SONY MDR-ZX330BT (02) PDF DOCUMENT

Connect the SONY MDR-ZX330BT to a booted computer using the supplied micro-USB cable. When the unit and the computer are connected, charging starts and the indicator (red) lights up. Charging is completed in about 4 hours at most, and the indicator (red) will go off automatically.

Notes:

• Use the micro-USB cable supplied. You may not be able to charge the unit with other cables.

• Charging will not be completed properly if the computer enters into hibernation or standby mode while connected to the unit. If this happens, change the settings of the computer and charge the unit again.

By touching the SONY MDR-ZX330BT with a compatible smartphone, the unit turns on automatically and proceeds to pair and connect via BLUETOOTH.

1. Set the NFC function of the smartphone to on. For details, refer to the operating instructions supplied with the smartphone.

• If your smartphone OS is Android 2.3.3 or later, and less than Android 4.1 (excluding Android 3.x): proceed to step 2.

• If your smartphone OS is Android 4.1 or later: proceed to step 4.

2. For older Android versions, download and install the app “NFC Easy Connect.” “NFC Easy Connect” is a free Android app you can download from Google Play™.

3. Start the app “NFC Easy Connect” on the smartphone. One-touch connection is possible only when the app screen is displayed on the smartphone.

4. Touch the SONY MDR-ZX330BT with the smartphone. Unlock the screen of the smartphone beforehand. Touch the smartphone on the N-marked part of the unit. Keep touching the unit with the smartphone until the smartphone reacts. Follow the on-screen instructions to complete the pairing and connection.

To disconnect, touch the smartphone again.

To connect the unit with the paired smartphone, perform step 4. (When you are using the app “NFC Easy Connect,” perform steps 3 and 4.)

NFC-compatible smartphones with Android™ 2.3.3 or later installed (excluding Android 3.x) are compatible.

1. Place the BLUETOOTH device within 1 m of this unit.

2. Enter pairing mode on this unit. Press and hold the POWER button for about 7 seconds. Make sure that the indicator flashes blue and red alternately after you release the button.

3. Perform the pairing procedure on the BLUETOOTH device to detect this unit. When the list of detected devices appears on the display of the BLUETOOTH device, select “MDR-ZX330BT.” If passkey input is required on the display of the BLUETOOTH device, input “0000.”

4. Make the BLUETOOTH connection from the BLUETOOTH device.

1. Turn on the unit. Press and hold the POWER button for about 2 seconds while this unit is turned off. Make sure that the indicator flashes blue after you release the button.

2. Make the BLUETOOTH connection from the BLUETOOTH device.

1. Put on the headset. The left unit has a tactile dot.

2. Start playback on the BLUETOOTH device.

3. Operate the headset controls as follows:

Play/pause: Press ►II.

Stop: Hold ►II down.

Next/previous: Press ►►I/I◄◄.

Fast forward/fast reverse: Hold ►►I/I◄◄ down.

Volume: Press VOL +/VOL -.

Notes:

• The available functions may vary depending on the BLUETOOTH device. When you operate the buttons, they may operate differently or may not work at all.

• The sound quality is set to the standard mode (SBC high quality mode) before shipment. When you connect a BLUETOOTH device compatible with AAC, you can change the setting as described in the Help Guide to enjoy music playback at a higher level of sound quality.

To make a call, operate your mobile phone.

When an incoming call arrives, press the 📞 button on the unit to receive it. This works even when you are listening to music. The music playback pauses during a call and resumes automatically when the call is over.

The microphone is omni directional. You do not need to worry about the position of the microphone when you speak.

To terminate a call, press the 📞 button on the unit again.

Notes:

• Music playback may not resume automatically with some BLUETOOTH devices.

• Volume for a call and listening to music can be adjusted independently.

1. Terminate the BLUETOOTH connection by touching the smartphone (if using NFC) or operating the BLUETOOTH device.

2. Press and hold the POWER button for about 2 seconds. The indicator (blue) goes off and the unit turns off.