JVC GR-D31 (01) PDF DOCUMENT

To ensure safe use of your JVC GR-D31 digital video camera, please observe the following precautions:

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

CAUTIONS:

• This camcorder is designed for NTSC-type color television signals. Live recording and LCD/viewfinder playback are possible anywhere, but playback on a television requires a compatible standard.

• Only use JVC BN-V408U/V416U/V428U battery packs and the provided multi-voltage AC Adapter for power.

• Ensure sufficient ventilation (10 cm or more on all sides) when installed in a cabinet or on a shelf. Do not block ventilation holes.

• Do not place naked flame sources, like lighted candles, on the apparatus.

• Dispose of batteries according to local rules and laws.

• The apparatus should not be exposed to dripping or splashing. Do not use it in a bathroom or places with water.

• Do not place containers filled with water or liquids on top of the unit.

• Do not point the lens or viewfinder directly into the sun to avoid eye injury and internal damage.

• Always use the provided shoulder strap for carrying. Do not carry the camcorder by the viewfinder or LCD monitor.

• Be careful not to get your finger caught in the cassette holder cover.

• Do not use a tripod on unsteady or unlevel surfaces.

• Avoid leaving the camcorder on top of a TV with cables connected, as tripping on the cables can cause it to fall.

The JVC GR-D31 comes with the following accessories:

• AC Adapter AP-V11U or AP-V13U

• Battery Pack BN-V408U

• Lens Cap

• Audio/Video Cable (ø3.5 mini-plug to RCA plug)

• Shoulder Strap

• Core Filter (for optional S-Video cable)

NOTE: To maintain optimum performance, provided cables may have one or more core filters. If a cable has only one, the end closest to the filter should be connected to the camcorder.

To protect the lens of your JVC GR-D31, attach the provided lens cap as follows:

1. Make sure the arrow on the lens cap string loop is pointing upward.

2. Loop the string around the grip strap anchor point.

3. Push the cap onto the lens. To confirm it is on correctly, make sure the cap is flush with the camera body.

The Core Filter helps reduce interference. To attach it to an optional cable for your JVC GR-D31:

1. Release the stoppers on both ends of the Core Filter to open it.

2. Run the cable through the Core Filter, leaving approximately 3 cm of cable between the plug and the filter. Wind the cable once around the outside of the Core Filter, ensuring it is not slack.

3. Close the Core Filter until it clicks shut.

NOTE: When connecting the cable, attach the end with the Core Filter to the camcorder.

The JVC GR-D31 has an Automatic Demonstration feature that starts when “DEMO MODE” is “ON” (factory-preset) and there has been no operation for about 3 minutes with no cassette loaded. Performing any operation stops it temporarily, but it will resume after 3 more minutes of inactivity.

To cancel the Automatic Demonstration:

1. Set the Power Switch to “M” while pressing the Lock Button, then press the MENU/VOLUME wheel in.

2. Rotate the MENU/VOLUME wheel to select “SYSTEM” and press it.

3. Rotate the wheel to select “DEMO MODE” and press it.

4. Rotate the wheel to select “OFF” and press it.

5. Rotate the wheel to select “RETURN” and press it twice to exit the menu.

Charging the Battery Pack:

1. With the arrow on the battery pack pointing up, push it slightly against the battery pack mount and slide it up until it locks in place.

2. Set the Power Switch to “OFF (CHARGE)”.

3. Connect the AC Adapter to the camcorder’s DC input and plug the adapter into an AC outlet. The POWER/CHARGE lamp will blink to indicate charging.

4. When the POWER/CHARGE lamp goes off, charging is finished. Unplug the AC Adapter.

To detach the battery, slide it down while sliding down the BATT. RELEASE switch.

Using AC Power:

Connect the AC Adapter to the camcorder and an AC outlet as described in the charging steps. The camcorder can be operated using AC power. Before detaching the power source, make sure the camcorder’s power is turned off.

Approximate Charging Times:

Approximate Recording Times:

Grip Adjustment:

1. Separate the Velcro strip on the grip.

2. Pass your right hand through the loop and grasp the camcorder.

3. Adjust the strap so your thumb and fingers can easily operate the Recording Start/Stop button, Power Switch, and Power Zoom Lever. Fasten the Velcro strip to your preference.

Viewfinder Adjustment:

1. Set the Power Switch to “A” or “M”.

2. Pull out the viewfinder fully and adjust it manually for the best viewability.

3. Turn the Diopter Adjustment Control until the indications in the viewfinder are clearly focused.

Shoulder Strap Attachment:

Thread one end of the strap through an eyelet on the camcorder, then fold it back and thread it through the buckle. Repeat for the other eyelet. Confirm the strap is not twisted.

Tripod Mounting:

CAUTION: When attaching the camcorder to a tripod, extend its legs to stabilize it. It is not advised to use small sized tripods, as this may cause damage to the unit by falling over.

To attach the JVC GR-D31 to a tripod, align the tripod’s direction stud and screw with the stud hole and mounting socket on the bottom of the camcorder. Then tighten the screw clockwise.

The JVC GR-D31 must be powered on to load or eject a cassette.

1. Slide and hold the OPEN/EJECT switch in the direction of the arrow, then pull the cassette holder cover open until it locks. The cassette holder will open automatically.

2. Insert or remove a tape. To close the holder, press the area marked “PUSH HERE”. The holder will recede automatically.

3. Close the cassette holder cover firmly until it locks into place.

To Protect Recordings: To prevent a tape from being recorded over, slide the erase protection tab on the back of the tape to “SAVE”. To record on the tape again, slide it back to “REC”.

Approximate Recording Time:

Date/Time Settings:

1. Set the Power Switch to “M” and ensure the LCD monitor or viewfinder is on.

2. Press the MENU/VOLUME wheel in.

3. Rotate the wheel to select “(CAMERA DISPLAY)” and press it.

4. Rotate the wheel to select “CLOCK ADJ.” and press it. “Month” will be highlighted.

5. Rotate the wheel to input the month, then press it. Repeat this process to input the day, year, hour, and minute.

6. Rotate the wheel to select “RETURN” and press it twice to close the menu.

Recording Mode Setting (SP/LP):

1. Set the Power Switch to “M” and ensure the LCD monitor or viewfinder is on.

2. Press the MENU/VOLUME wheel in.

3. Rotate the wheel to select “A (CAMERA)” and press it.

4. Rotate the wheel to select “REC MODE” and press it. The Sub Menu appears.

5. Select “SP” or “LP” by rotating the wheel and pressing it.

6. Rotate the wheel to select “RETURN” and press it twice to close the menu.

Note: “LP” (Long Play) mode is more economical, providing 1.5 times the recording time of “SP” (Standard Play) mode. Tapes recorded in LP mode are best played back on the same camcorder.

Before starting, ensure power is supplied, grip and viewfinder are adjusted, a cassette is loaded, and the recording mode is set.

1. Remove the lens cap.

2. Set the Power Switch to “A” (Full Auto) or “M” (Manual) while pressing the Lock Button.

3. To shoot using the LCD monitor, open it fully. To shoot using the viewfinder, pull it out. The camcorder enters Record-Standby mode and “PAUSE” is displayed.

4. Press the Recording Start/Stop button. “REC” appears, the tally lamp lights, and recording begins.

5. To stop recording, press the Recording Start/Stop button again. The camcorder re-enters Record-Standby mode.

Note: If the Record-Standby mode continues for 5 minutes, the camcorder’s power shuts off automatically to save power.

To use the zoom feature on your JVC GR-D31:

• Zoom In (Telephoto): Slide the Power Zoom Lever towards “T”.

• Zoom Out (Wide): Slide the Power Zoom Lever towards “W”.

The further you slide the lever, the faster the zoom action. Zooming is possible up to 700X (combining 16X optical and digital zoom). You can limit the zoom to 16X or 40X in the menu settings. Macro shooting (as close as 5cm) is possible when zoomed all the way out to “W”.

1. Load a recorded tape.

2. Set the Power Switch to “PLAY” while pressing the Lock Button.