LELO INSIGNIA (02) PDF Document

To begin using your LELO INSIGNIA, follow these initial steps:

1. Before first use, charge the massager for 2 hours.

2. Prepare the remote by inserting 2 x AAA batteries. Lock the battery cover using the provided plastic key.

3. Turn on the massager by pressing and holding the center button for 1-2 seconds until the light activates.

4. To use the device with the remote, press the remote’s + button to activate the wireless connection. The massager will lower its vibrations and enter SenseMotion mode 1.

Note: It may take up to 5-10 seconds for the massager to detect the remote.

The LELO INSIGNIA features a DC charging port concealed by a detachable base attachment. To charge the device:

1. Unscrew the base attachment of your massager by turning it counterclockwise.

2. Insert the DC plug into the DC port.

3. The light on the massager will pulse to indicate it is charging. When fully charged (after approximately 2 hours), the light will emit a steady white glow.

4. After charging, screw the base attachment back on tightly, especially if you plan to use the device in water.

Only use original chargers provided by LELO for the LELO INSIGNIA.

If the power in your LELO INSIGNIA massager is running low, the light will flash rapidly during operation. For the best performance, ensure the massager is fully charged and that high-quality brand batteries are used in the remote to maintain a strong signal.

Follow these steps to manage the batteries for your LELO INSIGNIA remote:

1. Lift off the battery cover. If it is locked, use the plastic key to make a 10-degree turn counterclockwise.

2. Insert 2 x AAA batteries, ensuring the polarity matches the markings in the compartment.

3. Place the cover back on the battery compartment, making sure the ridges are aligned.

4. Insert the plastic key into the slot on the cover and do a 10-degree twist clockwise to lock it shut. Alternatively, you can use flattened palms on either side of the remote to push and twist the lid.

Always ensure the remote is fastened shut before using it in water. Do not use tools like coins as they may damage the surface.

SenseMotion Mode 1 allows you to control the LELO INSIGNIA massager through the tilt of the remote:

1. Turn on the remote by pressing the + button. Once the wireless connection is established, the lights on both the massager and remote will illuminate.

2. Intensify vibrations by tilting the remote. When the remote is moved from a horizontal position to a vertical position, the vibration strength increases to the maximum level.

3. To turn off the remote’s own vibrations while keeping the massager active, press and hold the center button for 5 seconds. The remote will flash instead of vibrating. Repeat this process for 5 seconds to reactivate remote vibrations.

To use SenseMotion Mode 2 with your LELO INSIGNIA:

1. While in SenseMotion Mode 1, press the center button on your remote once.

2. In this mode, you can alter or intensify vibrations by moving the remote in any direction. Faster movements will increase the intensity of the vibrations up to 100%.

The LELO INSIGNIA includes 6 pre-programmed vibration modes:

1. Press the center button on the remote for a third time to access mode 3, which is the first of the 6 pre-programmed patterns. The light on the remote will not be illuminated in these modes.

2. Use the + button to increase vibration intensity and the – button to decrease it.

3. Press the center button to cycle through the different vibration modes. Once you have cycled through all 6 patterns, the massager will return to SenseMotion mode 1.

4. To lock the control interface and prevent accidental activation during travel, hold down the + and – buttons simultaneously for 3 seconds. Hold them again for 3 seconds to unlock.

Yes, you can operate the LELO INSIGNIA massager independently:

1. Turn on the massager by pressing the center button on the device itself. Do not turn on the remote.

2. Press the center button again to turn on vibrations.

3. Continue to press the button to cycle through the 6 pre-programmed vibration patterns. In this manual mode, vibrations are set to 100% intensity. To alter intensity, you must use the remote.

To power down your LELO INSIGNIA:

1. Turn off the remote by holding down the – button for approximately 3 seconds.

2. Turn off the massager by holding down its center button for approximately 3 seconds.

Note: if only the remote is turned off, the massager will enter standby mode for 1 hour, remaining receptive to signals, before turning itself off completely.

The LELO INSIGNIA Oden 2 is a couples’ ring designed to transfer vibrations to both partners. Follow these usage guidelines:

1. While the penis is erect, hold the base attachment and bend the flexible portion to a suitable width to slip it around the penis with the pleasure point facing outwards.

2. For clitoral stimulation, wear the pleasure point facing upwards. Rotate it downwards toward the testicles for alternative stimulation.

3. Note that this device is primarily intended for external massage; internal use may reduce wireless performance.

4. The Oden 2 Design Edition includes an additional closed-ring base for greater constriction. To use it, unscrew the standard base counterclockwise and screw on the alternate attachment. This can be worn either above or below the scrotum.

The LELO INSIGNIA Lyla 2 is designed for both external and internal use. Follow these steps for internal use:

1. Wear the device 2 to 3 inches inside the vagina.

2. Ensure the retraction leash remains outside the body for easy removal and to maintain a wireless connection.

3. You may use a small amount of water-based lubricant to aid insertion. Take care not to bend or damage the pin located beside the DC charging port.

The LELO INSIGNIA Tiani 2 can be used individually or during intercourse. Follow these guidelines:

1. Bend the flexible tail to a 90-degree angle and insert it into the vagina. Lay the vibrating pleasure point over the clitoris.

2. Use a water-based lubricant on the flexible tail to facilitate entry. Note that internal use of the vibrating pleasure point portion may reduce wireless performance.

3. The Tiani 2 Design Edition comes with an additional base attachment for G-spot stimulation. To use it, unscrew the standard base counterclockwise and screw on the alternate channeled attachment. This attachment is designed to stay focused on the G-spot.

To maintain your LELO INSIGNIA and increase its lifespan, follow these care instructions:

1. Only use water-based lubricants. Avoid silicone-based lubricants as they can make the silicone permanently tacky.

2. Never use massage oil or hand cream as lubricants.

3. Clean the device thoroughly before and after each use using a purpose-made antibacterial cleaning spray or warm water and antibacterial soap. Rinse with clean hot water and pat dry with a lint-free cloth.

4. Avoid getting water into the DC socket. Never use cleansers containing alcohol, petrol, or acetone.

5. Store the device in a dust-free place, away from direct sunlight, extreme heat, and toys of other materials.

Refer to these troubleshooting steps for the LELO INSIGNIA:

Massager light does not pulse when connected to the charger:

– The battery may already be fully charged.

– If the battery is completely drained, it may take several minutes to acknowledge the charge.

– Verify the charger is properly connected to the wall and DC sockets.

Remote does not activate when the + button is pressed:

– The batteries may be depleted and need replacement.

– The remote may be locked. Hold the + and – buttons for 3 seconds to unlock.

No connectivity between massager and remote:

– Power off both devices. Activate the remote first by pressing the + button, then press and hold the activation button on the massager for 1 second.

– Ensure both devices are charged or have fresh batteries.

Additional common specs for LELO INSIGNIA:

– Materials: PC-ABS / body-safe silicone with matte silicone and glossy ABS finish.

– Max Noise Level: Less than 50dB.

– Standby Time: Up to 90 days for massagers.

– Interface: 3-button interface, 8 modes, 2-axis motion control function.