HIKVISION DS-K1T607TMFWW (01) PDF Document

When using your HIKVISION DS-K1T607TMFWW, please adhere to the following safety instructions:

Dangers:

• All electronic operations should strictly comply with electrical safety regulations and fire prevention regulations in your local region.

• Use the provided power adapter. This equipment is intended to be supplied from a Class 2 surge-protected power source rated DC 12V, 3A.

• Do not connect several devices to one power adapter to avoid overload, which may cause overheating or fire hazards.

• Ensure the power is disconnected before you wire, install, or dismantle the device.

• When the product is installed on a wall or ceiling, it must be firmly fixed.

• If you notice smoke, odors, or noise, turn off the power immediately, unplug the power cable, and contact the service center.

• Do not ingest the battery; there is a Chemical Burn Hazard. This product contains a coin/button cell battery. If swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. Seek immediate medical attention if you think batteries have been swallowed or placed inside any part of the body.

• If the product does not work correctly, contact your dealer or the nearest service center. Do not attempt to disassemble the device yourself.

Cautions:

• Do not drop the device or subject it to physical shock. Avoid exposing it to high electromagnetism radiation and installing it on vibrating surfaces.

• Do not place the device in extremely hot, cold, dusty, or damp locations. Refer to the specifications for the detailed operating temperature.

• The device cover for indoor use should be kept away from rain and moisture.

• Do not expose the equipment to direct sunlight, low ventilation, or heat sources like heaters or radiators.

• Do not aim the device at the sun or other extra-bright places, as this can affect the sensor’s endurance.

• Use the provided glove when opening the device cover to avoid direct contact, as acidic sweat from fingers can erode the surface coating.

• Use a soft, dry cloth for cleaning the inside and outside surfaces of the device cover. Do not use alkaline detergents.

• Improper use or replacement of the battery may result in an explosion hazard. Replace only with the same or equivalent type. Dispose of used batteries according to the manufacturer’s instructions.

• Biometric recognition products are not 100% applicable to anti-spoofing environments. For higher security, use multiple authentication modes.

• The working temperature is -30 °C to +60 °C.

• For indoor installation, the device should be at least 2 meters from any light source and at least 3 meters from a window or door. For outdoor installation, apply silicone sealant around the cable wiring area to prevent rain from entering.

• The protection level is IP65.

The available models for the Face Recognition Terminal are listed below:

The following table describes the main components of the HIKVISION DS-K1T607TMFWW face recognition terminal:

• If installing the HIKVISION DS-K1T607TMFWW indoors, the device should be at least 2 meters away from any light source and at least 3 meters away from a window or door.

• If installing the device outdoors, you should apply silicone sealant around the cable wiring area to protect it from rain.

• Ensure the environment illumination is more than 100 Lux.

• Ensure the output of the external power supply fulfills LPS requirements.

Follow these steps to install the HIKVISION DS-K1T607TMFWW with a gang box:

Step 1. Stick the mounting template on the wall or other surface, ensuring the datum line is 1.4 meters above the ground.

Step 2. Drill holes according to the mounting template and install the gang box.

Step 3. Use two supplied screws (4_KA4 × 22-SUS) to secure the mounting plate to the gang box.

Step 4. Use another four supplied screws to secure the mounting plate to the wall.

Step 5. Remove the two screws on the rear panel and remove the sheet to display the wiring terminals.

Step 6. Route the cable through the cable hole of the mounting plate and connect it to the corresponding external devices’ cables.

Step 7. Reinstall the sheet back onto the device with the two screws.

Step 8. Apply silicone sealant around the cable wiring area to prevent rain from entering.

Step 9. (Optional) If your model has a fingerprint module, insert it into the holes at the bottom of the main part.

Step 10. Align the device with the mounting plate and hang it on the plate.

Step 11. Use two supplied screws (SC-M4 × 12TP10-SUS) to secure the device to the mounting plate.

Follow these steps to install the HIKVISION DS-K1T607TMFWW without a gang box:

Step 1. Stick the mounting template on the wall or other surface, with the datum line 1.4 meters above the ground.

Step 2. Drill 6 holes in the wall according to Hole 1 and Hole 2 on the mounting template.

Step 3. Insert the screw sockets of the setscrews into the drilled holes.

Step 4. Align the 6 holes on the mounting plate with the drilled holes.

Step 5. Remove the two screws on the rear panel and remove the sheet to access the wiring terminals.

Step 6. Route the cable through the cable hole of the mounting plate and connect to the cables of corresponding external devices.

Step 7. Install the sheet back onto the device with the two screws.

Step 8. Apply silicone sealant around the cable wiring area to prevent rain from entering.

Step 9. Insert the fingerprint module (if applicable) into the holes at the bottom of the main part.

Step 10. Align the device with the mounting plate and hang it on the plate.

Step 11. Use two supplied screws (SC-M4 × 12TP10-SUS) to secure the device to the mounting plate.

The HIKVISION DS-K1T607TMFWW contains terminals for power input, alarm input, alarm output, RS-485, Wiegand, and door lock. The descriptions are as follows:

You must activate the HIKVISION DS-K1T607TMFWW before the first login. The default values are:

• Default IP address: 192.0.0.64

• Default port No.: 8000

• Default user name: admin

To activate via the device:

Step 1. After powering on the device, the system will switch to the Device Activation page.

Step 2. On the Activate Device page, create a strong password and confirm it. A strong password should have a minimum of 8 characters and include at least three of the following: uppercase letters, lowercase letters, numbers, and special characters.

Step 3. Tap “Activate,” and the device will be activated.

To perform the first login on your HIKVISION DS-K1T607TMFWW after activation:

Step 1. Long tap on the initial page for 3 seconds to enter the password entry page.

Step 2. Tap the Password field and enter the device activation password you created.

Step 3. Tap OK to enter the home page.

Note: The device will be locked for 30 minutes after 5 failed password attempts.

After you have added an administrator for the HIKVISION DS-K1T607TMFWW, only the administrator can log in for device operation. Follow these steps:

Step 1. Long tap on the initial page for 3 seconds to enter the admin login page.

Step 2. Authenticate using the administrator’s face, fingerprint, or card to enter the home page.

Note: The device will be locked for 30 minutes after 5 failed fingerprint or card attempts. You can also tap the lock icon and enter the device activation password to log in.

You can set the network parameters, including IP address, subnet mask, and gateway, on the HIKVISION DS-K1T607TMFWW.

Step 1. Tap Comm. (Communication Settings) on the Home page.

Step 2. On the Communication Settings page, tap Network to enter the Network tab.

Step 3. Tap IP Address, Subnet Mask, or Gateway and input the required parameters.

Step 4. Tap OK to save the settings.

Step 5. Tap the checkmark icon to save the network parameters.

Adding an administrator allows that user to log in to the device backend and configure parameters. Follow these steps:

Step 1. Tap User → + to enter the Add User page.

Step 2. Edit the employee ID. It should be less than 32 characters (letters and numbers) and not start with 0.

Step 3. Tap the Name field and input the user name (up to 32 characters).

Step 4. (Optional) Add a face picture, fingerprint, card, or password for the administrator.

Step 5. (Optional) Set the administrator’s authentication type.

Step 6. Enable the “Enable Administrator Permission” function. This allows the user to access the Home page for operations after authentication.

Step 7. (Optional) Tap the Schedule Template field to select and save a schedule template.

Step 8. Tap the checkmark icon to save the settings.

To add a user’s face picture for authentication on the HIKVISION DS-K1T607TMFWW:

Step 1. Tap User → + to enter the Add User page.

Step 2. Edit the employee ID.

Step 3. Tap the Name field and input the user name.

Step 4. Tap the Face Picture field to enter the face picture adding page.

Step 5. Position your face looking at the camera. Ensure your face is within the outline on the screen and the picture is of good quality.

Step 6. Tap Save to save the face picture. A captured picture will be displayed in the upper right corner.

Step 7. (Optional) Tap Try Again to adjust your face position and add the picture again. The maximum duration for this process is 15 seconds.

Step 8. Enable or disable Administrator Permission as needed.

Step 9. Tap the checkmark icon to save all settings.

To add a user’s fingerprint on a compatible HIKVISION DS-K1T607TMFWW model:

Step 1. Tap User → + to enter the Add User page.

Step 2. Tap the Employee ID field and edit the employee ID.

Step 3. Tap the Name field and input the user name.

Step 4. Tap the Fingerprint field to enter the Add Fingerprint page.

Step 5. Place your finger on the fingerprint module and follow the on-screen instructions to record the fingerprint.

Step 6. After the fingerprint is added completely, tap Yes on the pop-up dialog to save it and add another fingerprint.

Step 7. (Optional) Tap No to save the fingerprint and return to the Add User page. You can add up to 10 fingerprints for one user. The same fingerprint cannot be added repeatedly.

Step 8. Tap the checkmark icon to save the settings.

On the System Settings page of your HIKVISION DS-K1T607TMFWW, you can set basic parameters, face parameters, fingerprint parameters, and manage firmware.

To access System Settings, tap System on the Home page.

Basic Parameters:

You can set community No., building No., unit No., voice prompt, voice volume, application mode, wake-up distance, IR light brightness, and white light brightness.

Face Picture Parameters:

You can configure face recognition settings such as security levels, anti-spoofing, and detection margins.

Fingerprint Parameters:

You can set the fingerprint security level. A higher level results in a lower false acceptance rate (FAR) but a higher false rejection rate (FRR).

You can set access control permissions like authentication mode, NFC anti-cloning, anti-passback, and various alarms. On the Home page, tap ACS (Access Control Settings) to enter the page. Edit the parameters and tap the checkmark icon to save.

The available parameters are described below:

Upgrade Firmware:

Plug in a USB flash drive with the upgrade file (digicap.dav) in the root directory. Tap Maint. (Maintenance) on the System Settings page and tap Upgrade. The device will automatically read the file and upgrade the firmware. Do not power off the device during the upgrade.

Data Management:

Tap Data (Data Management) to enter the Data Management page. Here you can perform the following actions:

Log Query:

On the Home page, tap Log to enter the Log page. You can search authentication logs by employee ID, card No., or user name within a specified time period.

Recommended Finger:

Use your forefinger, middle finger, or third finger.

Correct Scanning:

Press your finger on the scanner horizontally. The center of your scanned finger should align with the center of the scanner.

Incorrect Scanning:

Avoid placing your finger vertically, on the edge, or sideways on the scanner.

Environment:

The scanner should be protected from direct sunlight, high temperature, humid conditions, and rain. If your finger is too dry, the scanner may not recognize it. You can try blowing on your finger and scanning again.

Others:

If your fingerprint is shallow or hard to scan, it is recommended to use other authentication methods. If the scanned finger has injuries, the scanner may not recognize it; try using a different finger.

To ensure good quality and accurate face recognition with the HIKVISION DS-K1T607TMFWW, follow these tips:

Positions (Recommended Distance: 0.5 m):

Ensure you are at the recommended height (1.4 m to 1.9 m) and not too high, too low, too close, or too far from the device.

Expression:

• Keep a natural expression, similar to a standard portrait photo.

• Do not wear a hat, sunglasses, or other accessories that could obstruct the facial recognition function.

• Ensure your hair does not cover your eyes or ears. Heavy makeup is not allowed.

Posture:

Position your face looking directly at the camera. Avoid tilting your head up, down, or to the side.

Size:

Make sure your face is centered within the collecting window. Avoid being too close or too far away.

The wake-up distance of the HIKVISION DS-K1T607TMFWW varies depending on the environment, including lighting conditions and the surface behind the user. The following table provides examples: