DYSON V15 DETECT (01) PDF MANUAL

DYSON V15 DETECT (01) PDF SUMMARY:

How do I get started with my Dyson V15 Detect?

Refer to the “Getting started” section of the user manual.

---

What items are included in the box?

The box contains:

• Vacuum cleaner with click-in battery
• Wand
• Laser Slim Fluffy™ cleaner head
• High torque cleaner head with anti-tangle comb
• Combination tool
• Crevice tool
• Hair screw tool

Some tools may not be included, but additional tools can be purchased at http://www.dyson.com. These additional tools may include:

• Additional click-in battery
• Soft dusting brush
• Extension hose
• Up-top adapter
• Low-reach adaptor
• Stubborn dirt brush
• Light pipe crevice tool
• Mattress tool

---

What is the combination tool?

The combination tool has a wide nozzle and brush for quick switching between cleaning and dusting tasks in your home or car.

---

What is the soft dusting brush?

The soft dusting brush is enclosed in a skirt of soft nylon bristles for gentle, vacuum-assisted dusting.

---

What is the extension hose?

The extension hose adds up to 61cm of flexible reach to any tool attachment, to clean up high or down low in your home or car.

---

What is the up-top adapter?

The Up-top adapter twists into different positions and angles for easy high-reach cleaning.

---

What is the low-reach adaptor?

The low-reach adaptor bends to comfortably reach down low and is engineered to clean further under low furniture by adjusting the wand angle up to 90°.

---

What is the crevice tool?

The crevice tool is engineered for precise cleaning around tricky edges and into hard-to-reach narrow spaces.

---

What is the stubborn dirt brush?

The stubborn dirt brush has stiff nylon bristles that dislodge ground-in dirt from coarse carpets and high traffic areas.

---

What is the hair screw tool?

The anti-tangle conical brush bar spirals hair off and into the bin, and it is motor-driven for cleaning smaller spaces.

---

What is the light pipe crevice tool?

The crevice tool with LED lights lets you reach into dark, narrow spaces and see where you’re cleaning.

---

What is the mattress tool?

The mattress tool removes dust, dirt, and allergens from mattresses and upholstery.

---

What is the Laser Slim Fluffy™ cleaner head?

A precisely-angled laser makes invisible dust visible on hard floors.

---

What is the High Torque cleaner head with anti-tangle comb?

Dyson DLS™ technology monitors brush bar resistance and adapts power across different floor types, and polycarbonate teeth prevent tangling around the bristles.

---

What does the wall dock do?

Your Dyson vacuum drops into the wall-mounted charging dock, ready for your next clean.

---

What is the wand clip?

The wand clip clips to your vacuum’s wand to hold tools.

---

How do I change power modes?

Your machine has three power modes for different tasks, and you can change power modes quickly using a single button. The three modes are Eco, Auto/Med, and Boost.

---

What is Eco mode?

Eco mode provides maximum run time for longer cleans all around your home.

---

What are Auto and Med modes?

Auto and Med modes provide the optimum balance of power and run time. Attach your cleaner head or Hair screw tool to activate Auto mode, which automatically adapts suction power to dust levels.

---

What is Boost mode?

Boost mode is designed for intensive spot cleaning of ground–in dirt.

---

What does the piezo sensor do?

A piezo sensor continuously sizes and counts dust particles at the inlet.

---

How do I turn the laser on and off?

Turn your laser on or off with the slider switch on your cleaner head.

---

Is the laser safe?

The laser is a Class 1 laser product, making it safe for pets and humans. Avoid looking directly into the beam.

---

What information does the LCD screen display?

The LCD screen shows your particle count information and performance, including the cleaning mode selected, remaining run time, filter maintenance and blockage information.

---

How do I access the settings menu?

To enter the settings menu, press and hold the button until the menu screen appears. Tap to scroll through the options available.

---

How do I change the language on the screen?

1. Press and hold the button until the language list appears, then release the button.
2. Tap the button to scroll through the language list to your preferred language.
3. Press and hold the button until the countdown ends.
4. A green tick will appear on the screen to show your language selection is complete.
5. To cancel your selection, release the button during the countdown.

---

How do I control alert settings?

You can turn the alert motor pulse off, which will stop the motor from pulsing, but run time alert information will continue to be displayed on the LCD screen when your machine needs your attention. Turning off alerts will not turn off the blockage alert pulsing, ensuring you clear any blockages to prevent damage to your machine.

To change the alert settings:

1. Tap to scroll through the settings menu and select the ‘Alerts’ option.
2. Scroll to select on or off.
3. Hold the button until the countdown ends and a tick appears on the screen.
4. To cancel your selection, release the button during the countdown.

---

How do I manage particle count and graph settings?

Select to turn the measuring and counting of particles on and off. Turn off the measuring and counting of particles to stop your machine automatically adjusting suction power and turn off the graph. Automatic adjustment between hard floors and carpets will continue when using the High Torque cleaner head.

---

How do I adjust reactive suction power sensitivity?

Use the selection button to change how sensitive the particle count is, which will change how your machine automatically reacts to the dust particles.

---

How can I get the best performance and life from my battery?

Use Eco or Auto/Med mode.

---

What do the alerts on the screen mean?

The alerts you might see are:

• Filter – the filter isn’t fitted correctly or needs cleaning.
• Blockage – your machine has a blockage that needs removing.

When the battery needs charging, your machine will pulse three times and a low run time icon will appear on the screen. When your battery is empty, a red warning icon will appear on the screen. Low run time will be in amber and red when in Boost mode when Particle count and graph is turned on.

---

How do I charge my machine?

Connect to charger either directly or in the dock. The blue LEDs on either side of the battery will flash during charging. When the battery is fully charged, both LEDs will light for 5 seconds, and the display will show 100%. It’s important to fully charge your new machine before using it for the first time, and after every clean.

---

What are the temperature limitations for operating and charging the machine?

Your machine won’t operate or charge if the ambient temperature is below 5°C (41°F). This is designed to protect both the motor and battery.

---

What should I do if I have additional click-in batteries?

If you have additional click-in batteries, it is recommended that you alternate the batteries to maintain even performance.

---

How do I care for my floors when vacuuming?

1. Check that the underside of the cleaner head or tool is clean and free from any objects that may cause damage.
2. Before vacuuming your flooring, rugs, and carpets, check the manufacturer’s recommended cleaning instructions.
3. Be aware that the brush bar on your machine can damage certain carpet types and floors, and some carpets will fuzz if a rotating brush bar is used when vacuuming. If this happens, it is recommended vacuuming without the motorised floor tool and consulting with your flooring manufacturer.

---

How do I change the click-in battery?

Removing your battery:

1. Push the Battery release button on the handle and slide the battery off your machine.
2. Charge the battery.

Refitting your battery:

1. Align your battery with the handle and slide it in.
2. Push firmly until it clicks into place.

---

How do I empty the bin?

1. Press the red wand release button, on the top of the wand, and pull the wand away from the bin.
2. Hold the machine over the bin, pointing downwards.
3. Firmly push the red bin release button. The bin will slide down, cleaning the shroud as it goes, and the bin base will open. The bin base won’t open if the red bin release button isn’t pushed down all the way.
4. Cover your bin tightly in a dust proof bag while you empty. Remove the bin carefully, seal the bag tightly and dispose.
5. Push the bin base upwards until the bin and bin base click into place.

Empty as soon as the dirt reaches the MAX level – don’t overfill. Using your machine when the dirt is above the MAX line may affect the performance and require more frequent filter washing. Overfilling your bin could result in inaccurate readings on the particle graph.

---

How do I clean the bin?

Removing your bin:

1. Empty it as shown in the ‘Emptying your bin’ section.
2. Press the red button located on the bin runner to release the bin and slide your bin off the runner.

Cleaning and refitting your bin:

1. Only clean your bin with a damp cloth.
2. Make sure that the bin and seals are completely dry before replacing.
3. Insert the spine on to the bin runner.
4. Close your bin by pushing the bin base upwards until the bin and bin base click into place.

---

How do I clear blockages?

1. Disconnect your machine from the charger before looking for blockages.
2. Be careful not to touch the trigger and be aware of sharp objects.
3. Leave your machine to cool down before looking for blockages.
4. Don’t use your machine when looking for blockages as this could cause injury.
5. Make sure any blockages are completely cleared and all parts are fitted before using your machine.
6. If your machine detects a blockage, the motor will pulse and you won’t be able to use your machine until the blockage has been cleared.
7. If you try to use your machine when the motor is pulsing, it will automatically cut out.
8. Refit all parts securely before using your machine.
9. Clearing blockages isn’t covered by your guarantee.

To clear blockages:

1. Remove the bin and check for blockages in the main body of your machine. With the bin removed, check for blockages, paying particular attention to the air inlet, located on the right–hand side of the machine just below the point where the bin joins the main body of the machine.
2. Check the wand for blockages. With the wand removed from the machine, check for blockages at both ends of the wand.
3. Check your cleaner head for blockages, following the instructions to remove the brush bar, where necessary. Turn the cleaner head over to check for obstructions on the brush bar and air inlet.
4. Re–assemble your machine.

---

How do I wash the filter?

Wash your filter at least once a month to maintain optimum suction power.

1. Twist your filter anti-clockwise and pull it away from your machine. The filter is located at the rear of your machine.
2. Before washing your filter, tap it gently over a bin to remove any loose dust and debris.
3. Wash with warm, running tap water – gently rubbing your filter with your fingers to remove the dirt.
4. Place your hand over one end of your filter and fill the filter with warm tap water.
5. Place your hand over the open end of the filter and shake it firmly to remove trapped dirt and debris.
6. Empty the filter and shake firmly to remove excess water. Shake with the filter in both an upward and downward position until there’s no water coming from the filter.
7. Leave your filter to dry for at least 24 hours in a well-ventilated, warm place. Don’t dry your filter in a tumble dryer, microwave or near a naked flame.

Your filter must be completely dry before you put it back into the machine. Your machine could be damaged if used with a damp filter.

---

How do I wash the Laser Slim Fluffy™ brush bar?

To maintain optimum performance, check and wash your brush bar regularly.

1. Make sure your machine is disconnected from the charger and take care not to touch the trigger.
2. Press the cleaner head release button on the end of the wand and place the cleaner head upside down.
3. Push the end cap up fully and pull the brush bar out of the cleaner head. Don’t wash the end cap. The end cap is located at the side of the cleaner head. Push this upwards to unlock the brush bar. The end cap should be attached to the cleaner head at an angle less than 90°, any angle greater than this will not allow the end cap to close.
4. Hold your brush bar under running water and gently rub to remove any lint or dirt.
5. Stand your brush bar upright, with the closed end facing upwards, to dry completely for at least 24 hours. The brush bar has an open end and a closed end.
6. Before replacing, check that your brush bar is completely dry.
7. Reattach the end cap to your brush bar.
8. Slide your brush bar into the cleaner head and push the end cap back down to the closed position.

Don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners.

---

How do I clean the laser lens?

To maintain optimum performance, keep your laser lens clean. Only clean the lens when the cleaner head is not attached to your machine. Use a soft, dry, lint-free cloth to wipe the lens.

---

How do I clear obstructions from the High Torque cleaner head with anti-tangle comb?

Your High Torque cleaner head with anti-tangle comb doesn’t have a washable brush bar. To maintain optimum performance, check your brush bar regularly and clear any obstructions.

1. Make sure your machine is disconnected from the charger and take care not to touch the trigger.
2. Press the cleaner head release button on the end of the wand and place the cleaner head upside down.
3. Use a coin to unlock the end cap.
4. Twist the end cap and remove it from your brush bar. Don’t wash the end cap.
5. Slide your brush bar out of the cleaner head.
6. Clear any debris from your brush bar and check inside the cleaner head and remove any debris or blockages. Remove any hair or fibres that have been wrapped around the brush bar.
7. Push the end cap back on to your brush bar and slide it back into the cleaner head.
8. Turn the end cap into the locked position.

Your cleaner head and brush bar aren’t washable. Wipe over with a damp lint-free cloth and don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners.

---

How do I clean the tools?

Wipe with a damp, lint-free cloth, without touching the connector end. Make sure your tools are completely dry before using, and don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners.

---

How do I clear blockages from the Hair screw tool?

1. Make sure your machine is disconnected from the charger and take care not to touch the trigger.
2. Remove the Hair screw tool from the wand or machine.
3. Push the base plate open.
4. Press the red lever down to release the cleaner head cover. The curved locking lever is located on the back of the tool.
5. Pull the cleaner head cover off the main body of the tool.
6. Pull your brush bar firmly to remove it from the main body.
7. Check and remove any obstructions from all three parts of your Hair screw tool. Remove any hair or fibres that have been wrapped around the brush bar.
8. Put your brush bar back into position and press firmly until it clicks back into position.
9. Align the cleaner head cover with the guide on the main body and push it down until it clicks into position. Check the red locking lever is in the unlocked position.
10. Push the red locking lever up until it clicks into position and push the base plate back into place.

Your Hair screw tool isn’t washable. Wipe over with a damp lint-free cloth and don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners.

---

How do I look after my machine?

1. To always get the best performance from your machine, it’s important to clean it regularly and check for blockages.
2. To get the best performance and life from your battery, use Eco or Auto/Med mode.
3. If your machine is dusty, wipe with a damp lint-free cloth. Don’t use detergents or polishes to clean your machine.
4. Check for blockages in the cleaner head, tools and main body of your machine.
5. Wash your filter regularly and leave to dry completely.

---

Where can I find the serial numbers?

You can find your serial numbers on your machine, battery and charger. Use your serial number to register.