TOYOTA 86 2020 (01) PDF MANUAL

The keys provided with your TOYOTA 86 2020 depend on the system installed:

For vehicles without a smart key system:

• Master keys: Used for all functions, including operating the wireless remote control.

• Valet key: A key with limited function, typically for parking attendants.

• Key number plate: Contains a number that allows a new key to be made if you lose your keys.

For vehicles with a smart key system:

• Electronic keys: Operate the smart key system and the wireless remote control function.

• Mechanical keys: Housed inside the electronic keys, used when the electronic key battery is depleted.

• Key number plate: Contains a number that allows a new mechanical key to be made if one is lost.

To take out the mechanical key from the electronic key fob of your TOYOTA 86 2020, slide the release lever and pull the key out.

After using the mechanical key, store it back in the electronic key. It is important to carry the mechanical key together with the electronic key, as you will need it if the electronic key’s battery is depleted or the entry function does not operate properly.

The smart key system on your TOYOTA 86 2020 allows you to perform operations simply by carrying the electronic key on your person.

Unlocking and Locking the Doors:

• To unlock, grip the driver’s or passenger’s door handle. Make sure to touch the sensor on the back of the handle. Gripping the driver’s handle unlocks the driver’s door; gripping the passenger handle unlocks all doors.

• To lock, touch the lock sensor (the indentation on the side of the door handle). A buzzer will sound once, and the emergency flashers will flash once to confirm.

Unlocking the Trunk:

• Press the button on the trunk to unlock it.

Starting the Engine:

• With the electronic key inside the vehicle, you can start the engine using the “ENGINE START STOP” switch.

The wireless remote control for your TOYOTA 86 2020 has the following functions:

For vehicles without a smart key system:

1. Locks both side doors.

2. Unlocks both side doors. Pressing once unlocks the driver’s door. Pressing again within 3 seconds unlocks the other door.

3. Sounds the alarm (panic mode): Press and hold.

4. Unlocks the trunk: Press and hold.

For vehicles with a smart key system:

1. Locks both side doors.

2. Unlocks both side doors. Pressing once unlocks the driver’s door. Pressing again within 3 seconds unlocks the other door.

3. Unlocks the trunk: Press and hold.

4. Sounds the alarm (panic mode): Press and hold.

You can lock and unlock the doors of your TOYOTA 86 2020 from inside the vehicle using the following methods:

Door Lock Switch:

• Located on the driver’s door panel.

• Press one side of the switch to lock both doors.

• Press the other side of the switch to unlock both doors.

Inside Lock Button:

• Located on each door.

• Push the button in to lock the door.

• Pull the button out to unlock the door.

You can open the trunk of your TOYOTA 86 2020 using several methods:

From inside the vehicle:

• Press and hold the trunk opener switch located on the instrument panel to release the trunk lid.

From outside the vehicle:

• Key (vehicles without a smart key system): Turn the master key clockwise in the trunk lock to release the lid.

• Entry function (vehicles with a smart key system): With the electronic key on your person, press the button on the trunk.

• Wireless remote control: Press and hold the trunk button on the key fob.

There is also an internal trunk release lever located on the inside of the trunk lid, which glows in the dark for emergency use.

To adjust the front seats in your TOYOTA 86 2020, use the following controls:

1. Seat position adjustment lever: Located under the front of the seat. Pull the lever up to slide the seat forward or backward.

2. Seatback angle adjustment lever: Located on the side of the seat. Pull the lever up to adjust the angle of the seatback.

3. Vertical height adjustment lever (driver’s side only): Located on the side of the seat. Pump the lever up or down to raise or lower the seat cushion.

4. Seatback fold strap: Pull this strap to fold the seatback forward to allow access to the rear seats.

After adjusting the seat, make sure it is locked in position by trying to move it forward and backward.

To fold down the rear seatbacks in your TOYOTA 86 2020 for extra cargo space:

1. Open the trunk.

2. Pull the seatback lock release straps located in the trunk for the seatback you wish to fold down.

3. The seatback will release and can be pushed to fold down.

To return a seatback to its original position, lift it up until it locks securely in place. Push and pull on the top of the seatback to ensure it is locked.

Properly adjusting the head restraints is crucial for safety in your TOYOTA 86 2020.

Adjustment:

• Up: Pull the head restraint upwards.

• Down: Push the head restraint down while pressing the lock release button.

Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears.

Removing and Installing:

• To remove: Pull the head restraint up while pressing the lock release button.

• To install: Align the head restraint with the installation holes and push it down to the lock position. Press and hold the lock release button if needed when lowering.

For maximum protection, all occupants must wear their seat belts correctly in the TOYOTA 86 2020:

• Sit up straight and well back in the seat.

• Position the lap belt as low as possible over the hips, not the waist.

• Extend the shoulder belt so that it comes fully over the shoulder, but does not come into contact with the neck or slide off the shoulder.

• Ensure the seat belt is not twisted.

To fasten the belt, push the plate into the buckle until a click is heard. To release, press the release button on the buckle.

To adjust the steering wheel in your TOYOTA 86 2020 to a comfortable position, follow these steps:

1. Hold the steering wheel and push the lever located under the steering column down.

2. Adjust to the ideal position by moving the steering wheel horizontally (telescopic adjustment) and vertically (tilt adjustment).

3. After adjustment, pull the lever up firmly to secure the steering wheel.

Warning: Do not adjust the steering wheel while driving. After adjusting, ensure it is securely locked by trying to move it up, down, forward, and back.

The power windows in your TOYOTA 86 2020 are operated by switches on the driver’s door.

Operating the driver’s window:

• Closing: Pull the switch up.

• One-touch closing: Pull the switch up fully and release.

• Opening: Push the switch down.

• One-touch opening: Push the switch down fully and release.

Pushing the switch in the opposite direction will stop the window partway.

Window Lock Switch:

• Press the window lock switch down to lock the passenger window. This prevents children from accidentally opening or closing the passenger window.

Follow these steps to safely refuel your TOYOTA 86 2020:

Before Refueling:

• Turn the engine switch off.

• Ensure all doors and windows are closed.

• Confirm the correct fuel type (Unleaded gasoline, octane rating 93 [98 RON] or higher).

Opening the Fuel Tank Cap:

1. Pull up the fuel filler door opener located on the floor next to the driver’s seat.

2. Turn the fuel tank cap slowly to open it. A hissing sound may be heard as pressure is released.

3. Hang the fuel tank cap on the back of the fuel filler door while refueling.

Closing the Fuel Tank Cap:

• After refueling, turn the fuel tank cap clockwise until you hear a click. Once released, it will turn slightly in the opposite direction.

The alarm system on your TOYOTA 86 2020 sounds an alarm and flashes the lights when forcible entry is detected.

Setting the Alarm System:

Close all doors and the trunk, then lock the doors using the entry function, wireless remote control, or by locking from the outside without a key. The system will be set automatically after about 30 seconds, and the indicator light will change from solid to flashing.

Deactivating or Stopping the Alarm:

Perform one of the following:

• Unlock the doors using the entry function or wireless remote control.

• Turn the “ENGINE START STOP” switch to ACCESSORY or IGNITION ON mode, or start the engine.

Activating/Deactivating the Alarm System (Customization):

1. Check that both side doors and the trunk are closed.

2. Turn the “ENGINE START STOP” switch to IGNITION ON mode.

3. Open the driver’s door while pressing and holding the unlock side of the door lock switch, and continue to press the lock side for approximately 10 seconds. The system will change between activated (one horn sound) and deactivated (two horn sounds).

Driving with a good posture enhances safety and control in your TOYOTA 86 2020. Follow these steps:

1. Sit upright and well back in the seat.

2. Adjust the seat forward or backward to ensure you can easily depress the pedals to the full extent required.

3. Adjust the seatback so that the controls are easily operable.

4. Adjust the tilt and telescopic positions of the steering wheel to allow easy operation and ensure the airbag is facing your chest.

5. Lock the head restraint in place with the center of the head restraint closest to the top of your ears.

6. Wear the seat belt correctly.

The SRS (Supplemental Restraint System) airbags in your TOYOTA 86 2020 work with seat belts to help reduce the risk of serious injury in certain severe impacts. The system consists of six airbags:

• Driver’s and front passenger’s frontal airbags

• Driver’s and front passenger’s side airbags

• Curtain shield airbags (for driver, front passenger, and rear passengers)

Important Safety Precautions:

• Always wear your seat belt. Airbags are a supplement to, not a replacement for, seat belts.

• The driver should sit upright, well back in the seat, and as far from the steering wheel as is practical.

• The front passenger should move their seat as far back as possible and sit upright.

• Do not place any objects on or near the airbag covers.

• Children aged 12 and under should be properly restrained in the rear seat, which is safer than the front seat.

• NEVER install a rear-facing child seat in the front passenger seat.

Firmly secure child restraints to the rear seats of your TOYOTA 86 2020 using either the LATCH anchors or a seat belt. Always attach the top tether strap when installing a child restraint.

Installation with LATCH System:

The vehicle is equipped with LATCH (Lower Anchors and Tethers for Children) anchors for both rear seats.

1. Pull the seat cover to expose the LATCH anchors.

2. Latch the hooks or buckles of the child restraint’s lower straps onto the LATCH anchors.

3. Attach the top tether strap to the anchor bracket on the rear parcel shelf and tighten it.

Installation with a Seat Belt:

1. Place the child restraint system on the rear seat.

2. Run the seat belt through the child restraint system and insert the plate into the buckle. Ensure the belt is not twisted.

3. Fully extend the shoulder belt and allow it to retract to engage the lock mode (ALR). In lock mode, the belt cannot be extended.

4. Push the child restraint down into the seat while allowing the shoulder belt to retract until the restraint is secure.

5. If the restraint has a top tether strap, latch it onto the top tether strap anchor and tighten.

Starting the Engine:

• Automatic Transmission: With the brake pedal depressed, shift the shift lever to D.

• Manual Transmission: While depressing the clutch pedal, shift the shift lever to 1.

Driving:

• Release the parking brake.

• Gradually release the brake pedal (or clutch pedal) and gently depress the accelerator pedal to accelerate.

Stopping:

• Depress the brake pedal (and clutch pedal for manual transmission).

• If necessary, set the parking brake.

Parking:

1. With the vehicle stopped, apply the parking brake.

2. Shift the shift lever to P (automatic) or N (manual).

3. Turn the engine off.

4. Lock the doors.

The procedure for starting the engine of your TOYOTA 86 2020 depends on your vehicle’s systems.

For vehicles with a smart key system:

1. Ensure the parking brake is set.

2. Confirm the shift lever is in P (automatic) or N (manual).

3. Firmly depress the brake pedal (automatic) or clutch pedal (manual).

4. Press the “ENGINE START STOP” switch. The engine will crank until it starts.

For vehicles without a smart key system:

1. Check that the parking brake is set and the shift lever is in P (automatic) or N (manual).

2. Firmly depress the brake pedal (automatic) or clutch pedal (manual).

3. Turn the engine switch (key) to the “START” position to start the engine.

The automatic transmission in your TOYOTA 86 2020 can be operated in several modes.

Shift Position Uses:

• P: Park. Locks the transmission.

• R: Reverse.

• N: Neutral.

• D: Drive. For normal driving, the system will select a suitable gear automatically.

• M: Manual Mode. Allows you to select gears manually using the shift lever or paddle shifters.

Selecting a Driving Mode:

Press the driving pattern selector switch to cycle through modes:

• Normal mode: For regular driving.

• Sport mode: The “SPORT” indicator comes on. This mode uses lower gears and changes gears at higher engine speeds for sportier driving.

• Snow mode: The “SNOW” indicator comes on. Use for accelerating and driving on slippery surfaces like snow.

Manual Mode Driving:

To enter manual mode, move the shift lever to the M position. You can then change gears using the shift lever (+ for upshift, – for downshift) or the paddle shifters on the steering wheel.

Cruise control allows you to maintain a set speed without depressing the accelerator pedal.

Setting the Vehicle Speed:

1. Press the “ON-OFF” button on the cruise control switch to activate the system. The cruise control indicator will come on.

2. Accelerate or decelerate to your desired speed (must be above approx. 25 mph or 40 km/h).

3. Push the lever down to set the speed. The “SET” indicator will come on. The vehicle speed at the moment the lever is released becomes the set speed.

Adjusting the Set Speed:

• To increase speed, push the lever up.

• To decrease speed, push the lever down.

Canceling and Resuming:

• To cancel, pull the lever toward you or depress the brake pedal (or clutch pedal on manual transmission models).

• To resume the previously set speed, push the lever up (vehicle speed must be above approx. 20 mph or 30 km/h).

Your TOYOTA 86 2020 is equipped with several systems to enhance driving safety and performance:

• ABS (Anti-lock Brake System): Helps to prevent wheel lock when braking suddenly or on a slippery surface.

• Brake assist: Generates increased braking force when the system detects a panic stop.

• VSC (Vehicle Stability Control): Helps the driver control skidding when swerving suddenly or turning on slippery roads.

• TRAC (Traction Control): Helps maintain drive power and prevents the drive wheels from spinning when starting or accelerating on slippery roads.

• Hill-start assist control: Helps maintain braking force to assist starting off on an incline.

• EPS (Electric Power Steering): Uses an electric motor to reduce the effort needed to turn the steering wheel.

Exterior Cleaning:

• Working from top to bottom, liberally apply water to the vehicle body, wheel wells, and underside to remove dirt and dust.

• Wash the vehicle body using a sponge or soft cloth with car wash soap.

• Rinse thoroughly with water and wipe dry.

• Wax the vehicle when the waterproof coating deteriorates (when water does not bead on a clean surface).

Interior Cleaning:

• General Surfaces: Remove dirt and dust with a vacuum cleaner. Wipe dirty surfaces with a cloth dampened with lukewarm water. For stubborn dirt, use a cloth dampened with neutral detergent diluted to approximately 1%.

• Leather Areas: After vacuuming, wipe with a soft cloth dampened with a diluted neutral wool detergent (approx. 5%). Wring out excess water and wipe off all traces of detergent. Allow to dry in a shaded, ventilated area.

• Synthetic Leather: Clean with a vacuum and then a soft cloth dampened with neutral detergent diluted to approximately 1%.

• Seat Belts: Clean with mild soap and lukewarm water using a cloth or sponge.

You can perform several basic maintenance checks on your TOYOTA 86 2020. Always ensure the engine is off and cool before starting.

• Engine Oil: With the engine warm and turned off for at least five minutes, park on level ground. Pull out the dipstick, wipe it clean, reinsert it fully, then pull it out again to check the level. It should be between the low and full marks.

• Engine Coolant: When the engine is cold, check the coolant level in the reservoir. It should be between the “FULL” and “LOW” lines.

• Brake Fluid: The brake fluid level should be between the “MAX” and “MIN” lines on the reservoir tank.

• Battery: Check that the battery terminals are not corroded and that connections are tight.

• Washer Fluid: If the washer fluid level is low, add washer fluid.

• Tires: Check for wear and check the inflation pressure when the tires are cold.

If an electrical component is not working, a fuse may have blown. Follow these steps to check and replace it:

1. Turn the engine switch off.

2. Open the fuse box cover. There is one in the engine compartment and one in the instrument panel inside the cabin.

3. Refer to the fuse layout diagram on the fuse box lid to identify the fuse for the malfunctioning component.

4. Remove the fuse using the pull-out tool provided in the engine compartment fuse box.

5. Check if the fuse is blown (the wire inside will be broken).

6. If it is blown, replace it with a new fuse of the same amperage rating. The amperage rating can be found on the fuse box lid.

If the new fuse blows again, have the vehicle inspected by your Toyota dealer.

If a warning light comes on, take the appropriate action based on the light.

Stop the vehicle immediately if these lights come on:

• Brake system warning light: Indicates low brake fluid or a malfunction. The vehicle may be dangerous to drive.

• Charging system warning light: Indicates a malfunction in the charging system.

• Low engine oil pressure warning light: Indicates engine oil pressure is too low.

• High engine coolant temperature warning light: Indicates the engine is almost overheating.

Have the vehicle inspected immediately if these lights come on:

• Malfunction indicator lamp (Check Engine Light): Indicates a malfunction in the engine or transmission control systems.

• SRS warning light: Indicates a malfunction in the airbag or seat belt pretensioner system.

• ABS warning light: Indicates a malfunction in the ABS or brake assist system.

• Electric power steering warning light: Indicates a malfunction in the EPS system.

Follow correction procedures for these lights:

• Low fuel level warning light: Refuel the vehicle.

• Seat belt reminder light: Fasten the seat belt.

• Tire pressure warning light: Check and adjust tire pressure.

Your TOYOTA 86 2020 is equipped with a compact spare tire, jack, and tools to replace a flat tire.

Before Changing the Tire:

1. Stop the vehicle in a safe place on a hard, flat surface.

2. Set the parking brake firmly.

3. Shift to P (automatic) or R (manual).

4. Turn off the engine and turn on the emergency flashers.

Replacing the Flat Tire:

1. Chock the tire diagonally opposite the flat tire.

2. Slightly loosen the wheel nuts on the flat tire (one turn).

3. Position the jack at the correct jack point and raise the vehicle until the tire is slightly off the ground.

4. Remove the wheel nuts and the flat tire.

5. Install the spare tire and loosely tighten the wheel nuts by hand.

6. Lower the vehicle.

7. Firmly tighten each wheel nut two or three times in a star pattern to the specified torque: 89 ft•lbf (120 N•m).

8. Stow the flat tire, jack, and tools.

Have the flat tire repaired or replaced as soon as possible. The compact spare tire is for temporary use only.

If the engine will not start, consider the following causes:

If the starter motor operates normally, but the engine does not start:

• You may be out of fuel. Refuel the vehicle.

• The engine may be flooded. Try to restart the engine following the correct starting procedures.

• There may be a malfunction in the engine immobilizer system.

If the starter motor turns over slowly, lights are dim, or the horn is weak:

• The battery may be discharged. You may need to jump-start the vehicle.

• Battery terminal connections may be loose or corroded.

If the starter motor does not turn over at all:

• One or both of the battery terminals may be disconnected.

• The battery may be discharged.

• For vehicles with a smart key system, there may be a malfunction in the steering lock system or the engine starting system (e.g., blown fuse).

If you have a set of jumper cables and a second vehicle with a 12-volt battery, you can jump-start your TOYOTA 86 2020.

1. Connect the jumper cables in the following order:

a. Connect one red clamp to the positive (+) terminal on your vehicle’s battery.

b. Connect the other red clamp to the positive (+) terminal on the second vehicle’s battery.

c. Connect one black clamp to the negative (-) terminal on the second vehicle’s battery.

d. Connect the final black clamp to a solid, unpainted metal ground point on your vehicle, away from the battery.

2. Start the engine of the second vehicle. Increase the engine speed slightly and maintain it for about 5 minutes to recharge your battery.

3. Start your vehicle’s engine.

4. Once your vehicle’s engine has started, remove the jumper cables in the exact reverse order in which they were connected.

If your vehicle’s engine coolant temperature gauge enters the red zone, the temperature warning light flashes, or you see steam coming from under the hood, your vehicle is overheating. Follow these steps:

1. Stop the vehicle in a safe place and turn off the air conditioning system, then stop the engine.

2. If you see steam, wait until it subsides before carefully lifting the hood. If you do not see steam, carefully lift the hood.

3. After the engine has cooled down sufficiently, inspect the hoses and radiator for any leaks.

4. Check the coolant level in the reservoir. If it is low, add coolant after the engine has cooled completely. In an emergency, water can be used.

5. Start the engine and turn the A/C on to check that the cooling fans are operating. If the fans are not operating, stop the engine immediately. If they are operating, have the vehicle inspected at the nearest Toyota dealer.

Warning: Do not remove the radiator cap when the engine is hot.

Here is some key information for your TOYOTA 86 2020 when visiting a gas station: