DYSON V8 (01) PDF MANUAL

DYSON V8 (01) PDF SUMMARY:

How do I start cleaning with the Dyson V8?

Pull the trigger to start cleaning.

---

How do I switch between power modes?

Toggle between Powerful mode – for longer suction – and MAX mode, for stronger suction by holding down the trigger and sliding the control back and forth. Slide the control to the left for powerful cleaning and to the right for max mode.

---

How do I switch accessories quickly?

The quick-release tools click into place, and release in moments by simply depressing the release switch.

---

How do I clean awkward spaces?

Remove the wand and connect your chosen tool directly to the inlet pipe to use the vacuum as a handheld.

---

What should I check before vacuuming my floors?

Check that the underside of the cleaner head or tool is clean and free from any objects that may cause damage. Before vacuuming your flooring, rugs, and carpets, check the manufacturer’s recommended cleaning instructions.

---

Can the brush bar damage my flooring?

The brush bar on your machine can damage certain flooring. Some rug materials may fuzz if a rotating brush bar is used when vacuuming. If this happens, it is recommended to vacuum without the motorized floor tool and consult with the flooring manufacturer.

---

How do I charge my machine?

Fully charge your machine before your first use. Connect to charger either directly or in the dock. A full charge will take approximately 4.5 hours.

---

How will I know when the battery is charging?

While your battery is charging, the LEDs will flash with the current level of charge. These lights will turn off once your machine is fully charged.

---

What do the battery LEDs mean?

• One flashing blue light indicates a low charge.
• Two flashing blue lights indicate a medium charge.
• Three flashing blue lights indicate a nearly full charge.
• All LEDs lit with a solid blue light indicate a full charge.
• One flashing red LED indicates a battery fault.
• During use, one blue LED lit indicates a low charge.
• During use, two blue LEDs lit indicate a medium charge.
• During use, high charge is indicated when all LEDs are lit.
• No lights illuminated indicates an empty battery.

---

When should I empty the bin?

Empty as soon as the dirt reaches the MAX level – don’t overfill. Using your machine when the dirt is above the MAX line may affect the performance and require more frequent filter washing. Empty the bin as soon as the dirt reaches the MAX mark.

---

How do I empty the bin?

1. Remove the wand from your machine.
2. Hold your machine over the bin and pull the bin release catch upwards. The cyclone will slide up and the bin base will open.
3. Cover your bin tightly in a dustproof bag while you empty. Remove the bin carefully, seal the bag tightly and dispose.
4. Push the bin base upwards until it closes securely.
5. Close the bin by pushing down on the cyclone until it slides into position.

---

How do I clean the bin?

1. Remove the wand from your machine.
2. Hold your machine over a bin and pull the bin release catch upwards. The cyclone will slide up and the bin base will open.
3. Pull the bin release catch upwards. The cyclone will slide up and the bin base will open.
4. Locate the cyclone release button behind the cyclone and push to remove the cyclone from your machine.
5. Pull back on the red catch located on the base, slide the bin down and pull it off your machine.
6. Wipe your bin with a damp, lint-free cloth. Don’t put the bin in a dishwasher or use detergents, polishes or air fresheners.
7. Make sure the bin is completely dry before replacing.
8. Align the tabs on the bin with the grooves on the main body and slide it upwards until it clicks into place.
9. Slide the cyclone into the grooves of the main body and push down until it is in position.
10. Push the bin base up until it clicks firmly shut.

---

What should I do before looking for blockages?

Disconnect your machine from the charger before looking for blockages. Be careful not to touch the trigger and be aware of sharp objects. Leave your machine to cool down before looking for blockages. Do not use your machine when looking for blockages as this could cause injury.

---

What happens if there is a blockage?

Your machine is fitted with an automatic cut-out. If any part of it is blocked, your machine’s motor will pulse and won’t function until the blockage has been cleared.

---

Where should I check for blockages?

Check for blockages at both ends of the wand with the wand removed from the machine. Check for blockages in the cleaner head, tools and main body of your machine.

---

How do I remove filter A for washing?

Lift the filter out of the top of the cyclone. Twist your filter counter-clockwise and pull it away from your machine.

---

How do I wash filter A?

1. Hold the open end of the filter under a running tap, until the water runs clear.
2. Run water over the outside of the filter until the water runs clear.
3. Turn the filter upside down and tap it to remove excess water.
4. Squeeze and twist with both hands to make sure the excess water is removed.

---

How do I dry filter A?

Leave your filter to dry for at least 24 hours in a well-ventilated, warm place. Do not dry your filter in a tumble-dryer or near a naked flame. The filter must be completely dry before putting it back into the machine. Your machine could be damaged if used with a damp filter.

---

How do I reassemble filter A?

1. Align the arrow on the top of the filter with the bin release button.
2. Push down to fit securely in place.
3. Place your filter on your machine, aligned in the open position.
4. Twist clockwise until it clicks securely into position.

---

How do I wash filter B?

1. Wash the inside of the filter under cold, running water, rotating the filter to make sure all the inside is clean.
2. Repeat until the water runs clear.
3. Empty the filter and shake firmly to remove excess water.
4. Keep shaking it until there’s no water coming from the filter.

---

How do I dry filter B?

Leave your filter to dry for at least 24 hours in a well-ventilated, warm place. Do not dry your filter in a tumble-dryer or near a naked flame. The filter must be completely dry before putting it back into the machine. Your machine could be damaged if used with a damp filter. Place your filter, with the open end facing up, to dry.

---

How do I maintain the Motorbar™ cleaner head?

Check your brush bar regularly and clear any obstructions.

---

Is the Motorbar™ cleaner head washable?

No, the Motorbar™ cleaner head and brush bar aren’t washable. Wipe over with a damp lint-free cloth.

---

How do I clear obstructions from the Motorbar™ cleaner head?

1. Make sure your machine is disconnected from the charger and take care not to touch the trigger.
2. Press the cleaner head release button on the end of the wand.
3. Place the cleaner head upside down.
4. Use a coin to unlock the end cap.
5. Twist the end cap and remove it from your brush bar. Don’t wash the end cap.
6. Slide your brush bar out of the cleaner head.
7. Clear any debris from your brush bar.
8. Check inside the cleaner head and remove any debris or blockages.
9. Push the end cap back on to your brush bar and slide it back into the cleaner head.
10. Turn the end cap clockwise into the locked position.

---

How do I maintain the Hair screw tool?

Check your brush bar regularly and clear any obstructions.

---

Is the Hair screw tool washable?

No, the Hair screw tool isn’t washable. Wipe over with a damp lint-free cloth.

---

How do I clear obstructions from the Hair screw tool?

1. Make sure your machine is disconnected from the charger and take care not to touch the trigger.
2. Remove the Hair screw tool from the wand or machine.
3. Push the base plate open.
4. Press the red lever down to release the cleaner head cover.
5. Pull the cleaner head cover off the main body of the tool.
6. Pull your brush bar firmly to remove it from the main body.
7. Check and remove any obstructions from all three parts of your Hair screw tool.
8. Put your brush bar back into position and press firmly until it clicks back into position.
9. Check the red locking lever is in the unlocked position. Align the cleaner head cover with the guide on the main body.
10. Push it down until it clicks into position.
11. Push the red locking lever up until it clicks into position and push the base plate back into place.
12. Slide the housing back on to the brush bar and push the lever on the back of the Hair screw tool upwards to lock.

---

How do I wash the Fluffy™ cleaner head brush bar?

1. Make sure your machine is disconnected from the charger and take care not to touch the trigger.
2. Press the cleaner head release button on the end of the wand.
3. Place the cleaner head upside down.
4. Push the end cap up fully and pull the brush bar out of the cleaner head.
5. Remove the end cap from the brush bar. Don’t wash the end cap.
6. Hold your brush bar under running water and gently rub to remove any lint or dirt.
7. Remove as much excess water as possible, run your hand down the length of the brush bar to squeeze out the water.
8. Before replacing, check that your brush bar is completely dry.

---

How do I dry the Fluffy™ cleaner head brush bar?

Stand your brush bar upright, with the closed end at the top. Leave to dry completely for at least 24 hours.

---

How do I reassemble the Fluffy™ cleaner head brush bar?

1. Reattach the end cap to your brush bar.
2. Slide your brush bar into the cleaner head.
3. Push the end cap back down to the closed position.
4. The end cap should be attached to the cleaner head at an angle less than 90°.

---

How do I clean the tools?

Wipe with a damp, lint-free cloth, without touching the connector end. Make sure your tools are completely dry before using. Do not put any part of your machine in a dishwasher or use detergents, polishes or air fresheners.

---

How do I look after my machine?

Clean it regularly and check for blockages. Wash your filter regularly and leave to dry completely. If your machine is dusty, wipe with a damp lint-free cloth. Do not use detergents or polishes to clean your machine.

---

How do I look after the battery?

To get the best performance and life from your battery, use Powerful suction mode. Your machine won’t operate or charge if the ambient temperature is below 5°C (41°F).