Select a load size based on the laundry load.

• Detergent is not dissolving: Add detergent as the basket is filling with water, before loading clothes.

• Dye transfer: Sort clothes by color. If a fabric label states to wash separately, unstable dyes may be indicated.

To reduce lint and residue on clothes, try the following:

• If you line dry your clothes, they may retain more lint than if you use a clothes dryer.

• Sort laundry correctly, separating lint producers (like chenille) from lint collectors (like corduroy).

• Avoid washing too long; wash small loads for a shorter time than larger loads.

• Ensure detergent is dissolving by adding it as the basket fills with water before adding clothes. You can also try a liquid detergent or use warmer water.

• Do not overload the washer. Load clothes loosely, no higher than the top row of holes in the basket.

• Use fabric softener correctly according to package instructions.

• Pilling: This is a result of normal wear on poly-cotton blends and fuzzy fabrics. While not caused by the washer, you can slow the pilling process by washing garments inside out.

• Snags, holes, tears: This can be caused by pins, brooches, hooks, sharp buttons, zippers, or sharp objects left in pockets. Fasten all closures and remove loose items from pockets. Also, turn knits inside out. Undiluted chlorine bleach can also damage fabrics; check the bleach package for proper use. Chemicals like hair bleach or dye can also cause damage; rinse these items before washing.

To reduce wrinkling, try these tips:

• Sort properly: Avoid mixing heavy items (like work clothes) with light items (like blouses).

• Try a fabric softener.

• Avoid overloading: Load the washer so clothes have enough room to move freely and the water covers all garments.

• Use correct cycles: Match the cycle selection to the type of fabric you are washing.

• Avoid overly hot water: Repeated washing in water that is too hot can cause wrinkles.

If the dryer doesn’t start:

• Check if the dryer is unplugged. Make sure the dryer plug is pushed completely into the outlet.

• Check if a fuse is blown or a circuit breaker is tripped. Check the house fuse/circuit breaker box and replace the fuse or reset the breaker. Note that most electric dryers use 2 fuses/breakers.

If the dryer doesn’t heat:

• Check if a fuse is blown or a breaker is tripped. The dryer may dry but not heat if only one fuse is blown or one breaker is tripped. Check the house fuse/circuit breaker box and replace both fuses or reset both breakers.

• For gas models, check if the gas service is off. Make sure the main and dryer taps are completely open.

Some shaking or noise is normal for the MABE GE MCL2040PSDG. However, if it’s excessive, the dryer may be on an uneven ground. Move the Laundry Center to an even floor space, or adjust the leveling legs as necessary until it is level.

• Greasy spots: This may be due to improper use of fabric softener, or from drying dirty items with clean ones. Follow directions on the fabric softener package and use your dryer to dry only clean items.

• Lint on clothes: This can be caused by a full lint filter, improper sorting, static electricity, overloading, or items like paper left in pockets. Clean the lint screen before each load, sort lint producers from lint collectors, and empty all pockets.

• Static occurs: This can happen if no fabric softener was used, from overdrying, or from synthetic/permanent press fabrics. Try using a fabric softener and set the dryer to LESS DRY or DAMP DRY.

Inconsistent drying times: Automatic drying times will vary according to the type of heat used, load size, fabric type, wetness of clothes, and the condition of the exhaust ducts.

Clothes take too long to dry:

• Improper sorting: Separate heavy items from lightweight items.

• Large loads of heavy fabrics: These contain more moisture. Separate them into smaller loads.

• Improperly set controls: Match control settings to the load you are drying.

• Lint filter is full: Clean the lint filter before each load.

• Improper or obstructed ducting: Check installation instructions for proper ducting/venting. Make sure the ducting is clean, free of kinks, and unobstructed, and that the outside wall damper operates easily.

• Blown fuse or tripped circuit breaker: Since most dryers use 2 fuses/breakers, make sure both are operating.

To prevent wrinkling:

• Avoid overdrying by selecting a shorter drying time. Remove items while they still hold a slight amount of moisture by selecting LESS DRY or DAMP DRY.

• Do not let items sit in the dryer after the cycle finishes. Fold or hang them immediately.

• Avoid overloading by separating large loads into smaller ones.

To prevent shrinking:

• Some fabrics shrink naturally when washed. To avoid shrinkage, follow garment care labels exactly.

• Some items may be pressed back into shape after drying.

• If you are concerned about shrinkage in a particular item, do not wash or dry it.