PREMIUM PCH797DR (01) PDF DOCUMENT

The technical characteristics for the PREMIUM PCH797DR cooker hood are as follows:

Total power: 154W

Three speed motor: 150W

Lights: 2x2W LED lights

Voltage: 110~120 V

Frequency: 60HZ

Filter: 4-layer filter

Control: 3-speed Highly-sensitive touch video switch

Before installing your PREMIUM PCH797DR, please adhere to the following requirements for optimal performance and safety:

1. Do not install the cooker hood where there are many doors or windows, as this can affect the exhaust efficiency due to air convection.

2. Install the cooker hood directly above the hob. The recommended distance between the hob and the lower edge of the cooker hood is a minimum of 650mm and a maximum of 700mm.

3. To get the best performance, do not make the exhaust pipe too long. Try to make the bend of the exhaust pipe less pronounced and as wide as possible, and ensure the connection is airproof.

4. After hanging the unit on the wall, ensure the hood is level and vertical.

5. The air outlet must not be connected to chimney flues or combustion gas ducts. Under no circumstances should the air outlet be connected to ventilation ducts for a room in which fuel-burning appliances are installed.

SAFETY WARNING: The hood may have very sharp edges. Please wear protective gloves if it is necessary to remove any parts for installing, cleaning, or servicing.

The installation procedure for the PREMIUM PCH797DR is as follows:

Step 1: Place the cooker hood on the wall and mark the position where you want to install it. The recommended height from the hob to the lower edge of the hood is between 650mm and 700mm.

Step 2: Mark four holes on the wall as indicated in the manual’s diagram. Drill 4 holes of 8mm diameter and 60-70mm in depth in the wall where you marked. Press the 4 expanding tubes into the holes. Tighten the 4 wood screws (5x60mm) supplied with the hood into the expanding tubes. Make sure it’s fixed enough and cannot move.

Step 3: Hang the cooker hood on the 2 wood screws. Tighten the 2 wood screws from the position of the filters to the expanding tube. If the hood is slightly tilted, use the adjustable screws to make it level.

Step 4: Fix the exhaust pipe (153mm diameter side) to the shutter.

Step 5: Fix the hook to the inner chimney with M4 screws.

Step 6: Put the inner chimney into the outer chimney. Please note that the inner chimney must be fixed to the outer chimney’s orientation slot.

Step 7: Put the outer chimney onto the unit body and use two M4x10 screws to fix the outer chimney to the unit body.

Step 8: Extend the inner chimney to the desired height. Mark the two holes of the inner chimney’s hook on the wall. Gently put down the inner duct cover and drill two holes (60-70mm depth) using an 8mm drill bit. Press the expanding tubes into the holes. Extend the inner chimney again and tighten it to the expanding tubes with two 5×60 wood screws.

Step 9: Extend the exhaust pipe to the vent-pipe of your building or to the outside. Try to make the bend of the exhaust pipe more than 120°.

Step 10: Install the filter. Put the fix pin into the fix hole and gently press down the filter’s clip.

The control panel on your PREMIUM PCH797DR cooker hood has several functions:

Timer/Clock Button:

Timer: When the hood is working, touch this button once to set the timer. Each additional touch adds one minute. The maximum timer duration is 60 minutes.

Clock: When the hood is not working, touch and hold this button for 3 seconds. The display will show “88:88”. You can then use the “Fan” button to set the “hour” and the “Light” button to set the “minute”. When the hood is off, touching and holding this button for 3 seconds will set the clock.

Fan Button:

Touch this button to start the motor at high speed. Touch it again for middle speed. Touch it a third time for low speed. A fourth touch will stop the motor.

Light Button:

Touch this button once to turn the light on. Touch it again to turn the light off.

Motor On/Off Button:

1. When the hood is working, touch this button once to prolong the working time by one minute.

2. Touch it two times to turn the hood off at once.

CAUTION: NEVER PUT YOUR HAND INTO THE AREA HOUSING WHILE THE FAN IS OPERATING.

For the optimal level of operation, clean the range hood surface, fan, and filter regularly.

1. Use only mild soap or detergent solutions to clean the cooker hood surface. Dry surfaces using a soft cloth.

2. Use a stainless steel cleaner to bring the glow back into a stainless steel finish.

3. Clean the aluminum filter once a week or according to use status. Press the buckle of the aluminum filter slightly, take off the aluminum filter, and put it into warm soapy water using mild detergent. Wipe the filter with a soft brush. Replace the filter after it is dry.

4. Clean the motor fan and other inside parts once every half year or according to use by a QUALIFIED PERSON.

5. DO NOT clean the motor with water or other liquid.

Caution: The lamp unit may be hot! Wait until the unit is cool. Use the same type of lamp. Make sure all control switches are off and the cooker hood is unplugged.

Warning: Make sure the bulb is cool before you touch it!

1. Take out the filters and cut off the wire connection of the lamp.

2. Press the spring according to the arrow direction, then you can take off the lamp unit.

3. You can replace it with a new halogen lamp unit of no more than the specified rating.

If you need to replace only the bulb, follow these steps:

A. Loosen the four screws of the lamp unit and take off the bottom cover.

B. Take out the light bulb assembly.

C. Take out the old light bulb and replace it with a new one.

D. Put the light bulb assembly back in the lamp cup.

E. Put the bottom cover on the lamp.

F. Fix the lamp with four screws.

4. Put the lamp unit back into the hood in the reverse direction. Connect the wire of the lamp.

5. Fit on the filters.

Caution: An LED lamp requires replacement of the entire LED lamp unit, not just a bulb. Make sure all control switches are off and the cooker hood is unplugged.

1. Take out the filters and cut off the wire connection of the lamp.

2. Press the spring according to the arrow direction, then you can take off the lamp unit.

3. You can replace it with a new LED lamp unit of no more than the specified rating.

4. Put the lamp unit back into the hood in the reverse direction and connect the wire of the lamp.

5. Fit on the filters.

Caution: The lamp unit may be hot! Wait until the unit is cool. Use the same type of light bulb. Make sure all control switches are off and the cooker hood is unplugged.

Warning: Make sure the bulb is cool before you touch it!

1. Take out the filters.

2. Loosen the old light bulb.

3. Replace it with a new light bulb of the same type and no more than the specified rating.

4. Fit on the filters.

Please follow these important safety instructions when using your PREMIUM PCH797DR:

• Do not connect the air outlet to chimney flues or combustion gas ducts.

• Do not leave naked flames under this hood.

• In case of any damage to the power cable, have it replaced by a qualified person.

• Clean the hood correctly in accordance with the instructions to avoid the possibility of a fire accident.

• Bulb replacement should be undertaken by a qualified electrician or a competent person. Always use a bulb with a rating no higher than specified.

• Dress in protective gloves before you start to clean the hood. Remove components gently during cleaning.

• Never wash the control switch with water or any other liquid to avoid electrical problems.

• Cleaning the motor fan should be undertaken by a qualified person. Pay close attention to avoid any distortion of the fan during cleaning.

• Never pull the plug out of the power supply with a wet hand to avoid the possibility of electric shock.

• Disconnect the cooker hood from the power supply if this appliance will not be used for a long time.

CAUTION: Disconnect the power supply before servicing.

STATUS	CAUSE AND METHOD OF REPAIRING	TOOL
The power supply is damaged	If the power supply is damaged, please call the technicians to repair.	“+” type Screwdriver, Sharp Pincers
The lamp works but the motor does not run	a) Remove the vane guard and rotate the vane by hand. If the vane cannot move smoothly, the core or bearings of the motor may be damaged. In this case, replace with a new motor. b) If the motor stops running and has a bad odor after a moment of operation, the motor wires may be burnt out. Replace the motor. c) If the starting wire (yellow) is disengaged from the condenser, it needs to be rewired. d) If the condenser is damaged, replace with a new one.	“+” type Screwdriver
The lamp works but the motor does not run (Oil Leak)	a) Take off the filter and check if the connection between the air inlet and wind chamber is sealed. b) Check if the connection between the air exhaust pipe and wind chamber leaks oil. If “YES”, please fill it up with varnish or thinner.	“+” type Screwdriver
Machine vibration	a) If the motors were not firmly screwed, tighten them up. b) If the vane is damaged or unbalanced, replace with a new one.	“+” type Screwdriver
Weak suction	a) The distance is too far between the Range Hood and the Gas Cooker. b) There are many windows (doors) causing strong wind convection. c) If the Range Hood is set upon a window, the best solution is to put a three-ply board on the back of the Range Hood to cover the hollow of the window.	“+” type Screwdriver
Installation of the model is tilted	a) Adjust the height of the model where it hangs on the ceiling. b) If the model tilts forward, lock it into the wall with a wood screw again (the screw should peep out around 0.5 ~1 cm from the wall), or check if the fixing screws are loose.	“+” type Screwdriver
Bulb does not light	Just screw off the lamp shade and replace with a new bulb, then put the lamp shade back.	“+” type Screwdriver

The symbol on your PREMIUM PCH797DR indicates that the product is marked according to the Waste of Electrical and Electronic Equipment (WEEE) directive. This means that WEEE should be separately collected and treated. If at any time in the future you need to dispose of this product, please do NOT dispose of it with household waste. Please send this product to WEEE collecting points where available.