V-ZUG GK37TIMS (01) PDF DOCUMENT

Before using your V-ZUG GK37TIMS for the first time, it’s important to read the operating instructions thoroughly.

This appliance can be used by children aged 8 and above and by persons with reduced physical, sensory or mental capabilities, or lack of experience and/or knowledge, provided they are supervised or have been instructed on the safe use of the appliance and have understood the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be undertaken by children without supervision.

If an appliance is not equipped with a mains cable and a plug or other means for disconnecting from the mains with a contact opening on each pole complying with the conditions of overvoltage category III for full isolation, an isolating device must be incorporated into the permanently installed electrical installation in accordance with the installation regulations.

If the mains cable of this appliance is damaged, it must be replaced by the manufacturer or its Customer Services or a similarly qualified person in order to avoid hazard.

Please adhere to the following safety precautions specific to your V-ZUG GK37TIMS hob:

WARNING: If the surface is cracked or there is damage to the material thickness, the appliance must be switched off and disconnected from the electricity supply in order to avoid a possible electric shock.

WARNING: During use, the appliance and its exposed parts become hot. Please be careful to avoid the exposed parts of the heating elements.

Never use a steam cleaner.

Objects made of metal, e.g. knives, forks, spoons, covers or aluminium foil, should not be put on the hob as they can become hot.

WARNING: Leaving fat or oil unattended on the hob can be dangerous and can lead to fires. NEVER try to extinguish a fire with water. Instead, switch the appliance off and then carefully cover the flames with an object such as a cover or a fire blanket.

WARNING: Never leave objects on the hob as they pose a fire hazard.

The appliance must not be operated with an external time switch or a separate remote control system.

To prevent damage to your V-ZUG GK37TIMS hob, please follow these guidelines:

In the case of thermal failure, switch the solid plate off and allow to cool down completely. Do not put any dishes on it. Do not cool with cold water under any circumstances.

Do not climb onto the appliance.

To avoid damaging the silicon grouting, do not put hot cookware on the frame.

Do not cut or prepare food on the surface or drop hard objects onto it. Do not drag cookware across the surface.

Make sure that no sugary foods or juices end up on the hot cooking zones. This can damage the surface. If sugary foods or juices do end up on the hot cooking zones, remove these immediately with a glass ceramic hob scraper (while the hob is still hot).

Do not leave the appliance unattended during operation.

Pots with pure copper or aluminium bases should not be used for cooking as they leave behind traces that can be difficult to clean. If the traces are not removed immediately after cooking with a suitable cleaning agent, they can be permanently burned on and therefore permanently ruin the visual appearance of the appliance.

Sliding pots and cookware across the glass ceramic causes scratches. You can largely avoid these by lifting pots and cookware when putting them into place.

The hob is an item for daily use: signs of usage such as scratches or visible material abrasion from pots or cookware are normal. Intensive use leads to more distinctive signs of usage. In such cases, the appliance continues to function perfectly and a complaint is not justified. Safety is always guaranteed.

There is no such thing as completely scratch-proof glass; scratches can even develop on sapphire glass, which is used in watches. The glass ceramic used is of the best quality available on the market.

The identification plate (1) and the connection plate (2) are located on the underside of the hob. A second identification plate is supplied and should be affixed in the fitted unit underneath the hob.

It is important to note down the serial number (FN) from the identification plate, as it is required for identifying the appliance for customer service.

Here is a guide to the buttons and display elements on your V-ZUG GK37TIMS hob:

Buttons:

Power icon (circle with a vertical line): Device ON/OFF

0 . . . . . . . . P: Slider (to set the power level)

P: PowerPlus

II: Pause cooking ON/OFF and restore function

Hand icon: Wipe protection ON/OFF

8: Select the cooking zone

88: Operating time/timer

Displays:

1: Power level of the cooking zone

2: Selection point: cooking zone selected

3: Operating time activated

4: Cooking zone indicator light for the operating time

5: Operating time/timer

6: Pause activated/restoration of saved setting possible

7: Wipe protection activated

Every cooking zone on your V-ZUG GK37TIMS is equipped with pan detection. This feature recognises cookware with a magnetisable base that is suitable for use with induction hobs.

If the cookware is removed during operation or unsuitable cookware is used, the selected power level flashes alternately with the symbol ‘U’.

If there is no cookware placed on the cooking zone during the pan detection time of 10 minutes:

The cooking zone switches off automatically.

The display changes from ‘U’ to ‘0’.

The appliance switches off after 10 seconds if no other cooking zone is switched on.

Only cookware with a full magnetic base is suitable for use with the V-ZUG GK37TIMS induction hob. You can check this in the following ways:

A magnet sticks anywhere on the base of the cookware.

On the hob, the power level set illuminates and the ‘U’ symbol does not alternate with the power level.

Do not heat any unsuitable cookware using aids such as metal rings and the like, as this can damage the hob.

For maximum energy efficiency and even heat distribution on your V-ZUG GK37TIMS, please note the following:

The base of the cookware must be clean, dry and smooth.

Centre the cookware in the middle of the cooking zone.

Use a well-fitting lid.

Match the diameter of the cookware to the quantity of food to be cooked.

Yes, when using coated cookware on your V-ZUG GK37TIMS, please follow these instructions:

Coated cookware when empty may never be heated at a higher power level than 7. The coating may otherwise become overheated and damaged.

For frying, do not use a higher power level than 9.

Never use PowerPlus with coated frying pans.

The flexible cooking feature is applicable for V-ZUG GK37TIMS models. For flexible cooking, there are no marked cooking zones. Pots of different sizes can be placed on every zone. However, for pan detection, the circle symbol must be covered.

If both circles are covered by a large pot, both heating areas can be operated together with the bridge function. For even frying, the pan must be centred on the circle.

To switch the appliance on: Depress the ON/OFF button (power icon) for 1 second. ‘0’ flashes in all the power level displays. If no other entry is made, the appliance switches off again after about 10 seconds for safety reasons.

To switch the appliance off: Touch the ON/OFF button (power icon).

Follow these steps to select a cooking zone and set the power level:

1. Press the ‘8’ button of the required cooking zone. ‘0’ flashes in the corresponding display of the power level, and the selection point for this cooking zone is illuminated.

2. Touch the slider or swipe it to set the desired power level.

Settings for a cooking zone can only be changed when the corresponding selection point is illuminated. As soon as the selection point goes out, the cooking zone must be selected again.

The V-ZUG GK37TIMS offers various power levels for different cooking methods:

1. Press the ‘8’ button of the required cooking zone. The selection point of this cooking zone will be illuminated.

2. Touch power level ‘0’ on the slider.

If no other entry is made and the other cooking zones are switched off, the appliance switches off after 10 seconds.

Keep warm setting (L): The keep warm setting ‘L’ keeps ready-cooked foods warm at approx. 65 °C. It can be found between power levels ‘0’ and ‘1’ on the slider.

Melting function: With the melting function, butter, chocolate or honey, for instance, can be gently melted at 40 °C.

To switch on: Hold power level ‘L’ on the slider depressed for 2 seconds. Two horizontal bars illuminate in the power level display.

To switch off: Use the slider to set any other power level.

Simmer function: With the simmer function, sausages, dumplings and stuffed pasta, for instance, can be cooked below boiling point at about 94 °C.

To switch on: Press the level ‘L’ on the slider for 4 seconds. Three cross pieces illuminate in the power level display.

To switch off: Set any power level using the slider.

All cooking zones on your V-ZUG GK37TIMS are equipped with a PowerPlus booster. When PowerPlus is switched on, the selected cooking zone works at extra high power for 10 minutes, which is useful for heating a large quantity of water quickly.

Switching PowerPlus on:

1. Press the ‘8’ button of the required cooking zone.

2. Touch the slider past ‘9’ to ‘P’ twice. ‘P’ is illuminated in the display.

After 10 minutes, it automatically reverts to power level 9.

If the cookware is removed, PowerPlus is interrupted. PowerPlus continues as soon as the cookware is placed back on the cooking zone.

Ending PowerPlus before time:

1. Press the ‘8’ button of the required cooking zone.

2. Touch the required power level on the slider.

For the V-ZUG GK37TIMS model, PowerPlus cannot be used in cooking zones 1 and 2 at the same time. If PowerPlus is activated for both cooking zones, the power of the cooking zone that was initially set reduces. Cooking zone 3 can be operated with PowerPlus independently of 1 and 2. The maximum available power levels are as follows:

If the power level is raised above the values specified above, PowerPlus switches off.

Do not leave the hob unattended when using the automatic boost. Risk of boiling over, burning on and igniting!

All cooking zones are equipped with a selectable automatic boost. With this function, a cooking zone works at power level 9 for a certain length of time and then automatically switches back to the power level you set. The duration of the boost depends on the selected power level:

Switching the automatic boost on:

1. Press the ‘8’ button of the required cooking zone.

2. Press the required power level on the slider for 3 seconds. As long as the automatic boost is active, ‘A’ and the power level are illuminated alternately in the display.

After the boost time has ended, the heat output is reduced to the selected power level again.

Switching the automatic boost off before time:

1. Press the ‘8’ button of the required cooking zone.

2. Set a lower power level using the slider.

Setting the operating time (1-99 min):

1. Set the required cooking zone.

2. Press the ‘8’ button of the required cooking zone.

3. Press the ’88’ button. ’00’ appears in the display, and the second digit flashes.

4. Set the second digit of the operating time using the slider.

5. Press the ’88’ button. The first digit flashes.

6. Set the first digit of the operating time using the slider.

7. Press the ’88’ button. The operating time starts.

Changing the operating time:

1. Press the ‘8’ button of the required cooking zone. The remaining time is displayed.

2. Press the ’88’ button.

3. Change the second digit using the slider.

4. Press the ’88’ button.

5. Change the first digit using the slider.

6. Press the ’88’ button. The changed operating time starts.

Switching the operating time off before time:

Follow the steps for changing the operating time but set both digits to ‘0’.

The timer functions like an egg timer (1-99 min.) and can only be set when a cooking zone is in operation.

Setting the timer:

1. Switch on the appliance.

2. Press the ’88’ button. ’00’ appears, and the second digit flashes.

3. Set the second digit of the timer using the slider.

4. Press the ’88’ button. The first digit flashes.

5. Set the first digit of the timer using the slider.

6. Press the ’88’ button. The timer starts.

To change the timer, repeat the same steps. To switch the timer off before time, press the ’88’ button and set both digits to ‘0’ using the slider.

Switching the childproof lock on:

1. Switch the appliance on. Ensure all cooking zones are switched off.

2. Touch the ‘II’ and ‘hand’ buttons at the same time. An acoustic signal is emitted.

3. Touch the ‘II’ button again. An acoustic signal is emitted. The childproof lock is now switched on, and a lock symbol illuminates in all power level displays for 10 seconds.

Operating the appliance with the childproof lock activated:

1. Switch the appliance on.

2. Touch the ‘II’ and ‘hand’ buttons at the same time. An acoustic signal is emitted, and the childproof lock is overridden. The appliance can now be used as normal. The childproof lock is automatically activated again after switching off the hob.

Switching the childproof lock off permanently:

1. Switch on the appliance. No cooking zone must be in operation.

2. Touch the ‘II’ and ‘hand’ buttons at the same time. An acoustic signal is emitted.

3. Press the ‘hand’ button again. A double acoustic signal is emitted. On all power level displays, ‘0’ flashes for 10 seconds. The childproof lock is now switched off.

Restore function: If the appliance was switched off accidentally with the ON/OFF button, the settings can be restored within 6 seconds. Switch the appliance on, and the illuminated point for the ‘II’ button will flash. Press the ‘II’ button to restore the previous settings.

Pause cooking: Press the ‘II’ button. The power level of all active cooking zones is temporarily reduced to ‘1’ for up to 10 minutes. The indicator light for the ‘II’ button illuminates. The operating time is interrupted, but the timer continues to run. All buttons except ON/OFF, ‘II’, and ‘hand’ are inactive. Press the ‘II’ button again to resume cooking with the previous settings. If not resumed within 10 minutes, the appliance switches off completely.

Wipe protection: Press the ‘hand’ button. This function prevents the power level from being changed accidentally, for instance when wiping the control panel with a cloth. The indicator light for the ‘hand’ button illuminates. Wipe protection is switched off by pressing the ‘hand’ button again or automatically after 30 seconds. You can press the ON/OFF button to switch the appliance off at any time.

Preferably, do not clean the appliance until it is cold to avoid a burn hazard. Clean the hob after every use to prevent food residues from burning on.

Do not clean the glass ceramic surface with scouring cleaning agents, all-purpose scouring pads, steel wool, etc. This can damage the surface.

For cleaning everyday dirt, just use a soft cloth or sponge with water and a suitable cleaning agent. Follow the manufacturer’s advice with regard to cleaning agents.

Remove encrusted dirt, e.g. from milk that has boiled over, with a glass ceramic hob scraper while the hob is still warm. Follow the manufacturer’s advice for the scraper.

Remove sugary foods, such as marmalade, which have boiled over with a glass ceramic hob scraper while the hob is still warm. Otherwise, this could damage the glass ceramic surface.

Remove melted plastic with a glass ceramic hob scraper while the hob is still warm to avoid damaging the surface.

Remove limescale stains using a small amount of lime-dissolving solution, e.g. vinegar or lemon juice, when the hob has cooled down. Then clean again with a damp cloth.

If your hob is not working, check the following possible causes:

Possible Cause: The fuse or circuit breaker for electrical installations in the home is defective.

Solution: Change the fuse or reset the circuit breaker.

Possible Cause: The fuse or circuit breaker keeps blowing.

Solution: Call Customer Services.

Possible Cause: An interruption in the power supply.

Solution: Check the power supply.

This indicates a problem with the cookware.

Possible Cause: Cookware is not suitable for use with induction hobs.

Solution: Use suitable magnetic cookware as described in the “Cookware” section.

Possible Cause: Cookware is too small for the cooking zone selected.

Solution: Ensure cookware corresponds to the size of the cooking zone.

Possible Cause: The childproof lock is activated.

Solution: For operating the appliance with the childproof lock activated, see the “Operating the appliance” section. To deactivate it permanently, switch the childproof lock off.

This usually indicates something is on the control panel.

Possible Causes:

A button or a slider was touched for longer than 10 seconds.

An object (e.g. pan, dish) is on the control panel.

Food boiled over onto the control panel.

Solution: Remove the object or food that has boiled over. The appliance can be used again as normal.

Possible Cause: The automatic safety shut-off was triggered. If a cooking zone has been running for a long time without any settings being changed, the appliance switches the cooking zone off automatically. The time depends on the power level set.

Solution: Switch the cooking zone back on again if required.

Possible Cause: The excess temperature protection of a cooking zone was triggered.

Solution: Allow the cooking zone to cool down. You can continue cooking on a different cooking zone. Also, check your cookware to ensure it is suitable.

Possible Cause: An interruption in the power supply.

Solution: Press any button to quit the error message. The appliance can be used again as normal.

This indicates an issue with ventilation.

Possible Cause: An object, e.g. paper, underneath the hob is affecting the air intake.

Solution: Remove any objects in the drawer underneath the hob. Press any button to cancel the error message. After 10 minutes the appliance can be used again as normal.

Possible Cause: Ventilation is defective.

Solution: Note down the error number and the serial number (FN) of the appliance from the identification plate. Call Customer Services.

Possible Cause: An internal error has occurred.

Solution: Note down the error number. Note down the serial number (FN) of the appliance from the identification plate. Call Customer Services.