LELO IDA WAVE (01) PDF Document

The LELO IDA WAVE should only be used by individuals aged 18 years and over. Persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, should only use the device if they have been given supervision or instruction concerning its safe use and understand the involved hazards. Minors must not play with the product and should not clean or use the product unsupervised.

The LELO IDA WAVE consists of the following components:

Dual stimulation massager body

Charging port

Vibrator head (designed for contact with skin)

Vibrator tail (designed for contact with skin)

Step 1. Before the first use, charge your LELO IDA WAVE for 2 hours.

Step 2. Press the (( )) button to turn the device on.

Step 3. The LED lights will blink to show the current battery level.

Step 4. The LED lights will then go steady, indicating the vibration level.

Step 5. Press the (( )) button to switch between modes, which will be set to 100% intensity.

Step 6. Press the center button for 3 seconds to turn the device off.

Step 1. Charge the LELO IDA WAVE for 2 hours before its first use.

Step 2. Press the (( )) button for 3 seconds to turn it on while simultaneously activating Bluetooth.

Step 3. All LED lights will blink at the same time to show it is in Bluetooth pairing mode.

Step 4. Open the application and locate the toy icon at the bottom of the screen. Find your LELO IDA WAVE and select “Connect”.

Step 5. Press and hold the button on your device. Confirm the connection by pressing the button on your product again.

Step 6. Go to “MY LELO TOYS” and select “PLAY”.

Step 7. Choose between three different control modes.

Step 8. Select “SETTINGS” if you wish to configure an additional four modes.

Step 9. To save these settings for offline use, select “SAVE” at the bottom of the screen.

Step 10. You can use the drop-down menu to set a default auto power-off timer between 10 and 20 minutes. Battery levels can be checked in the upper left corner of the app.

The LELO IDA WAVE is designed to provide stimulation to the clitoris, outer labia, inner labia, and vagina. For an even more pleasurable sensation, it is recommended to apply a liberal amount of LELO Personal Moisturizer to your body and to the LELO IDA WAVE before and during use.

To charge the device, insert the DC plug into the DC port at the base of your LELO IDA WAVE and insert the main plug into a USB port. Only use original chargers provided by LELO.

Pulsing LED: Indicates the device is currently charging.

Steady Glow LED: Indicates the device is fully charged.

Blinking White LED: Indicates the battery is running low.

The LELO IDA WAVE is fully waterproof. To clean it, rinse and spray it with LELO Toy Cleaner, then rinse again and allow it to dry. Alternatively, you can wash the silicone with warm water and antibacterial soap, rinse with clean hot water, and pat dry with a lint-free cloth or towel.

Do not use cleansers containing alcohol, petrol, or acetone.

Avoid using hand creams or silicone-based lubricants with the device, as these may make the silicone permanently tacky.

Avoid leaving your LELO IDA WAVE in direct sunlight and never expose it to extreme heat. Store the device in a dust-free place and keep it away from products made of other materials.

If the LED does not pulse when the charger is connected:

The battery may be completely drained and might require several minutes to acknowledge it is being charged.

The charger may not be properly connected; check both the wall and DC sockets.

If the device does not activate when the center button is pressed:

The battery is empty and needs to be recharged.

The appliance must only be supplied at SELV (Safety Extra Low Voltage).

Step 1. Open the LELO APP.

Step 2. Click “Menu”.

Step 3. Click “Legal & Regulatory”.

Step 4. Click “LELO IDA WAVE”.

The FCC ID is ZT5-IDAWAVE and the IC is 9798A-IDAWAVE.

The LELO IDA WAVE should not be treated as household waste. It should be brought to an appropriate collection point for the recycling of electrical and electronic equipment, as indicated by the crossed-out dustbin symbol on the product.