JEEP WRANGLER 2022 (02) PDF DOCUMENT

Utility vehicles like the JEEP WRANGLER 2022 have a significantly higher rollover rate than other types of vehicles. This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles. It is capable of performing better in a wide variety of off-road applications. Driven in an unsafe manner, all vehicles can go out of control. Because of the higher center of gravity, if this JEEP WRANGLER 2022 is out of control it may roll over while some other vehicles may not. Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this JEEP WRANGLER 2022 safely may result in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully.

Any modifications or alterations to this JEEP WRANGLER 2022 could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.

The symbols in the JEEP WRANGLER 2022 Owner’s Manual indicate different types of information:

• WARNING!: These statements are against operating procedures that could result in a collision, bodily injury and/or death.

• CAUTION!: These statements are against procedures that could result in damage to your vehicle.

• NOTE:: A suggestion which will improve installation, operation, and reliability. If not followed, may result in damage.

• TIP:: General ideas/solutions/suggestions on easier use of the product or functionality.

• PAGE REFERENCE ARROW: Follow this reference for additional information on a particular feature.

• FOOTNOTE: Supplementary and relevant information pertaining to the topic.

The JEEP WRANGLER 2022 is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter ‘n Go™ (if equipped), and Remote Start (if equipped). The key fob allows you to lock or unlock the doors and swing gate from distances up to approximately 66 ft (20 m). The key fob does not need to be pointed at the vehicle to activate the system. The key fob also contains a mechanical key.

The key fob’s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device. This may result in poor performance. With the ignition on and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.

Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.

The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks. In order to ensure complete efficiency of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.

To unlock the doors and swing gate:

• Push and release the unlock button on the key fob once to unlock the driver’s door.

• Push and release the unlock button on the key fob twice to unlock all the doors and swing gate.

To lock all the doors, push the lock button once.

When the doors are unlocked, the turn signals will flash and the illuminated entry system will be activated. When the doors are locked, the turn signals will flash and the horn will chirp.

All doors can be programmed to unlock on the first push of the unlock button through the Uconnect Settings.

In case the ignition switch of the JEEP WRANGLER 2022 does not change with the push of a button, the key fob may have a low or fully depleted battery. A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob. If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.

The recommended replacement battery for the JEEP WRANGLER 2022 key fob is CR2450.

1. Remove the back cover of the fob by inserting a flat-blade screwdriver into the slot on the bottom of the fob. Pry until the cover unsnaps, being careful not to damage the seal. Proceed counterclockwise to pry the remaining snaps until the battery cover can be removed.

2. Remove the depleted battery by inserting a small flat-blade screwdriver into the battery removal slot and sliding the battery forward and up, being careful not to damage the electronic board underneath.

3. Install the new battery into the key fob, making sure the positive (+) side is facing up. Slide the battery until it is seated securely below the tabs.

4. Reassemble the back cover, making sure it is properly aligned before snapping it back in place.

Do not touch the battery terminals that are on the back housing or the printed circuit board. When a key fob battery is low, a warning will be indicated on the JEEP WRANGLER 2022 instrument cluster, and the fob LED will no longer illuminate with a button press.

• The integrated key fob contains a coin cell battery. Do not ingest the battery; there is a chemical burn hazard. If the coin cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.

• If you think a battery may have been swallowed or placed inside any part of the body, seek immediate medical attention.

• Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.

Programming the key fob for the JEEP WRANGLER 2022 may be performed by an authorized dealer.

• Once a key fob is programmed to a vehicle, it cannot be repurposed and reprogrammed to another vehicle.

• Only key fobs that are programmed to the JEEP WRANGLER 2022 electronics can be used to start and operate the vehicle. Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.

Duplication of key fobs may be performed at an authorized dealer. This procedure consists of programming a blank key fob to the vehicle electronics. A blank key fob is one that has never been programmed.

• Always remove the key fobs from the JEEP WRANGLER 2022 and lock all doors when leaving the vehicle unattended.

• Always remember to place the Keyless Enter ‘n Go™ Ignition in the OFF position.

The Sentry Key Immobilizer system prevents unauthorized JEEP WRANGLER 2022 operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked.

The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation. Therefore, only key fobs that are programmed to the JEEP WRANGLER 2022 can be used to start and operate the vehicle. The system cannot reprogram a key fob obtained from another vehicle.

After placing the ignition in the ON/RUN position, the Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the light begins to flash after the bulb check, it indicates that someone attempted to start the engine with an invalid key fob. In the event that a valid key fob is used to start the engine but there is an issue with the vehicle electronics, the engine will start and shut off after two seconds.

If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electronics. Should this occur, have the JEEP WRANGLER 2022 serviced as soon as possible by an authorized dealer.

The Sentry Key Immobilizer system on the JEEP WRANGLER 2022 is not compatible with some aftermarket Remote Start systems. Use of these systems may result in vehicle starting problems and loss of security protection.

The push button ignition in the JEEP WRANGLER 2022 can be placed in the following modes:

• OFF:

  • The engine is stopped.

  • Some electrical devices (e.g. power locks, alarm, etc.) are available.

• ACC:

  • Engine is not started.

  • Some electrical devices are available.

• RUN:

  • Driving position.

  • All electrical devices are available.

• START:

  • The engine will start.

In case the ignition switch does not change with the push of the START/STOP ignition button because the key fob battery is low or depleted, a backup method can be used to operate the ignition switch. Put the nose side of the key fob (side with the mechanical flip key) against the START/STOP ignition button and push to operate the ignition switch.

• Do not press the mechanical key against the START/STOP ignition button.

• Do not use sharp metal objects (e.g. screwdriver etc.) to pry the button out of the ignition switch. This button comes as an assembly, and is not removable. This can damage the silicone shield.

• When exiting the JEEP WRANGLER 2022, always remove the key fob from the vehicle and lock your vehicle.

• Never leave children alone in the JEEP WRANGLER 2022, or with access to an unlocked vehicle.

The Remote Start system uses the key fob to start the JEEP WRANGLER 2022 engine conveniently from outside the vehicle while still maintaining security. The system has a range of 328 ft (100 m). Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.

To use Remote Start:

Push and release the Remote Start button on the key fob twice within five seconds. The JEEP WRANGLER 2022 doors and swing gate will lock, the turn signals will flash twice, and the horn will chirp twice. Pushing the Remote Start button again will shut the engine off.

• With Remote Start, the engine will only run for 15 minutes.

• Remote Start can only be used twice.

• If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.

• The parking lights will turn on and remain on during Remote Start mode.

• For security, power window operation is disabled when the vehicle is in the Remote Start mode.

• The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.

All of the following conditions must be met before the JEEP WRANGLER 2022 engine will remote start:

• Gear selector in PARK

• Doors closed

• Hood closed

• Swing gate closed

• Hazard switch off

• Brake switch inactive (brake pedal not pressed)

• Battery at an acceptable charge level

• Panic button not pushed

• System not disabled from previous Remote Start event

• Vehicle Security system indicator flashing

• Ignition in OFF position

• Fuel level meets minimum requirement

• All removable doors must not be removed

• Malfunction Indicator Light (MIL) not illuminated

• Do not start or run an engine in a closed garage or confined area. Exhaust gas contains carbon monoxide (CO) which is odorless and colorless. Carbon monoxide is poisonous and can cause serious injury or death when inhaled.

• Keep key fobs away from children. Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.

To drive the JEEP WRANGLER 2022 after starting the Remote Start system, either push and release the unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter ‘n Go™ Passive Entry via the door handles, and disarm the Vehicle Security system (if equipped). Then, prior to the end of the 15-minute cycle, push and release the START/STOP ignition button.

The Remote Start system will turn the engine off if the Remote Start button on the key fob is pushed again, or if the engine is allowed to run for the entire 15-minute cycle. Once the ignition is placed in the ON/RUN position, the climate controls will resume previously set operations (temperature, blower control, etc.).

When Remote Start is active in the JEEP WRANGLER 2022, and the outside ambient temperature is 40°F (4.5°C) or below, the system will automatically activate front defrost for 15 minutes or less. The time is dependent on the ambient temperature. Once the timer expires, the system will automatically adjust the settings depending on ambient conditions.

When Remote Start is activated in the JEEP WRANGLER 2022, the front and rear defrost will automatically turn on in cold weather. The heated steering wheel and driver heated seat feature will turn on if programmed in the Comfort menu screen within Uconnect Settings. In warm weather, the driver vented seat feature will automatically turn on when the Remote Start is activated, if programmed in the Comfort menu screen. The vehicle will adjust the climate control settings depending on the outside ambient temperature.

These features will stay on through the duration of Remote Start, or until the ignition is placed in the ON/RUN position. The climate control settings will change, and exit the automatic defaults, if manually adjusted by the driver while the vehicle is in Remote Start mode. This includes turning the climate controls off using the OFF button.

When Remote Start is active in the JEEP WRANGLER 2022 and the outside ambient temperature is less than 33°F (0.6°C), the Windshield Wiper De-Icer will activate. Exiting Remote Start will resume its previous operation. If the Windshield Wiper De-Icer was active, the timer and operation will continue.

One of the following messages will display in the JEEP WRANGLER 2022 instrument cluster if the vehicle fails to remote start or exits Remote Start prematurely:

• Remote Start Cancelled — Door Open

• Remote Start Cancelled — Hood Open

• Remote Start Cancelled — Fuel Low

• Remote Start Cancelled — Swing Gate Open

• Remote Start Cancelled — Time Expired

• Remote Start Disabled — Start Vehicle To Reset

The message will stay active until the ignition is placed in the ON/RUN position.

The Vehicle Security system of the JEEP WRANGLER 2022 monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation. When the alarm is activated, the interior switches for door locks are disabled. The Vehicle Security system provides both audible and visible signals. If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the park lamps and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.

Follow these steps to arm the Vehicle Security system in your JEEP WRANGLER 2022:

1. Make sure the vehicle’s ignition is placed in the OFF position.

2. Perform one of the following methods to lock the vehicle:

   • Push lock on the interior power door lock switch with the driver and/or passenger door open.

   • Push the lock button on the exterior Passive Entry door handle with a valid key fob available in the same exterior zone.

   • Push the lock button on the key fob.

3. If any doors are open, close them.

The Vehicle Security system will not arm if you lock the doors using the manual door lock.

The Vehicle Security system of the JEEP WRANGLER 2022 can be disarmed using any of the following methods:

• Push the unlock button on the key fob.

• Grab the Passive Entry door handle (if equipped).

• Cycle the vehicle ignition system out of the OFF position.

The driver’s door key cylinder cannot arm or disarm the Vehicle Security system. When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.

If the Vehicle Security system in the JEEP WRANGLER 2022 is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound. If this occurs, disarm the Vehicle Security system.

If something triggers the alarm in the JEEP WRANGLER 2022 and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29-second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.

Careless handling and storage of the removable door panels of the JEEP WRANGLER 2022 may damage the seals, causing water to leak into the vehicle’s interior.

All doors of the JEEP WRANGLER 2022 are equipped with an interior rocker-type door lock lever. To lock a door when leaving your vehicle, push the rocker lever forward to the lock position and close the door. To unlock the door, push the rocker lever rearward.

The mechanical flip key can be used to lock or unlock the doors, swing gate (if equipped with a lock), glove compartment, and console storage.

• For personal security reasons and safety in a collision, lock the JEEP WRANGLER 2022 vehicle doors when you drive, as well as when you park and exit the vehicle.

• When exiting the JEEP WRANGLER 2022, always switch off the ignition and remove the key fob from the vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death.

• Never leave children alone in the JEEP WRANGLER 2022, or with access to an unlocked vehicle.

• Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector.

• Do not leave the key fob in or near the JEEP WRANGLER 2022, or in a location accessible to children. A child could operate power windows, other controls, or move the vehicle.

The power door lock switch in the JEEP WRANGLER 2022 is located on each front door panel. Push the switch forward to unlock the doors, and rearward to lock the doors.

The Passive Entry system is a feature that allows you to lock and unlock the JEEP WRANGLER 2022 door(s) and swing gate without having to push the key fob lock or unlock buttons.

Passive Entry may be programmed on/off within the Uconnect Settings. The key fob may not be detected by the JEEP WRANGLER 2022 Passive Entry system if it is located next to a mobile phone, laptop, or other electronic device; these devices may interfere with the key fob’s wireless signal and prevent the Passive Entry system from locking/unlocking the vehicle.

With a valid Passive Entry key fob within 5 ft (1.5 m) of the door handle, grab the handle to unlock the JEEP WRANGLER 2022. Grabbing the driver’s door handle will unlock the driver door automatically. Grabbing the passenger door handle will unlock all doors and the swing gate automatically.

Either the driver door only or all doors will unlock when you grab hold of the front driver’s door handle, depending on the selected setting in the Uconnect system.

Passive Entry Unlock initiates illuminated approach (low beams, license plate lamp, position lamps) for whichever time duration is set between 0, 30, 60 or 90 seconds. Passive Entry Unlock also initiates two flashes of the turn signal lamps.

If wearing gloves, or if it has been raining/snowing on the Passive Entry door handle, the unlock sensitivity can be affected, resulting in a slower response time.

If the JEEP WRANGLER 2022 is unlocked by Passive Entry and no door is opened within 60 seconds, the vehicle will relock and, if equipped, will arm the Vehicle Security system.

To minimize the possibility of unintentionally locking a Passive Entry key fob inside the JEEP WRANGLER 2022, the Passive Entry system is equipped with an automatic door unlock feature which will function only if the ignition switch is in the OFF position.

FOBIK-Safe only executes in vehicles with a START/STOP ignition. There are three situations that trigger a FOBIK-Safe search in any Passive Entry vehicle:

• A lock request is made by a valid Passive Entry key fob while a door is open.

• A lock request is made by the Passive Entry door handle while a door is open.

• A lock request is made by the door panel switch while the door is open.

When any of these situations occur, after all open doors are shut, the FOBIK-Safe search will be executed. If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer. If Passive Entry is disabled using Uconnect system, the key fob protection described in this section remains active/functional.

The JEEP WRANGLER 2022 will only unlock the doors during a FOBIK-Safe operation when a valid Passive Entry key fob is detected inside the vehicle. The vehicle will not unlock the doors when any of the following conditions are true:

• A second valid Passive Entry key fob is detected outside of the vehicle (within 5 ft (1.5 m) of a Passive Entry door handle).

• The doors are manually locked using the door lock knobs.

• Three attempts are made to lock the doors using the door panel switch, and then the doors are closed.

With one of the JEEP WRANGLER 2022 Passive Entry key fobs within 5 ft (1.5 m) of the driver or passenger front door handles, pushing the Passive Entry lock button will lock the vehicle doors and the swing gate.

DO NOT grab the door handle when pushing the door handle lock button. This could unlock the door(s).

The JEEP WRANGLER 2022 doors can also be locked by using the lock button located on the vehicle’s interior door panel.

The swing gate Passive Entry unlock feature is built into the swing gate handle. With a valid Passive Entry key fob within 5 ft (1.5 m) of the swing gate handle, grab the swing gate handle to unlock the swing gate automatically, and pull the swing gate to open.

The Automatic Door Lock feature on the JEEP WRANGLER 2022 is enabled by default. When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). This feature can be enabled or disabled by an authorized dealer per written request of the customer.

To provide a safer environment for small children riding in the rear seats of the JEEP WRANGLER 2022, the rear doors are equipped with a Child-Protection Door Lock system. To use the system, open each rear door, use a flat-blade screwdriver (or mechanical key) and rotate the dial to the lock or unlock position.

• When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position.

• After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the unlocked position.

• After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the locked position.

• For emergency exit with the system engaged, move the lock lever rearward (located on the door trim panel), roll down the window and open the door with the outside door handle.

Avoid trapping anyone in the JEEP WRANGLER 2022 in a collision. Remember that the rear doors can only be opened from the outside when the Child-Protection locks are engaged (locked). Always use this device when carrying children. After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle. Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle. Before getting out of the car, be sure to check that there is no one left inside.

Do not drive your JEEP WRANGLER 2022 on public roads with the doors removed as you will lose the protection they can provide. This procedure is furnished for use during off-road operation only.

• All occupants must wear seat belts during off-road operation with doors removed.

• Do not store detached doors inside of the JEEP WRANGLER 2022, as they may cause personal injury in the event of an accident.

Doors are heavy; use caution when removing them.

To remove the front doors of the JEEP WRANGLER 2022, proceed as follows:

1. Roll down the glass window to prevent any damage.

2. Remove the hinge pin screws from the upper and lower outside hinges (using a #T50 Torx head driver). The hinge pin screws and nuts can be stowed in the rear cargo tray located under the rear load floor.

3. Remove the plastic wiring access door under the instrument panel by sliding the plastic panel along the door frame toward the seats until the tabs are detached. Do not force open; this will break the plastic cover.

4. Pull up on the red locking tab to unlock the wiring harness.

5. Push and hold down the black security tab under the wiring harness, and lift the harness lever into the open position.

6. With the wiring harness open, pull straight downward on the wiring connector to unplug. Store the wiring connector in the lower door basket.

7. With the door in the open position, remove the check bolt from the door check attachment on the bodyside (using a #T40 Torx head driver). Keep the check arm in the extended position for easier reinstallation.

8. With the door open, lift the door with the help of another person, to clear the hinge pins from their hinges and remove the door. The upper hinge pin is longer, which can be used to assist in guiding the door into place during installation.

1. Locate the upper and lower hinge pins on the door, and lower them into the body hinges on the JEEP WRANGLER 2022. The upper hinge pin is longer, which can be used to assist in guiding the door into place during installation.

2. With the door in the open position, align the door check bracket with the hole on the bodyside. Insert the check screw and tighten using a #40 Torx head driver to 19.9 ft·lb (27.0 N·m).

3. Insert the upper and lower hinge pin screws into the body hinges. Tighten the screws using a #T50 Torx head driver to 3.8 ft·lb (5.2 N·m).

If the check arm is stuck inside the door, follow these instructions to install the check arm:

• Insert the check arm screw into the check arm bracket. Ensure the screw is in the correct orientation.

• Slowly pull on the screw to draw the check arm out until you encounter increased resistance. Do not attempt to pull the check arm all the way out.

• While sitting inside the vehicle, hold the door partially closed and insert the screw into the hole on the body.

• Using your fingers, turn the screw clockwise at least two full turns. Gently pull on the screw to ensure it is secure.

• Using the door handle, slowly push the door open. The check arm will be pulled out of the door. You may hear the check arm pop against the screw.

• Fully tighten the screw as instructed.

To avoid personal injury be sure to keep your arms, hands, fingers and all objects clear of the check arm area during the removal and installation procedures.

Do not close the door before reattaching the door check to the body. Damage may occur to the door check. Do not overtighten Torx fasteners, damage to the vehicle’s parts will occur. Hinge pins can break if overtightened during door install (Max Torque: 6.0 ft·lb/8.1 N·m).

To reinstall the wiring connector on the JEEP WRANGLER 2022 door into the harness just inside the vehicle, proceed as follows:

Make sure there is plenty of slack on the wiring connector during installation. Close the door slightly to provide more slack if needed.

1. With light finger pressure, seat the wiring connector straight into the wiring harness until the wiring harness lever starts to lower with the latching pin.

2. After the harness lever has started to move with the pressure of seating the wiring connector, continue by lowering the wiring harness lever to the fully closed position.

Failure to correctly reconnect the wiring connector into the harness will result in damage that is not covered by the New Vehicle Warranty.

Do not drive your JEEP WRANGLER 2022 on public roads with the doors removed as you will lose the protection they can provide. This procedure is furnished for use during off-road operation only.

Doors are heavy; use caution when removing them. Hinge pin can break if overtightened during door reinstall (Max Torque: 7.5 ft·lb / 10 N·m).

1. Roll down the glass window to prevent any damage.

2. Remove the hinge pin screws from the upper and lower outside hinges (using a #T50 Torx head driver). The hinge pin screws and nuts can be stowed in the rear cargo tray located under the rear load floor.

3. Slide the front seat(s) fully forward.

4. Pry open and remove the plastic wiring access door from the bottom of the B-pillar.

5. Unplug the wiring connector. Squeeze the tab on the base of the wiring harness. This will unlock the connector tab, allowing the wiring connector to be unplugged.

6. Remove the check screw from the center door check (using a #T40 Torx head driver). Keep the check arm in the extended position for easier reinstallation.

7. With the door open, lift the door with the help of another person, to clear the hinge pins from their hinges and remove the door.

To reinstall the door(s), perform the previous steps in the reverse order. The upper hinge has a longer pin, which can be used to assist in guiding the door into place when reinstalling.

If the JEEP WRANGLER 2022 is equipped with the Door Off Mirror Kit, exterior rearview mirrors can be installed on to the upper body door hinges after the front doors have been removed.

To install the Door Off Mirrors, proceed as follows:

1. Remove both front doors.

2. Remove the cowl bolt closest to the door opening using a #40 Torx head driver, and store in a safe location.

3. Push the mirror bracket forward onto the A-pillar, making sure to align the bottom of the bracket with the upper door hinge, and the hole from the removed cowl bolt.

4. Place the bracket bushing behind the mirror bracket (over the cowl bolt hole), then insert the bracket bolt into the mirror bracket, through the bracket bushing.

5. Insert the hinge shoulder bolt through the bottom of the upper door hinge up into the mirror bracket, then rotate the bracket knob toward the rear of the vehicle to secure the mirror bracket to the A-pillar.

6. Tighten both the bracket bolt and the hinge shoulder bolt with a #40 Torx head driver. Recommended torque specification for the bracket bolt is 6 ft-lb (8 N·m), and 7.5 ft-lb (10 N·m) for the hinge shoulder bolt.

7. Lower the mirror assembly onto the mirror bracket.

8. Insert the three mirror screws into the mirror assembly, and tighten into the mirror bracket using a #30 Torx head driver. Recommended torque specification for the mirror screws is 4 ft-lb (5.5 N·m).

9. Repeat the steps on the other side of the vehicle.

If this kit is being installed with the optional lamp bracket, the bracket bushing from step 4 is not needed. Use the spacer from the lamp bracket.

• Careless handling and storage of the half-doors may damage the seals resulting in water leaks into the interior of the JEEP WRANGLER 2022.

• The upper half-doors must be positioned properly to ensure sealing. Improper installation can cause water leaks into the interior of the vehicle.

• Store the zipper pulls of the upper half-door windows at the upper B-pillar area for both front and rear doors to avoid damage to the windows when not in use.

• Do not attempt to operate the half-door zipper in temperatures of 41°F (5°C) or below. Damage to the window may occur.

• Do not run half-doors through an automatic car wash. This may result in scratches and wax buildup on the windows.

• Do not close the door before reattaching the door check to the body. Damage may occur to the door check.

• Do not overtighten Torx fasteners, damage to the vehicle’s parts will occur.

• Hinge pins can break if overtightened during door install (Max Torque: 6.0 ft·lb/8.1 N·m).

To install the front or rear half-doors on the JEEP WRANGLER 2022, proceed as follows:

1. Remove the full doors from the vehicle.

2. Locate the upper and lower hinge pins on the lower half-door, and lower them into the body hinges on the vehicle. The upper hinge pin is longer, which can be used to assist in guiding the door into place during installation.

3. Insert the upper and lower hinge pin screws into the body hinges. Tighten the screws using a #T50 Torx head driver to 3.8 ft·lb / 5.2 N·m.

4. Attach the cloth strap of the lower half-door to the metal hook just inside the vehicle.

5. Connect the wiring harness on the lower half-door to the connection just inside the vehicle. For front doors, make sure the wiring harness is closed completely.

6. Replace wiring access doors.

7. When the half-doors are shipped with the vehicle, the lower half-doors will have plugs in the post holes that must be removed prior to upper half-door installation. To remove these plugs, proceed as follows:

   • Locate the service hole in the center of each plug of the lower half-door (two on each front and rear door).

   • Place a tool (hook tool or trim stick is recommended) in the service hole.

   • Using the tool, slowly pull upwards from the center of the plug to remove.

8. Making sure the window on the upper half-door is completely zipped closed, insert the upper half-door into the lower half-door by placing the posts into the post holes.

9. Push down firmly on the inside of the upper half-door until it is fully seated in the lower half.

Upon first installation of the half-doors, slowly set the door almost to the closing position and check how the door latch aligns with the body striker. Touch condition between these components can result in damage to both the door and the striker.

Only adjust the door to fit correctly against the striker. Do NOT adjust the striker, as this could affect the positioning of the full door.

If the door does not center align between the latch and the striker, proceed as follows:

1. Loosen (do not remove) the four bolts on the door hinges using the provided #T50 Torx head driver.

2. With the bolts loose, hold the door in the almost closed position, and check that the latch and striker align.

3. With the latch and striker aligned, proceed to close the door softly and tighten the hinge bolts to 20.3 ft·lb / 27.5 N·m (Max Torque: 27.3 ft·lb / 37 N·m).

Upon first installation of the half-doors, slowly close each door to check for body contact. Improper setting of the door hinges can cause extreme non-uniform conditions, and result in damage to the body around the door.

If the door does not latch properly after installation, if there is interference between the panels, or if a non-uniform gap around the door is observed when the door is closed (example: door position appears to be low and too far rearward), the position of the door on its hinges may need to be adjusted. To do this, proceed as follows:

1. Loosen (do not remove) the four bolts on the door hinges using the provided #T50 Torx head driver.

Do not adjust the body mounted hinges, or any part of the door latch, as modifications to these parts will affect installation of the full door.

1. With the bolts loose, the door can be moved forward by pushing the door handle toward the front of the vehicle, and/or upward by grabbing the door handle and lifting towards the roof.

2. Once the gaps between the door and vehicle body are uniform around the entire door, tighten the door hinge bolts to 20.3 ft·lb / 27.5 N·m (Max Torque: 27.3 ft·lb / 37 N·m).

If water leaks or wind noise is observed after installation of the half-doors, the seal of the upper half-door to the door opening may need to be adjusted. To determine if the upper half-door needs to be adjusted, proceed as follows:

1. Determine which door is affected.

2. Open the affected door and hold a dollar-size piece of paper along the top of the door opening against the vehicle near where the leak/noise was observed. Make sure half of the paper is above the area where the door seal contacts the door opening, while the other half is below.

3. Close the door on the paper, then pull the paper upward. If the paper moves with little to no effort, the upper half-door will need to be adjusted in that area to increase seal compression.

There is another optional test that can be performed using a flashlight and the help of another person. One person should be inside the vehicle, and move the flashlight around the periphery of the door seal, shining outward. The other person should stand outside of the vehicle and check for light passing by the seal. If light is seen through the seal area, the door will need to be adjusted.

To adjust the seal compression, proceed as follows:

1. Open the door and lift the upper half-door up and away from the lower half. Lay the upper half-door on a clean, dry surface.

2. Using an 8 mm open-end wrench (not provided), loosen the nut located inside the bottom of the upper half-door post, closest to where the “paper test” detected a gap.

3. Using a 3 mm Allen wrench (not provided), rotate the screw on the side of the post counterclockwise (while holding the wrench on the loosened bolt) to increase the seal compression. If needed, rotate clockwise to reduce seal compression.

4. Tighten the nut inside the bottom of the post using the wrench and make sure the screw head is flush to the post. Reinstall the upper half-door.

5. Close the door and repeat the “paper test”. Repeat the adjustment procedure if needed.

6. If needed, add the provided shim to a lower half-door pocket to seal the upper half-door to the roof:

   1. Lift upper half-door up and away from lower half.

   2. Clean the bottom of the door pocket.

   3. Slide the shim onto a pencil or similar tool.

   4. Remove the paper backing from the adhesive side of the shim and place the shim with pencil into the pocket.

   5. Press the shim firmly to the bottom of the pocket, and remove the pencil once the shim is firmly in place.

   6. Replace upper half-door.

If the compression is increased too much on the front upper corner of the rear doors, deformation of the seal will occur.

To remove the half-doors from the JEEP WRANGLER 2022, repeat the installation steps in reverse order.

When removing the upper half-doors, push upward firmly on the middle of the upper half-door until the posts detach from the lower half.

This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping lever is located on the steering column.

To unlock the steering column, push the control handle downward (toward the floor). To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering column in position, push the control handle upward until fully engaged.

Do not adjust the steering column while driving the JEEP WRANGLER 2022. Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.

The steering wheel in the JEEP WRANGLER 2022 contains a heating element that helps warm your hands in cold weather. The heated steering wheel has only one temperature setting. Once the heated steering wheel has been turned on, it will stay on until the operator turns it off. The heated steering wheel may not turn on when it is already warm.

The heated steering wheel control button is located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.

• Press the heated steering wheel button once to turn the heating element on.

• Press the heated steering wheel button a second time to turn the heating element off.

The engine must be running for the heated steering wheel to operate.

• Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater. It may cause burns even at low temperatures, especially if used for long periods.

• Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material. This may cause the steering wheel heater to overheat.

• It is dangerous to ride in a cargo area, inside or outside of the JEEP WRANGLER 2022. In a collision, people riding in these areas are more likely to be seriously injured or killed.

• Do not allow people to ride in any area of your JEEP WRANGLER 2022 that is not equipped with seats and seat belts.

• Be sure everyone in your JEEP WRANGLER 2022 is in a seat and using a seat belt properly.

The seat in the JEEP WRANGLER 2022 can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor. While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward. Release the bar once you have reached the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.

Adjusting a seat while driving the JEEP WRANGLER 2022 may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death.

The driver’s seat height in the JEEP WRANGLER 2022 can be raised or lowered by using the ratcheting handle, located on the outboard side of the seat. Pull upward on the handle to raise the seat, push downward on the handle to lower the seat. Several strokes may be necessary to achieve the desired position.

To recline the seat in the JEEP WRANGLER 2022, pull on the recline strap and lean forward or backward, depending on the direction you would like the seatback to move. Release the strap when the desired position is reached and the seatback will lock into place.

Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death.

The lumbar control knob in the JEEP WRANGLER 2022 is located on the outboard side of the front driver seat. Rotate the control forward to increase and rearward to decrease the desired amount of lumbar support.

Pull upward on the easy entry lever located on the outboard side of the seatback, and slide the entire seat forward. To return the seat to a sitting position, fold the seatback upright until it locks and push the seat rearward until the track locks.

The front passenger seats have a track memory, which returns the seat to its original position.

The recline strap and easy entry lever should not be used during the automatic returning of the seat to its sitting position.

To fold down the rear seat in four-door JEEP WRANGLER 2022 models:

There are two release levers located on each upper outboard side of the rear seat. The larger of the two release levers folds down the seat and the head restraint simultaneously. The smaller lever folds down the head restraint independently for improved visibility.

To fold the seat, lift upward on the large release lever and slowly fold down the seatback. The head restraint will fold automatically with the seat when this lever is pulled.

You may experience deformation in the seat cushion from the seat belt buckles if the seats are left folded for an extended period of time. This is normal. By simply unfolding the seats to the open position, the seat cushion will return to its normal shape over time.

Be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily.

The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.

Raise the seatback and lock it into place. Then, raise the head restraint until it locks into place. If interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position.

Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could be serious injury.

To fold and tumble the rear seat in two-door JEEP WRANGLER 2022 models:

• Prior to folding the rear seat, it may be necessary to reposition the front seats.

• Be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily.

Folding The Rear Seat:

1. Lift the seatback release lever and fold the seatback forward.

2. Slowly flip the entire seat forward.

Using The Retention Straps:

1. There are two retention straps located on the back of the rear seat and two corresponding wire loops located on the back of each B-pillar. Open the hook-and-loop fastener on the strap and thread through the wire loop. Fold the hook-and-loop fastener over to keep the seat in the folded position. This should be done on both sides.

2. To return the seat to its normal upright position, reverse these steps.

Removing The Rear Seat:

1. Push down on the release bar on each side, and pull the seat out and away from the lower bracket.

2. Remove the seat from the vehicle.

3. To reinstall the rear seat, just reverse these steps.

• It is extremely dangerous to ride in a cargo area, inside or outside of a JEEP WRANGLER 2022. In a collision, people riding in these areas are more likely to be seriously injured or killed.

• Do not allow people to ride in any area of your JEEP WRANGLER 2022 that is not equipped with seats and seat belts.

• Be sure everyone in your JEEP WRANGLER 2022 is in a seat and using a seat belt properly.

• In a collision, you or others in your JEEP WRANGLER 2022 could be injured if seats are not properly latched to their floor attachments. Always be sure that the seats are fully latched.

The heated seat control buttons in the JEEP WRANGLER 2022 are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.

• Press the heated seat button once to turn the HI setting on.

• Press the heated seat button a second time to turn the MED setting on.

• Press the heated seat button a third time to turn the LO setting on.

• Press the heated seat button a fourth time to turn the heating elements off.

The engine must be running for the heated seats to operate. The level of heat selected will stay on until the operator changes it.

• Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time.

• Do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat.

The center part of the rear seat in the JEEP WRANGLER 2022 can also be used as a rear armrest with cupholders. To unfold it, grab the pull strap under the head restraint and pull it forward. The cupholder liner can be removed for cleaning.

Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear.

• All occupants, including the driver, should not operate a JEEP WRANGLER 2022 or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a crash.

• Head restraints should never be adjusted while the JEEP WRANGLER 2022 vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious injury or death in the event of a collision.

To raise the head restraint, pull upward on the head restraint. To lower the head restraint, push the adjustment button located on the base of the head restraint, and push downward on the head restraint. The release button does not need to be pushed to adjust the head restraint.

To remove the head restraint, raise it as far as it can go then push the adjustment button and the release button at the base of each post while pulling the head restraint up. To reinstall the head restraint, put the head restraint posts into the holes and push downward. Then adjust it to the appropriate height.

Do not reposition the head restraint 180 degrees to the incorrect position in an attempt to gain additional clearance to the back of the head.

• A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the JEEP WRANGLER 2022. Always securely stow removed head restraints in a location outside the occupant compartment.

• ALL the head restraints MUST be reinstalled in the JEEP WRANGLER 2022 to properly protect the occupants. Follow the reinstallation instructions prior to operating the vehicle or occupying a seat.

The rear seat in two-door JEEP WRANGLER 2022 models is equipped with non-adjustable, but foldable head restraints.

To fold the outboard head restraint, pull on the release strap located on the upper outboard side of each rear seat.

The rear seat in four-door JEEP WRANGLER 2022 models is equipped with nonadjustable, but foldable, outboard head restraints, as well as an adjustable, removable center head restraint.

To fold the outboard head restraint, pull on the inner release lever, located on the upper part of the rear seat.

To return the head restraint to its upward position, lift up on the head restraint until it locks into place.

To raise the center head restraint, lift up on the head restraint. To lower the center head restraint, push the adjustment button, located at the base of the head restraint, and push down on the head restraint.

To remove the center head restraint, push the release button, located on the base of the head restraint, and pull upward on the head restraint.

To install the head restraint, hold the release button while pushing downward on the head restraint.

Lower the center head restraint to avoid contact with the center console when folding the seat down.

The following basic Voice Commands can be given at any point while using your Uconnect system in the JEEP WRANGLER 2022. Push the VR button on the steering wheel. After the beep, say:

• “ Cancel” to stop a current voice session.

• “ Help” to hear a list of suggested Voice Commands.

• “ Repeat” to listen to the system prompts again.

Notice the visual cues that inform you of your Voice Recognition system’s status.

The VR button is used to activate/deactivate your Voice Recognition system in the JEEP WRANGLER 2022.

Helpful hints for using Voice Recognition:

• Reduce background noise. Wind noise and passenger conversations are examples of noise that may impact recognition.

• Speak clearly at a normal pace and volume while facing straight ahead.

• Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.

• You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.

The rearview mirror in the JEEP WRANGLER 2022 can be adjusted up, down, left, and right. The mirror should be adjusted to center on the view through the rear window.

Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield).

The rearview mirror in the JEEP WRANGLER 2022 can be adjusted up, down, left, and right. The mirror should be adjusted to center on the view through the rear window. The mirror automatically adjusts to headlight glare from vehicles behind you. The Automatic Dimming feature is disabled when the vehicle is in REVERSE to improve the driver’s view.

To avoid damage to the mirrors during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.

To access an illuminated vanity mirror in the JEEP WRANGLER 2022, flip down one of the visors and lift the cover.

Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side mirror of the JEEP WRANGLER 2022.

The mirrors in the JEEP WRANGLER 2022 are heated to melt frost or ice. This feature will be activated whenever you turn on the rear window defroster (if equipped).

The power mirror controls in the JEEP WRANGLER 2022 are located on the door panel next to the door handle. The power mirror controls consist of mirror select buttons and a four-way mirror control switch. To adjust a mirror, push either the L (left) or R (right) button to select the mirror that you want to adjust. Using the mirror control switch, push any of the four arrows for the direction that you want the mirror to move.

HomeLink® in the JEEP WRANGLER 2022 replaces up to three hand-held transmitters that operate devices such as garage door openers, motorized gates, lighting, or home security systems. The HomeLink® unit is powered by your vehicle’s 12 Volt battery.

The HomeLink® buttons are located in the overhead console or sun visor and designate the three different HomeLink® channels.

To operate HomeLink®, push and release any of the programmed HomeLink® buttons. These buttons will activate the devices they are programmed to with each press of the corresponding HomeLink® button.

The HomeLink® indicator light is located above the center button.

HomeLink® is disabled when the Vehicle Security system is active.

For efficient programming and accurate transmission of the radio-frequency signal, it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink® system. Make sure your hand-held transmitter is programmed to activate the device you are trying to program your HomeLink® button to. Ensure that your JEEP WRANGLER 2022 is parked outside of the garage before you begin programming.

It is recommended that you erase all the channels of your HomeLink® before you use it for the first time.

To erase all HomeLink® channels in your JEEP WRANGLER 2022, follow this procedure:

1. Place the ignition switch into the ON/RUN position.

2. Push and hold the two outside HomeLink® buttons (I and III) for up to 20 seconds, or until the HomeLink® indicator light flashes.

Erasing all channels should only be performed when programming HomeLink® for the first time. Do not erase channels when programming additional buttons.

Before programming a device to one of your JEEP WRANGLER 2022 HomeLink® buttons, you must determine whether the device has a rolling code or non-rolling code.

Rolling Code Devices

To determine if your device has a rolling code, a good indicator is its manufacturing date. Typically, devices manufactured after 1995 have rolling codes. A device with a rolling code will also have a “LEARN” or “TRAIN” button located where the antenna is attached to the device. The button may not be immediately visible when looking at the device. The name and color of the button may vary slightly by manufacturer. The “LEARN” or “TRAIN” button is not the button you normally use to operate the device.

Non-rolling Code Devices

Most devices manufactured before 1995 will not have a rolling code. These devices will also not have a “LEARN” or “TRAIN” button.

To program any of the HomeLink® buttons to activate your JEEP WRANGLER 2022 garage door opener motor, refer to the following steps:

All HomeLink® buttons are programmed using this procedure. You do not need to erase all channels when programming additional buttons.

1. Place the ignition switch into the ON/RUN position.

2. Place the garage door opener transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink® button you wish to program, while keeping the HomeLink® indicator light in view.

3. Push and hold the HomeLink® button you want to program while you push and hold the garage door opener transmitter button you are trying to replicate.

4. Continue to hold both buttons and observe the HomeLink® indicator light. The HomeLink® indicator light will flash slowly and then rapidly. Once this happens, release both buttons. Make sure the garage door opener motor is plugged in before moving on to the rolling code/non-rolling code final steps.

Rolling Code Garage Door Opener Final Steps

You have 30 seconds in which to initiate rolling code final step 2, after completing rolling code final step 1.

1. At the garage door opener motor (in the garage), locate the “LEARN” or “TRAIN” button. This can usually be found where the hanging antenna wire is attached to the garage door opener motor. Firmly push and release the “LEARN” or “TRAIN” button.

2. Return to the JEEP WRANGLER 2022 and push the programmed HomeLink® button three times (holding the button for two seconds each time). If the garage door opener motor operates, programming is complete.

3. Push the programmed HomeLink® button to confirm that the garage door opener motor operates. If the garage door opener motor does not operate, repeat the final steps for the rolling code procedure.

Non-Rolling Code Garage Door Opener Final Steps

1. Push and hold the programmed HomeLink® button and observe the HomeLink® indicator light. If the HomeLink® indicator light stays on constantly, programming is complete.

2. Push the programmed HomeLink® button to confirm that the garage door opener motor operates. If the garage door opener motor does not operate, repeat the steps from the beginning.

If you unplugged the device for programming, plug it back in at this time.

• Your motorized door or gate will open and close while you are programming the universal transceiver. Do not program the transceiver if people or pets are in the path of the door or gate.

• Do not run your JEEP WRANGLER 2022 vehicle in a closed garage or confined area while programming the transceiver. Exhaust gas from your vehicle contains carbon monoxide (CO) which is odorless and colorless. Carbon monoxide is poisonous and can cause you and others to be severely injured or killed.

• Your motorized door or gate will open and close while you are programming the universal transceiver. Do not program the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features.

The procedure on how to program HomeLink® to a miscellaneous device follows the same procedure as programming to a garage door opener. Be sure to determine if the device has a rolling code, or non-rolling code before beginning the programming process.

Canadian radio frequency laws require transmitter signals to time-out (or quit) after several seconds of transmission, which may not be long enough for HomeLink® to pick up the signal during programming. Similar to this Canadian law, some US gate operators are designed to time-out in the same manner. The procedure may need to be performed multiple times to successfully pair the device to your HomeLink® buttons.

To reprogram a single HomeLink® button that has been previously trained in your JEEP WRANGLER 2022, without erasing all the channels, refer to the following procedure. Be sure to determine if the new device you want to program the HomeLink® button to has a rolling code or a non-rolling code.

1. Place the ignition in the ON/RUN position, without starting the engine.

2. Push and hold the desired HomeLink® button until the HomeLink® Indicator light begins to flash after 20 seconds. Do not release the button.

3. Without releasing the button, proceed with step 2 in “Programming HomeLink® To A Garage Door Opener” and follow all remaining steps.

For programming transmitters in the JEEP WRANGLER 2022 that require the transmitter signals to “time-out” after several seconds of transmission:

Canadian radio frequency laws require transmitter signals to time-out (or quit) after several seconds of transmission – which may not be long enough for HomeLink® to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to time-out in the same manner.

It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor.

1. Place the ignition in the ON/RUN position.

2. Press and hold the desired HomeLink® button until the indicator light begins to flash after 20 seconds. Do not release the button.

3. Without releasing the button, proceed with “Canadian/Gate Operator Programming” step 2 and follow all remaining steps.

It is advised to erase all HomeLink® channels in your JEEP WRANGLER 2022 before you sell or turn in your vehicle.

To do this, push and hold the two outside buttons for 20 seconds until the indicator flashes. Note that all channels will be erased. Individual channels cannot be erased.

The HomeLink® Universal Transceiver is disabled when the Vehicle Security system is active.

The universal garage door opener in the JEEP WRANGLER 2022 only operates when the engine is running for security reasons associated with removable tops and doors.

If you are having trouble programming HomeLink® in your JEEP WRANGLER 2022, here are some of the most common solutions:

• Replace the battery in the garage door opener hand-held transmitter.

• Push the LEARN button on the garage door opener to complete the training for a rolling code.

• Did you unplug the device for programming and remember to plug it back in?

The headlight switch in the JEEP WRANGLER 2022 is located on the left side of the instrument panel. This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, interior lights, and fog lights (if equipped).

For JEEP WRANGLER 2022 vehicles sold in Canada, the headlight switch has an AUTO and ON detent but without an OFF detent. Headlights will be deactivated when the headlight switch is placed in the parking lights position. However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights. The DRLs may be deactivated when the parking brake is engaged.

Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation. Rotate the headlight switch to the second detent for headlight, parking light, and instrument panel light operation.

For JEEP WRANGLER 2022 vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel lights position to the first detent to turn on headlights, parking lights, and instrument panel lights. Rotate the headlight switch to the second detent for the AUTO position.

The Daytime Running Lights (DRLs) in the JEEP WRANGLER 2022 are active when the low beams are not on, and the engine is running. DRLs may be deactivated by applying the parking brake.

For vehicles sold in Canada, the Daytime Running Lights will automatically deactivate when the front fog lights are turned on.

On some JEEP WRANGLER 2022 vehicles, the Daytime Running Lights may deactivate, or reduce intensity, on one side of the vehicle (when a turn signal is activated on that side), or on both sides of the vehicle (when the hazard warning lights are activated).

Push the multifunction lever toward the instrument panel in the JEEP WRANGLER 2022 to switch the headlights to high beams. The lever will return to the centered position. To return the headlights to low beam, pull the lever toward the steering wheel, or push the lever toward the instrument panel.

The Automatic High Beam Headlamp Control system in the JEEP WRANGLER 2022 provides increased forward lighting at night by automatically controlling the high beams through the use of a camera mounted on the vehicle’s header. This camera detects vehicle specific light and automatically switches from high beams to low beams until the approaching vehicle is out of view.

The Automatic High Beam Headlamp Control can be turned on or off by selecting “ON” under “Auto High Beam” within your Uconnect Settings, as well as turning the headlight switch to the AUTO position and placing the multifunction lever in the high beam position.

Broken, muddy, or obstructed headlights and tail lights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly.

You can signal another vehicle in your JEEP WRANGLER 2022 with your headlights by lightly pulling the multifunction lever toward you. This will cause the high beam headlights to turn on, and remain on, until the lever is released.

This system in the JEEP WRANGLER 2022 automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch clockwise to the last detent for automatic headlight operation. When the system is on, the headlight time delay feature is also on. This means the headlights will stay on for up to 90 seconds after you place the ignition into the OFF position. To turn the automatic system off, move the headlight switch out of the AUTO position.

The engine must be running before the headlights will come on in the automatic mode.

If the headlights, parking lights, or cargo lights are left on in the JEEP WRANGLER 2022 after the ignition is placed in the OFF position, a chime will sound when the driver’s door is opened.

To activate the Front Fog Lights in the JEEP WRANGLER 2022, turn on the parking lights or low beam headlights and push the fog light switch. Pushing the fog light switch a second time will turn the front fog lights off.

Move the multifunction lever up or down to activate the turn signals in the JEEP WRANGLER 2022. The arrows on each side of the instrument cluster flash to show proper operation. If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb.

Lightly push the multifunction lever up or down in the JEEP WRANGLER 2022, without moving beyond the detent, and the turn signal will flash three times then automatically turn off.

The courtesy lights in the JEEP WRANGLER 2022 will turn on when the front doors are opened, by rotating the dimmer controls on the headlight switch fully upward, or, if equipped, when the unlock button is pushed on the key fob.

The interior courtesy lights are located in the center of the vehicle’s sport bar, and consist of one large center light and four smaller reading lights. Each reading light can be turned on by pushing the lens. Pushing the lens a second time will turn the light off.

When a door is open and the interior lights are on, rotating the dimmer control to the extreme bottom position will cause all the interior lights to turn off. This allows the doors to stay open for extended periods of time without discharging the vehicle’s battery.

The dimmer controls in the JEEP WRANGLER 2022 are part of the headlight switch and are located on the left side of the instrument panel. With the parking lights or headlights on, rotating the right dimmer control upward will increase the brightness of the instrument panel lights. Rotating the left dimmer control will adjust the interior and ambient light levels (e.g. courtesy lights in the footwell, illuminated cupholders, and front door handles).

The windshield wiper/washer control lever in the JEEP WRANGLER 2022 is located on the right side of the steering column. The front wipers are operated by rotating a switch, located at the end of the lever.

Rotate the end of the lever upward to the first detent past the intermittent settings for low-speed wiper operation. Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper operation.

In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.

Intermittent Wipers

Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. Rotate the end of the lever to the first detent position for one of four intermittent settings. The delay cycle can be set anywhere between 1 to 18 seconds. The wiper delay times depend on vehicle speed. If the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled.

Windshield Washers

To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will start and continue to operate for two or three wipe cycles after the lever is released. Then, the intermittent interval previously selected will resume. If the lever is pulled while in the off position, the wipers will operate for two or three wipe cycles. Then, the wipers will turn off. As a protective measure, the washer will stop if the switch is held for more than 20 seconds. Once the switch is released the washer will resume normal operation.

Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.

Mist

Push upward on the wiper lever to activate a single wipe to clear off-road mist or spray from a passing vehicle. As long as the lever is held up, the wipers will continue to operate. The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The washer function must be used in order to spray the windshield with washer fluid.

A rotary switch on the center portion of the windshield wiper/washer lever controls the operation of the rear wiper/washer function in the JEEP WRANGLER 2022.

Rotate the switch upward to the first detent position for intermittent operation and to the second detent for continuous rear wiper operation.

Push the wiper lever toward the instrument panel to activate the rear washer. The washer pump and wiper will continue to operate as long as the lever is held.

As a protective measure, the washer will stop if the switch is held for more than 20 seconds. Once the switch is released the washer will resume normal operation.

If the rear wiper is operating when the ignition is placed in the OFF position, the wiper will automatically return to the parked position. When the vehicle is restarted, the wiper will resume function at whichever position the switch is set at.

Press and release the MAX A/C button on the touchscreen in the JEEP WRANGLER 2022 to change the current setting to the coldest output of air. The MAX A/C indicator illuminates when MAX A/C is on. Pressing the button again will cause the MAX A/C operation to exit.

The MAX A/C button is only available on the touchscreen.

MAX A/C sets the control for maximum cooling performance. The button illuminates when MAX A/C is on. In MAX A/C, the blower level and mode position can be adjusted to desired user settings. Pressing other settings will cause the MAX A/C to turn off.

Press and release this button on the touchscreen, or push the button on the faceplate, to change the current setting. The A/C indicator illuminates when A/C is on.

The A/C button allows the operator to manually activate or deactivate the A/C system. When the A/C system is turned on, cool dehumidified air will flow through the outlets into the cabin.

Press and release this button on the touchscreen, or push the button on the faceplate, to change the system between recirculation mode and outside air mode. The Recirculation indicator and the A/C indicator illuminate when the Recirculation button is pressed. Recirculation can be used when outside conditions, such as smoke, odors, dust, or high humidity are present. Recirculation can be used in all modes.

Recirculation may be unavailable (button on the touchscreen greyed out) if conditions exist that could create fogging on the inside of the windshield. The A/C can be deselected manually without disturbing the mode control selection. Continuous use of the Recirculation mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. Recirculation mode may automatically adjust to optimize customer experience for warming, cooling, dehumidification, etc. In cold weather, use of Recirculation mode may lead to excessive window fogging.

Set your desired temperature and press and release the AUTO button on the touchscreen, or push the button on the faceplate. AUTO will achieve and maintain your desired temperature by automatically adjusting the blower speed and air distribution. Air Conditioning (A/C) may be active during AUTO operation to improve performance. AUTO mode is highly recommended for efficiency. You can press and release this button on the touchscreen, or push the button on the faceplate, to turn AUTO on. The AUTO indicator illuminates when AUTO is on. Toggling this function will cause the system to switch between manual mode and automatic mode.

Press and release this button on the touchscreen, or push and release the button on the faceplate, to change the current airflow setting to Defrost mode. The Front Defrost indicator illuminates when Front Defrost is on. Air comes from the windshield and side window demist outlets. When the defrost button is selected, the blower level may increase. Use Defrost mode with maximum temperature settings for best windshield and side window defrosting and defogging. When toggling the front defrost mode button, the climate system returns to the previous setting.

Press and release the Rear Defrost button on the touchscreen, or push and release the button on the faceplate, to turn on the rear window defroster and the heated outside mirrors (if equipped). The Rear Defrost indicator illuminates when the rear window defroster is on. The rear window defroster automatically turns off after 10 minutes.

Failure to follow these cautions can cause damage to the heating elements:

• Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water.

• Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window.

• Keep all objects a safe distance from the window.

This provides the driver and passenger with independent temperature control. Push the red button on the faceplate or touchscreen or press and slide the temperature bar towards the red arrow button on the touchscreen for warmer temperature settings. Push the blue button on the faceplate or touchscreen or press and slide the temperature bar towards the blue arrow button on the touchscreen for cooler temperature settings.

The numbers within the temperature display will only appear if your JEEP WRANGLER 2022 is equipped with an Automatic Climate Control system.

Press the SYNC button on the touchscreen to toggle the SYNC feature on/off. The SYNC indicator illuminates when SYNC is on. SYNC synchronizes the passenger temperature setting with the driver temperature setting. Changing the passenger’s temperature setting while in SYNC will automatically exit this feature. The SYNC button is only available on the touchscreen.

Blower Control regulates the amount of air forced through the Climate Control system. Adjusting the blower will cause automatic mode to switch to manual operation. There are seven blower speeds available. The speeds can be selected using either the blower control knob on the faceplate or the buttons on the touchscreen.

• Faceplate: The blower speed increases as you turn the blower control knob clockwise from the lowest blower setting. The blower speed decreases as you turn the blower control knob counterclockwise.

• Touchscreen: Use the small blower icon to reduce the blower setting and the large blower icon to increase the blower setting. The blower can also be selected by pressing the blower bar area between the icons.

Select one of the Mode buttons on the touchscreen or press the Mode button on the faceplate to adjust the airflow distribution. The airflow distribution can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets, and demist outlets.

Panel Mode

Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. The air vanes of the center outlets and outboard outlets can be moved up and down or side to side to regulate airflow direction. There is a shut-off wheel located below the air vanes to shut off or adjust the amount of airflow from these outlets.

Bi-Level Mode

Air comes from the instrument panel outlets and floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Bi-Level mode is designed under comfort conditions to provide cooler air out of the panel outlets and warmer air from the floor outlets.

Floor Mode

Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets.

Mix Mode

Air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield.

Press and release the OFF button on the touchscreen, or push the OFF button on the faceplate to turn the Climate Control ON/OFF.

Temperature Control regulates the temperature of the air forced through the climate system. The temperature increases as you turn the temperature control knob clockwise. The temperature decreases as you turn the temperature control knob counterclockwise.

The numbers within the temperature display will only appear if your JEEP WRANGLER 2022 is equipped with an Automatic Climate Control system.

Turning the temperature control knob clockwise increases the heating temperature and turning the temperature control knob counterclockwise decreases the heating temperature.

To activate Automatic Temperature Control (ATC) in the JEEP WRANGLER 2022:

1. Push the AUTO button on the faceplate, or the AUTO button on the touchscreen on the Automatic Temperature Control (ATC) Panel.

2. Next, adjust the temperature that you would like the system to maintain by adjusting the driver and passenger temperature control buttons. Once the desired temperature is displayed, the system will achieve and automatically maintain that comfort level.

3. When the system is set up for your comfort level, it is not necessary to change the settings. You will experience the greatest efficiency by simply allowing the system to function automatically.

It is not necessary to move the temperature settings for cold or hot vehicles. The system automatically adjusts the temperature, mode, and blower speed to provide comfort as quickly as possible.

To provide maximum comfort in the Automatic mode during cold start-ups, the blower fan will remain on low until the engine warms up. The blower will increase in speed and transition into Auto mode.

You can adjust the temperature in your JEEP WRANGLER 2022 hands-free to keep everyone comfortable while you keep moving ahead. Push the VR button on the steering wheel. After the beep, say one of the following commands:

• “ Set the driver temperature to 70 degrees”

• “ Set the passenger temperature to 70 degrees”

Voice Command for Climate may only be used to adjust the interior temperature of your JEEP WRANGLER 2022. Voice Command will not work to adjust the heated seats or steering wheel if equipped.

For summer operation of the JEEP WRANGLER 2022 climate control system, the engine cooling system must be protected with a high-quality antifreeze coolant to provide proper corrosion protection and to protect against engine overheating. OAT coolant (conforming to MS.90032) is recommended.

To ensure the best possible heater and defroster performance in the JEEP WRANGLER 2022, make sure the engine cooling system is functioning properly and the proper amount, type, and concentration of coolant is used. Use of the Air Recirculation mode during Winter months is not recommended, because it may cause window fogging.

JEEP WRANGLER 2022 vehicle windows tend to fog on the inside in mild, rainy, and/or humid weather. To clear the windows, select Defrost or Mix mode and increase the front blower speed. Do not use the Recirculation mode without A/C for long periods, as fogging may occur.

Make sure the air intake, located directly in front of the windshield in your JEEP WRANGLER 2022, is free of obstructions, such as leaves. Leaves collected in the air intake may reduce airflow, and if they enter the plenum, they could plug the water drains. In Winter months, make sure the air intake is clear of ice, slush, and snow.

The climate control system in the JEEP WRANGLER 2022 filters out dust and pollen from the air. Contact an authorized dealer to service your cabin air filter, and to have it replaced when needed.

While in an Autostop, the Climate Control system in the JEEP WRANGLER 2022 may automatically adjust airflow to maintain cabin comfort. Customer settings will be maintained upon return to an engine running condition.

The glove compartment in the JEEP WRANGLER 2022 is located on the passenger side of the instrument panel. To open the glove compartment, pull the release handle.

Do not operate the JEEP WRANGLER 2022 with a glove compartment in the open position. Driving with the glove compartment open may result in injury in a collision.

The center console in the JEEP WRANGLER 2022 has both an upper and lower storage compartment.

To open the upper storage compartment, lift the top latch. To access the lower storage compartment, lift the bottom latch.

The rear cargo area storage compartment in the JEEP WRANGLER 2022 is located underneath the load floor. To access the storage compartment, lift up on the cargo strap at the rear of the cargo area.

The Media Hub in the JEEP WRANGLER 2022 is located on the instrument panel, below the climate controls. Behind the media hub access door, the Media Hub contains one AUX port, a Type C USB port and one standard USB port. Both USB ports allow you to play music from MP3 players, smartphones or USB devices through the vehicle’s sound system.

Plugging in a smartphone device to a USB port may activate Android Auto™ or Apple CarPlay® features, if equipped.

The Smart Charging USB ports provide power to your device up to an hour after the vehicle is turned off.

• Once a device is connected to the USB port, it will begin charging and is ready for use with the system. Type C and Type A charge-only USB ports can be used at the same time but cannot be used simultaneously while playing media. When both Type C and Type A charge-only USB ports are in use they will be charged at a reduced rate.

• Both ports share a single data connection. The user cannot switch between Type A or Type C. For example, if a device is plugged into the Type A USB port and another device is plugged into the Type C USB port, a message will appear and allow you to select which device to use.

Located inside the center console, a second USB port allows you to play music from USB devices through your JEEP WRANGLER 2022 sound system.

There are two 12 Volt (13 Amp) auxiliary power outlets in the JEEP WRANGLER 2022 that can provide power for accessories designed for use with the standard power outlet adapters.

The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch. Power is available when the ignition switch is in the ON/RUN or ACC position.

On JEEP WRANGLER 2022 vehicles equipped with a rear subwoofer, there is a second power outlet located in the rear cargo area and is powered directly from the vehicle’s battery.

• Do not plug in or remove the external device while driving. Failure to follow this warning could result in a collision.

• To avoid serious injury or death: Do not insert any objects into the receptacles. Do not touch with wet hands. Close the lid when not in use. If this outlet is mishandled, it may cause an electric shock and failure.

• Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded, the fuse protecting the system will need to be replaced.

• Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.

• Many accessories that can be plugged in draw power from the JEEP WRANGLER 2022 vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.

• Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly. Only use these intermittently and with greater caution.

• After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the JEEP WRANGLER 2022 vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle’s battery.

• Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage.

There is a 115 Volt, 150 Watt inverter outlet located on the back of the center console in the JEEP WRANGLER 2022 to convert DC current to AC current. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts. Certain video game consoles exceed this power limit, as will most power tools.

The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter automatically shuts down. Once the electrical device has been removed from the outlet, the inverter should automatically reset. If the power rating exceeds approximately 170 Watts, the power inverter may have to be reset manually.

Four auxiliary switches located in the lower switch bank of the instrument panel in the JEEP WRANGLER 2022 can be used to power various electrical devices. You have the ability to configure the functionality of the auxiliary switches via the Uconnect Settings.

All switches can be configured as follows:

• Switch type operation: Latching or Momentary

• Power source: Battery or Ignition

• Ability to hold last state across key cycles: On or Off

Holding last state conditions are met when switch type is set to latching and power source is set to ignition.

The auxiliary switches manage the relays that power four blunt cut wires. These wires are located under the instrument panel in the passenger compartment and under the hood to the right, near the battery.

In addition to the four auxiliary switch wires, a fused battery wire and ignition wire are also located in the interior, in the passenger side under the instrument panel.

A kit of splices and heat shrink tubing are provided with the auxiliary switches to aid in the connection/installation of your electrical devices.

The wiring chart for the JEEP WRANGLER 2022 auxiliary switches is as follows:

The power window switches in the JEEP WRANGLER 2022 are located on the instrument panel below the climate controls. Push the switch downward to open the window and upward to close the window.

The top left switch controls the left front window and the top right switch controls the right front window.

Never leave children unattended in the JEEP WRANGLER 2022, and do not let children play with power windows. Do not leave the key fob in or near the vehicle, or in a location accessible to children. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death.

The power window switches will remain active for up to 10 minutes after ignition is placed in the OFF position. Opening either front door will cancel this feature.

For Four-Door Models:

The lower left switch controls the left rear passenger window, and the lower right switch controls the right rear passenger window. There are window switches located on the rear of the center console for the rear passenger windows in the four-door model.

The driver door power and the passenger door power window switches in the JEEP WRANGLER 2022 have an Auto-Down feature. Push the window switch down to the second detent and release, and the window will go down automatically. To stop the window from going all the way down during the Auto-Down operation, pull up on the switch briefly.

There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing.

The window lockout switch in the JEEP WRANGLER 2022 allows you to disable the window controls on the rear passenger doors. To disable the window controls, rotate the switch downward. To enable the window controls, rotate the switch upward.

Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your JEEP WRANGLER 2022 vehicle may exhibit wind buffeting with the windows down in certain open or partially open positions. This is a normal occurrence and can be minimized by adjusting the window opening.

For your convenience, a tool kit is provided with your JEEP WRANGLER 2022 vehicle located in the center console. This kit includes the necessary tools required for the operations described in the following sections. All pieces fit into the ratchet for easy use.

The soft top and the hard top are to be used independently. Your JEEP WRANGLER 2022 vehicle warranty will not cover damage resulting from both tops being installed at the same time.

The following options are available to you when lowering the JEEP WRANGLER 2022 soft top:

• Sunrider® position with rear and quarter windows installed

• Sunrider® position with rear and quarter panels removed

• Sunrider® position with rear window installed and quarter panels removed

• Fully lowered position with rear and quarter windows removed

Both quarter windows should be removed and installed together.

To lower the Soft Top into Sunrider® Position:

1. Fold both sun visors forward against the windshield.

2. Release the header latches from the crossbar by pulling the handle downward. Make sure the hook is disengaged from its receiver.

3. From both the left and right sides, lift up on the #1 Bow of the soft top to start the operation.

4. Move to the side of the vehicle and use the side link to fold the soft top rearward into the Sunrider® position.

If leaving the soft top in the Sunrider® position, secure the top by using the two hook-and-loop fasteners provided in the center console.

• The JEEP WRANGLER 2022 vehicle can be driven in the Sunrider® position with the rear window and quarter panel assemblies fully installed or completely removed.

• The rear window and rear quarter windows must be removed before fully lowering the soft top to prevent damage to the top. Clean the side and rear windows before removal to assist in preventing scratching during removal of the soft top. If the plastic retainers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush.

The fabric quarter windows and fabric top are designed only for protection against the elements. Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident. Remember, always wear seat belts. Make sure hands and fingers are clear of all pinch points when installing and removing the soft tops. The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.

The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).

If the temperature is below 72°F (24°C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up. This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top. Place the JEEP WRANGLER 2022 vehicle in a warm area. Pull steadily on the top fabric. The vinyl will stretch back to its original size and the top can then be installed. If the temperature is 41°F (5°C) or below, do not attempt to put the top down or roll the rear or side curtains.

Do not run a fabric top through an automatic car wash. Window scratches and wax buildup may result. Do not lower the top when the temperature is below 41°F (5°C). Damage to the top may result.

Do not move your JEEP WRANGLER 2022 vehicle until the top has been either fully attached to the windshield frame, or fully lowered.

Do not fully lower the top with the windows installed. Window and top damage may occur.

Do not use any tools (screwdrivers, etc.) to pry or force any of the clamps, clips, or retainers securing the soft top. Do not force or pry the soft top framework when opening or closing. Damage to the top may result.

It is recommended that the top be free of water prior to opening it. Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the JEEP WRANGLER 2022 interior. Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle’s interior.

The soft top must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicle’s interior.

Before fully lowering the soft top of the JEEP WRANGLER 2022, the rear window and rear quarter windows must be removed.

Remove The Rear Window:

1. With the swing gate open, remove the rear window’s plastic retainers from the lower right and left corners.

2. Grab the swing gate bar, rotate it outward and upward releasing it from both the right and left retainers.

3. While holding the window in place, slide the swing gate bar to the left separating it from the rear window. Store in soft window bag (if equipped), or a safe location.

While keeping the rear window level, slide to the left until it is completely separate from its retainer. Do not pull downward while removing the rear window. Damage to the retainer could result.

Remove The Right And Left Quarter Windows:

1. Through the rear opening, push the bottom corner outward and release tab from the bottom of the window pillar.

2. Undo the hook-and-loop fastener located at the upper front corner of each quarter window.

3. Starting at the rear of the vehicle, remove plastic retainer from along the bottom of the window moving toward the front of the vehicle.

4. Remove plastic retainer from the bottom to the top of the front window.

While keeping the window level, slide rearward until it is completely separate from its retainer. Do not pull downward while removing the window. Damage to the retainer could result.

Store in soft window bag (if equipped) or a safe location.

To safely store the soft top rear window, and rear quarter windows in the JEEP WRANGLER 2022, proceed as follows:

The swing gate bar, once removed from the rear window, does not store in the soft window storage bag (if equipped).

1. With the bag opened completely, fold both fabric dividers downward and lay the first quarter window all the way to the right side with the inside of the window facing downward and the window pillar to the outside. The quarter windows are marked “1” and “2” on the inside of the window pillar.

2. Fold the first divider upward, covering the first quarter window.

3. Lay the second quarter window on top of the first divider all the way to the left side with the inside of the window facing downward and the window pillar to the outside.

4. Fold the second divider upward, covering the second quarter window.

5. Lay the rear window on top of the second divider.

6. Close the storage bag and store in a safe location.

To fully lower the soft top in the JEEP WRANGLER 2022, follow these steps:

1. Remove the rear window and quarter panel windows.

2. From the Sunrider® position, remove straps if previously secured and move to the rear of the vehicle.

3. Locate the Sunrider® latch beneath the #6 Bow of the soft top on the left side.

4. Pull the latch to release the top, and allow the soft top to slide rearward freely in the guide tracks to the stowed position. Failure to follow the next steps could result in damage to the Soft Top or vehicle.

5. While pushing downward slightly on the folded soft top, slide the lock lever on the left and right side lift assist mechanisms to the “lock” position.

6. Once the lock lever is in the “lock” position, push downward on each side of the folded soft top to ensure it is secure. An audible “click” may be heard.

To raise the Soft Top from the fully lowered position in the JEEP WRANGLER 2022:

1. From the fully lowered position, remove straps if previously secured. Failure to follow the next steps could result in damage to the Soft Top or vehicle.

2. While pushing down on the rear of the top, slide the lock lever on the left and right side lift assist mechanisms to the “unlock” position.

3. Push up and forward from the #5 Bow along the guide track until it locks into the Sunrider® position with an audible “click”.

4. Gently pull rearward on the #6 Bow to ensure the top is locked in the Sunrider® position.

5. Using the side link, lift and push the soft top toward the front of the vehicle manually guiding the top into the closed position.

6. From inside the vehicle, pull the handle on the header latch downward to engage the hook into its receiver. Repeat on the other side.

7. Pull the handle back upward while squeezing the hook, locking the latch into place.

Secure the top by using the two hook-and-loop fasteners provided in the center console.

To install the Right and Left Quarter Windows in the JEEP WRANGLER 2022:

1. From the rear of the vehicle, guide the top of the window into the retainer and slide forward while keeping the window level. Repeat on the other side.

2. Place the top of the quarter window pillar into the top cover, and insert the bottom tab into the clip.

3. Engage the retainers on the front of the windows, ensuring they are fully engaged, followed by the retainers along the bottom of the windows.

4. Secure the hook-and-loop fastener at the upper front corner of each quarter window by pressing firmly.

It is critical that the retainers are fully engaged before the JEEP WRANGLER 2022 vehicle resumes motion. Failure to follow all Quarter Window Install steps could result in damage to the Soft Top or vehicle.

To install the Rear Window in the JEEP WRANGLER 2022:

1. Guide the rear window into the retainer from left to right while keeping the window level.

2. Insert the swing gate bar into the retainers at the bottom of the window from left to the right.

3. Rotate the swing gate bar into the left and right side retainers.

4. Line up the rear window to the right side quarter window first, and engage the plastic retainers.

5. Repeat with the left side quarter window.

6. Engage the rear window retainers in the lower right and left corners.

To remove the Soft Top from the JEEP WRANGLER 2022:

1. Fully lower the soft top.

2. Make sure the lift assist mechanism on both the left and right sides are in the “lock” position, and an audible “click” is heard when pushing down on the #1 bow from each of the lift assist mechanisms before removing.

3. Using the provided #40 Torx head driver and ratchet, unscrew the two Torx head screws on each lift assist mechanism, then lift the mechanism up and away from the vehicle.

4. Pull the release lever on top of the rail rearward to release the side link from the track.

5. Repeat on the opposite side.

6. Utilizing two people, lift the soft top up and away from the vehicle, careful to avoid the vehicle’s sport bar, trim, and tire carrier. Store the soft top in a safe, clean, and dry location.

7. Using the provided #50 Torx head driver and ratchet, unscrew the Torx screw on both rear corners of the vehicle, removing the retainers.

Failure to follow the next steps could result in damage to the Soft Top or vehicle.

To install the Soft Top on the JEEP WRANGLER 2022:

If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top.

To install the soft top, place the soft top on the vehicle while making sure that the top is sitting flush with the body at the sides and check to ensure that there is a uniform gap between the lift glass and hard top. Then follow the removal steps in reverse order.

• Inspect the hard top seals for damage and replace if necessary.

• The Torx fasteners that attach the hard top to the body should be torqued as follows using the provided #50 Torx head driver and ratchet:

  • Hard top to B-pillar: 119 in-lb +/- 23 in-lb (13.5 N·m +/- 2.7 N·m)

  • Hard top to J-rail: 154 in-lb +/- 30 in-lb (17.5 N·m +/- 3.5 N·m)

1. If currently installed, remove the hard top.

2. Install the door rails, starting with the front, followed by the rear on each side.

3. Install the rear retainers on each side of the rear of the vehicle using the provided #50 Torx head driver and ratchet.

4. Making sure the lift assist mechanism is in the “lock” position, lift the soft top into the rear of the vehicle with the side links pointing toward the front. Lower the lift assist mechanisms onto its retainers on both sides (on the inside of the sport bar).

5. Using the provided #40 Torx head driver and ratchet, tighten the Torx screws by turning them clockwise. Secure them until they are snug, being careful not to cross-thread the screws or overtighten. Repeat on the opposite side.

6. While pulling the release lever on the top of the rail rearward, place the side link into the guide track on the top of the rail then release the lever.

7. Unsnap and remove the black boot cover. This cover should be discarded. It was intended as a protective cover for shipping only.

8. Raise the soft top.

Do not overtighten Torx screws. Damage to the retainers will occur. Failure to follow the next steps could result in damage to the Soft Top or vehicle. Be sure the wire harness in the left rear corner is not tangled in the soft top bows before you lift the top.

To remove the hard top front panel(s) from the JEEP WRANGLER 2022, proceed as follows:

• The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc. For optional Mopar® accessory roof racks.

• Do not move your JEEP WRANGLER 2022 vehicle until the top has been either fully attached to the front header, sport bar, and body side or fully removed.

Failure to follow these cautions may cause interior water damage, stains or mildew:

• It is recommended that the top be free of water prior to panel removal. Removing the top, opening a door or lowering a window while the top is wet may allow water to drip into the JEEP WRANGLER 2022 interior.

The hard top assembly must be positioned properly to ensure sealing. Improper installation can cause water to leak into the JEEP WRANGLER 2022 interior.

• Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the JEEP WRANGLER 2022 interior.

• The front panel(s) must be positioned properly to ensure sealing. Improper installation can cause water to leak into the JEEP WRANGLER 2022 interior.

1. Fold down the sun visor against the windshield.

2. Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.

3. Unlatch the left side header panel latch located at the top of the windshield.

4. Remove the left side panel.

5. Repeat the previous steps to remove the right side panel.

The Freedom Top panels storage bag allows you to store your JEEP WRANGLER 2022 hard top panels. The storage bag contains two compartments.

Lay the bag for the Freedom Top panels down so the loops and hooks are facing upward. Unzip the bag and fold back the outer flap.

Ensure the front panel latch is closed prior to inserting the panel into the panels bag.

1. Insert the left side hard top panel into the bag with the latches facing upward.

2. Unfold the black panel divider (ensure the divider is lying flat).

3. Insert the right side Freedom Top panel into the bag with the latches facing downward. Ensure the front panel latch is closed prior to inserting the panel into the bag.

4. Unfold the outer flap and zip the hard top bag closed.

5. Lift the Freedom Top bag into the JEEP WRANGLER 2022 vehicle with the hooks and straps facing the back of the rear seat. Attach the clip at the bottom of the bag to the child restraint anchorage, located at the base of the rear seat.

6. Wrap the upper strap around the rear head restraints and loop the strap through the buckle. Pull on the strap to tighten the Freedom Top bag securely against the rear seat.

To install the hard top front panel(s) in the JEEP WRANGLER 2022:

1. Open the header latch inside the vehicle, and the three L-shaped locks on each panel.

2. Set the right side panel on the windshield frame with the locating pin in the front receiver mounting hole followed by the left side panel, making sure there is no overhang. Also, make sure that the panels are sitting flush with the body.

3. Reinstall the panel(s) using the same steps for removal in reverse order.

To prevent water leaks, the seals and hard top panels should be clear of any dust and debris prior to reinstallation.

To remove the Hard Top from the JEEP WRANGLER 2022:

1. Remove both front panels.

2. Open both front doors.

3. Using the provided #50 Torx head driver and ratchet, remove the two Torx head screws that secure the hard top at the B-pillar (near the top of the front doors).

4. Remove the six Torx head screws that secure the hard top to the vehicle (along the interior bodyside — three screws on each side) using the #50 Torx head driver.

5. Open the swing gate all the way to ensure clearance of the rear window glass. Lift the rear window glass.

6. Locate the wire harness and washer hose on the left rear inside corner of the vehicle.

7. Release the locking tab by pushing it downward.

8. To remove the wiring harness, push the tab inward while pulling downward to disconnect.

9. To remove the washer hose, push the release button on hose connector, and pull downward.

10. Secure the wire harness to the body side by plugging it into the receptacle and reengaging the locking tab.

11. Secure the washer hose by snapping it into the top of the body side receptacle.

12. Lower the rear window, and close the swing gate.

13. Remove the hard top from the vehicle. Place the hard top on a soft surface to prevent damage.

The removal of the rear Hard Top requires four adults, one located on each corner. Failure to follow this caution could damage the Hard Top.

The Sunrider® soft top in the JEEP WRANGLER 2022 can be used in place of the Hard Top Freedom Panels for quick and easy opening of the area above the driver and front passenger seats.

Do not open or close the Sunrider® top while driving the JEEP WRANGLER 2022. Operating the top while driving could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.

To install the Sunrider® soft top, proceed as follows:

1. Remove both front Hard Top Freedom panels.

2. With the help of a second person, set the Sunrider® top onto the top of the vehicle making sure to align the holes at the front and rear of the side rails.

3. Swing the front frame bracket around the side of the rail, and insert the door rail attachment bolt (provided bolt without spacer) from underneath. Tighten with a #40 Torx head driver until snug.

4. Insert the rear door rail attachment bolt (provided bolt with spacer) from underneath. Tighten with #40 Torx head driver until snug. The recommended torque specification for the front and rear door rail attachment bolts is 8.8 ft-lb (12 N·m).

5. Repeat steps 3 and 4 on the other side of the vehicle.

6. Attach the rear clamp at the rear center of the Sunrider® top using the two provided rear clamp attachment bolts. Tighten with #40 Torx head driver until snug. The recommended torque specification for the rear clamp attachment bolts is 3.7 ft-lb (5 N·m).

7. From inside the vehicle, lift and pull the Sunrider® top forward using the integrated handle on the front header of the top. Manually guide the top into the closed position.

8. From inside the vehicle, pull the handle on the header latch downward to engage the hook into its receiver. Pull the handle back upward while squeezing the hook, locking the latch into place. Repeat on the other side.

To open the Sunrider® top on the JEEP WRANGLER 2022, proceed as follows:

1. Fold both sun visors forward against the windshield.

2. Release the header latches from the crossbar by pulling the handle downward. Make sure the hook is disengaged from its receiver.

3. From the front of the Sunrider® top, lift and push the top rearward to the Sunrider® position.

4. Secure the top by using the two hook-and-loop fasteners provided with the Sunrider® kit, and wrap one around the side rails on each side of the Sunrider® top to hold it in place.

If your JEEP WRANGLER 2022 is equipped with a Power Sliding Top, the control switch can be found on the front trim panel, to the right of the driver’s side sun visor.

Lowering of the windshield is NOT recommended in vehicles equipped with a Power Sliding Top. Damage will occur to the top as well as the header seal.

• The power top is non-removable. If desired, the rear quarter windows can be removed and stored in the provided storage bag.

• The power top will not open in temperatures below -4°F (-20°C). However, if it is opened at a higher temperature, it can be closed at temperatures above -40°F (-40°C).

• The power top will not operate at vehicle speeds above 60 mph (96 km/h).

A slight pause in audio may be heard when opening and closing the Power Sliding Top as a result of the Uconnect system switching between power top Closed and power top Open audio modes.

Express Open/Close

Push the open switch and release it within one-half second and the power top will open automatically from any position. The power top will open fully and stop automatically.

Push the close switch and release it within one-half second and the power top will close automatically from any position. The power top will close fully and stop automatically.

During Express Open or Express Close operation, any other movement of the power top switch will stop the power top.

Manual Open/Close

To open the power top manually, push and hold the open switch to the full open position, then release.

To close the power top manually, push and hold the close switch to the fully closed position, then release.

Any release of the switch during open or close operation will stop the power top movement. The top will remain in a partially opened position until the switch is operated and held again.

This feature will detect an obstruction in the opening of the power top during Express Close operation. If an obstruction in the path of the power top is detected, the power top will automatically retract. Remove the obstruction if this occurs. Next, push the close switch and release to Express Close.

There is no anti-pinch protection when the power top is almost closed. To avoid personal injury be sure to clear your arms, hands, fingers and all objects from the top’s path before closing.

• The Power Sliding Top may reverse motion if closing during a severe headwind. If this occurs, push and hold the Power Sliding Top switch again to close the top completely.

• If three consecutive power top close attempts result in Pinch Protect reversals, Pinch Protect will disable and the power top must be closed in Manual Mode.

Use only a non-abrasive cleaner and a soft cloth to clean the quarter window glass panel.

The power top switch in the JEEP WRANGLER 2022 can remain active in Accessory Delay for up to approximately 10 minutes after the vehicle’s ignition is placed to the OFF position. Opening either front door will cancel this feature.

For JEEP WRANGLER 2022 vehicles equipped with a power top, there is a relearn procedure that allows you to calibrate the power top when the “Express Mode” stops working. To reset the power top, follow these steps:

1. Place the ignition in the RUN position, and start the vehicle. The engine must be running to perform the relearn procedure.

2. Ensure the power top is in the fully closed position.

3. Push and hold the Close switch for 10 seconds. This will put the power top into calibration mode.

4. Continue holding down the close button while the top goes fully open and then back to fully close.

5. Once the power top has stopped in the fully closed position, release the close button. The power top is now reset and ready to use.

If the close button is released anytime during the relearning process, the relearn may not be complete, and the procedure must be repeated.

On JEEP WRANGLER 2022 vehicles equipped with a Power Sliding Top, the rear quarter windows can be removed. To remove these windows, follow this procedure:

1. Open the swing gate, and lift the rear window.

2. Open both side doors nearest the quarter windows.

3. Locate the rear quarter window latches (two on each window) on the interior of the windows.

4. Rotate the left hand side latch clockwise to release.

5. Rotate the right hand side latch counterclockwise to release.

6. From the outside of the vehicle, lift each window upward and away from the vehicle. Do not pull down or apply any weight to the windows after the latches are released. Damage could result to the pins holding the windows in place.

7. Store the rear quarter windows in the provided storage bag and keep in a safe location, or securely fasten the bag to the rear seat.

To use the storage bags for the rear quarter windows in the JEEP WRANGLER 2022, proceed as follows:

The swing gate bar, once removed from the rear window, does not store in the soft window storage bag (if equipped).

1. With the bag completely open and the fabric divider raised, place the first quarter window with the latches facing outward into the foam insert. Fold divider over the window once placed inside. The quarter windows are marked “1” and “2” on the inside of the window pillar.

2. Place the second window into the foam insert with the latches facing outward. Fully close the bag. Once both windows are placed inside the bag, the outside of the windows will be facing each other with all latches facing the outside of the bag.

3. Store the bag in a safe location, or in the cargo area of the JEEP WRANGLER 2022 vehicle by securing the bag in the vehicle’s cargo area. This is done by attaching the straps at the top of the bag to the rear head restraints, as well as attaching the clip at the bottom of the bag to the forward most cargo hook on the load floor.

• Do not drive your JEEP WRANGLER 2022 on public roads with the door frame(s) removed as you will lose the protection that they can provide. This procedure is furnished for use during off-road operation only.

• Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the JEEP WRANGLER 2022 vehicle’s interior.

• The door frame(s) must be positioned properly to ensure sealing. Improper installation can cause water to leak into the JEEP WRANGLER 2022 vehicle’s interior.

In four-door JEEP WRANGLER 2022 models, the rear door frames must be removed first, followed by the front door frames.

1. Using the provided #40 Torx head driver and ratchet, loosen the Torx screws located on the underside of each door frame (two per door). Screws will not fall out once completely loose, as they are held in place by an internal mechanism.

2. Once all the way loosened, remove the screws by pulling downward.

3. Lift the frame upward, removing it from the vehicle.

4. Store screws in a secure location.

5. Repeat procedure on the front door frame (four-door models).

It is necessary to follow these steps to be certain that the transfer case is fully in (N) Neutral before recreational towing to prevent damage to internal parts.

To install the front door rails in four-door JEEP WRANGLER 2022 models, proceed as