HIKVISION DS-K1T607PMFW (01) PDF Document

The symbols found in the user manual for your HIKVISION DS-K1T607PMFW are defined as follows:

Please follow these safety instructions to ensure the correct operation of your HIKVISION DS-K1T607PMFW and to avoid danger or property loss.

Dangers:

• All electronic operations should strictly comply with electrical safety regulations, fire prevention regulations, and other related regulations in your local region.

• Use the provided power adapter. The equipment is intended to be supplied from a Class 2 surge-protected power source rated DC 12V, 3A.

• Do not connect several devices to one power adapter to avoid overload, which may cause overheating or fire hazards.

• Ensure the power is disconnected before you wire, install, or dismantle the device.

• When installed on a wall or ceiling, the device must be firmly fixed.

• If smoke, odors, or noise rise from the device, turn off the power immediately, unplug the power cable, and contact the service center.

• This product contains a coin/button cell battery. Do not ingest the battery as it is a Chemical Burn Hazard. If swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. Seek immediate medical attention if you think batteries might have been swallowed or placed inside any part of the body.

• If the product does not work properly, contact your dealer or the nearest service center. Do not attempt to disassemble the device yourself.

Cautions:

• Do not drop the device or subject it to physical shock. Do not expose it to high electromagnetism radiation. Avoid installation on vibrating surfaces or places subject to shock.

• Do not place the device in extremely hot, cold, dusty, or damp locations. Refer to the device specifications for detailed operating temperatures.

• The device cover for indoor use should be kept from rain and moisture.

• Do not expose the equipment to direct sunlight, low ventilation, or heat sources like heaters or radiators.

• Do not aim the device at the sun or extra bright places to avoid blooming or smear, which can affect the sensor’s endurance.

• Use the provided glove when opening the device cover to avoid direct contact, as acidic sweat from fingers can erode the surface coating.

• Use a soft and dry cloth for cleaning inside and outside surfaces. Do not use alkaline detergents.

• Keep all original wrappers for future use. Transportation without the original wrapper may cause damage and lead to additional costs.

• Improper use or replacement of the battery may result in an explosion hazard. Replace only with the same or equivalent type. Dispose of used batteries according to the manufacturer’s instructions.

• Biometric recognition products are not 100% applicable to anti-spoofing environments. For higher security, use multiple authentication modes.

• The working temperature is -30 °C to +60 °C.

• For indoor use, the device should be at least 2 meters away from light and at least 3 meters away from a window or door. For outdoor use, apply silicone sealant around the cable wiring area to prevent rain from entering.

• The protection level is IP65.

The HIKVISION DS-K1T607 series has different features depending on the specific series.

Features (Normal Series):

• 7-inch LCD touch screen

• 2 MP wide-angle dual-lens

• Manually adjusts supplement light brightness

• Face recognition distance: 0.3 m to 1.5 m

• Suggested height for face recognition: 1.4 m to 1.9 m

• Deep learning algorithm

• 6,000 face capacity, 5,000 fingerprint capacity, and 10,000 event capacity

• Multiple authentication modes

• Face recognition duration ≤ 0.5 s/User; accuracy rate ≥ 99%

• Stand-alone operation and device parameter management

• Imports data via TCP/IP or USB flash drive

• Connects to external card reader/access controller via RS-485 or Wiegand protocol

• Two-way audio with client software, door station, indoor station, and master station

Features (P Series):

• Includes all Normal Series features plus:

• Face recognition in dark environment

• 10,000 face capacity, 5,000 fingerprint capacity, and 50,000 event capacity

• Watchdog design and tamper function

• NFC tag anti-cloning

Features (T Series):

• Includes all P Series features plus:

• 50,000 face capacity, 5,000 fingerprint capacity, and 50,000 event capacity

The components of the HIKVISION DS-K1T607PMFW are described in the table below:

• If installing the device indoors, it should be at least 2 meters away from the light, and at least 3 meters away from the window or the door.

• If installing the device outdoors, you should apply Silicone sealant among the cable wiring area to keep the raindrop from entering.

• Make sure the environment illumination is more than 100 Lux.

• Make sure the output of the external power supply fulfills LPS.

Follow these steps to install your HIKVISION DS-K1T607PMFW with a gang box:

Step 1. Stick the mounting template on the wall or other surface, 1.4 meters higher than the ground, using the datum line as a guide.

Step 2. Drill holes according to the template and install the gang box.

Step 3. Use two supplied screws (4_KA4 × 22-SUS) to secure the mounting plate on the gang box.

Step 4. Use another four supplied screws to secure the mounting plate on the wall.

Step 5. Remove the two screws on the rear panel and remove the sheet to display the wiring terminals.

Step 6. Route the cable through the cable hole of the mounting plate and connect to the corresponding external devices’ cables.

Step 7. Install the sheet back to the device with the two screws.

Step 8. Apply Silicone sealant among the cable wiring area to keep rain from entering.

Step 9. (Optional) Insert the fingerprint module into the holes at the bottom of the main part.

Step 10. Align the device with the mounting plate and hang it on the plate.

Step 11. Use two supplied screws (SC-M4 × 12TP10-SUS) to secure the device to the mounting plate.

Follow these steps to install your HIKVISION DS-K1T607PMFW without a gang box:

Step 1. Stick the mounting template on the wall or other surface, 1.4 meters higher than the ground, using the datum line as a guide.

Step 2. Drill 6 holes on the wall or other surface according to Hole 1 and Hole 2 on the mounting template.

Step 3. Insert the screw sockets of the setscrews into the drilled holes.

Step 4. Align the 6 holes on the mounting plate with the drilled holes and secure it with the supplied screws.

Step 5. Remove the two screws on the rear panel and remove the sheet to display the wiring terminals.

Step 6. Route the cable through the cable hole of the mounting plate and connect to the corresponding external devices’ cables.

Step 7. Install the sheet back to the device with the two screws.

Step 8. Apply Silicone sealant among the cable wiring area to keep rain from entering.

Step 9. Insert the fingerprint module into the holes at the bottom of the main part.

Step 10. Align the device with the mounting plate and hang it on the plate.

Step 11. Use two supplied screws (SC-M4 × 12TP10-SUS) to secure the device to the mounting plate.

The wiring terminals on the HIKVISION DS-K1T607PMFW are used for power input, alarm input/output, RS-485, Wiegand, and door lock connections. The descriptions are as follows:

You must activate your HIKVISION DS-K1T607PMFW before the first login. You can activate it directly on the device, via the SADP tool, or using client software. The default values are:

• Default IP address: 192.0.0.64

• Default port No.: 8000

• Default user name: admin

Activate via Device:

Step 1. After powering on the device, the system will enter the Device Activation page.

Step 2. On the Activate Device page, create a strong password and confirm it.

Step 3. Tap ‘Activate’, and the device will be activated.

It is highly recommended to use a strong password with a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters.

Activate via SADP:

Step 1. Install the SADP software on a PC on the same subnet as the device.

Step 2. Run the SADP software to search for online devices.

Step 3. Select your inactive device from the list.

Step 4. Input a new strong password and confirm it.

Step 5. Click ‘Activate’ to start the activation.

Step 6. After activation, you can modify the device’s IP address to match your network by selecting the device, changing the IP address manually or enabling DHCP, inputting the admin password, and clicking ‘Modify’.

After activating your HIKVISION DS-K1T607PMFW, you should set the application and recognition modes for optimal performance.

Set Application Mode:

Step 1. On the Welcome page, select ‘Indoor’ or ‘Others’ from the drop-down list.

• Select ‘Others’ if you install the device indoors near a window or if face recognition is not working well.

• If you don’t configure this, the system defaults to ‘Indoor’.

Step 2. Tap OK to save.

Set Recognition Mode:

Step 1. On the Welcome page, after selecting the application mode, select ‘Normal Mode’ or ‘Deep Mode’ from the drop-down list.

• **Normal Mode:** Recognizes faces via the camera normally.

• **Deep Mode:** Can recognize a much wider range of people and is suitable for more complicated environments.

Step 2. Tap OK to save. The system defaults to ‘Normal’ if not configured.

The login procedure depends on whether it is the first login or if an administrator has been added.

Login For First Login:

Step 1. Long tap on the initial page for 3 seconds to enter the password entry page.

Step 2. Enter the device activation password you created.

Step 3. Tap OK to enter the home page. The device will be locked for 30 minutes after 5 failed password attempts.

Login by Administrator:

After an administrator is added, only the administrator can log in to operate the device.

Step 1. Long tap on the initial page for 3 seconds to enter the admin login page.

Step 2. Authenticate using the administrator’s face, fingerprint, or card to enter the home page.

The device will be locked for 30 minutes after 5 failed fingerprint or card attempts. You can also tap the lock icon to enter the device activation password for login.

You can add, edit, and manage users, including administrators, directly from the user management interface on your HIKVISION DS-K1T607PMFW.

Add an Administrator:

Step 1. Tap User → + to enter the Add User page.

Step 2. Edit the employee ID (less than 32 characters, cannot start with 0, must be unique).

Step 3. Input the user name (up to 32 characters).

Step 4. (Optional) Add credentials for the administrator: face picture, fingerprint, card, or password.

Step 5. Enable the ‘Administrator Permission’ function. This allows the user to access the Home page for device operations.

Step 6. Tap the checkmark to save the settings.

Add Face Picture:

Step 1. On the Add User page, tap the Face Picture field.

Step 2. Position your face looking at the camera, ensuring it is within the outline.

Step 3. The device will capture the picture. Tap ‘Save’ to save it. You can tap ‘Try Again’ to recapture.

Add Fingerprint:

Step 1. On the Add User page, tap the Fingerprint field.

Step 2. Follow the on-screen instructions to place and lift your finger on the fingerprint module to record it.

Step 3. After successful recording, a pop-up will appear. Tap ‘Yes’ to save and add another fingerprint, or ‘No’ to save and return to the Add User page. Up to 10 fingerprints can be added for one user.

Add Card:

Step 1. On the Add User page, tap the Card field.

Step 2. Configure the card number by either entering it manually or swiping the card over the card swiping area.

Add Password:

Step 1. On the Add User page, tap the Password field.

Step 2. Create and confirm a password (numbers only, up to 8 characters).

Set Authentication Mode:

On the Add/Edit User page, tap ‘Authentication Mode’ to combine different credentials (e.g., Face and Card) for custom authentication needs.

You can use a USB flash drive to import and export user data, pictures, and parameters on your HIKVISION DS-K1T607PMFW.

Export Data:

Step 1. Tap ‘Transfer’ on the Home page.

Step 2. Tap the data type you want to export (e.g., Export User Data, Export Face Pic., etc.).

Step 3. Tap ‘Yes’ on the pop-up page. The data will be exported to the connected USB flash drive. The system supports USB drives from 1G to 32G with more than 512M of free space.

Import Data:

Step 1. Plug the USB flash drive containing the data into the device.

Step 2. On the Transfer page, tap the data type to import (e.g., Import User Data, Import Face Pic.).

Step 3. Tap ‘Yes’ on the pop-up window. The data will be imported from the USB drive to the device.

For importing pictures, they should be saved in the root directory (in a folder named ‘enroll_pic’) and follow the naming rule: Card No._Name_Department_Employee ID_Gender.jpg. The picture resolution should be 640 × 480 pixels or more, and the size should be between 60 KB and 200 KB.

The HIKVISION DS-K1T607PMFW supports different authentication methods based on the configuration.

Authenticate via 1:1 Matching (e.g., Card and Face):

This method compares the captured credential with the specific user’s stored data.

Step 1. Swipe your card in the card swiping area.

Step 2. Position your face looking at the camera to authenticate your face.

Step 3. If successful, the prompt “Authenticated” will pop up.

Authenticate via 1:N Matching (e.g., Face only):

This method compares the captured credential with all stored data in the device.

Step 1. Position your face looking at the camera to start face authentication.

Step 2. If successful, the prompt “Authenticated” will pop up.

Authenticate via 1:1 and 1:N Matching (e.g., Fingerprint and Face):

Step 1. Authenticate your fingerprint first. The device performs a 1:N match against its database.

Step 2. When the prompt “Continue to authenticate” appears, position your face looking at the camera. The device then performs a 1:1 match with the user information gained from the fingerprint scan.

Step 3. If successful, the prompt “Authenticated” will pop up.

On the System Settings page of your HIKVISION DS-K1T607PMFW, you can configure basic parameters, face parameters, and fingerprint parameters.

Basic Parameters:

Face Picture Parameters:

Fingerprint Parameters:

• **Security Level:** Select the fingerprint security level. A higher level decreases the false acceptance rate (FAR) but increases the false rejection rate (FRR).

You can set the time and attendance mode on your HIKVISION DS-K1T607PMFW to define how attendance is recorded. This function should be used in cooperation with the client software.

Disable Attendance Mode:

Step 1. Tap ‘T&A Status’ on the home page.

Step 2. Set the Attendance Mode to ‘Disable’.

Result: You will not view or configure attendance status on the initial page. The system will follow rules configured on the client software.

Set Manual Attendance:

Step 1. Tap ‘T&A Status’.

Step 2. Set the Attendance Mode to ‘Manual’.

Step 3. Enable the ‘Attendance Status’ function.

Result: You must select the attendance status (e.g., Check In, Check Out) manually after authentication for it to be recorded as a valid attendance event.

Set Auto Attendance:

Step 1. Tap ‘T&A Status’.

Step 2. Set the Attendance Mode to ‘Auto’.

Step 3. Select an attendance status (e.g., Break Out) and set its valid schedule (e.g., Monday 11:00 to Monday 12:00).

Result: When you authenticate on the initial page, the event will be automatically marked with the configured attendance status if it falls within the scheduled time.

Set Manual and Auto Attendance:

This mode allows the system to automatically assign a status based on a schedule, but also gives you the option to manually override it.

Result: If you do not select a status, the authentication will be marked according to the schedule. If you tap ‘Select Status’ and choose one, it will be marked as the selected status.

You can set access control permissions from the device’s home screen. Tap ACS (Access Control Settings) to enter the settings page.

Tap the checkmark to save the settings.

You can perform maintenance tasks from the System Settings page.

Upgrade Firmware:

Step 1. Plug in a USB flash drive containing the upgrade file (digicap.dav) in the root directory.

Step 2. Tap Maint. (Maintenance) on the System Settings page.

Step 3. Tap Upgrade. The device will automatically read the file and upgrade the firmware. Do not power off the device during the upgrade.

Data Management:

Step 1. Tap Data (Data Management) to enter the management page.

Step 2. Tap the button for the action you want to perform:

• **Delete All Events:** Deletes all events stored in the device.

• **Delete User Data:** Deletes all user data in the device.

• **Delete Captured Pic.:** Deletes all captured pictures.

• **Restore to Factory:** Restores the system to factory settings. The device will reboot.

• **Restore to Default:** Restores parameters to default but saves communication and remote user settings. The device will reboot.

Step 3. Tap ‘Yes’ on the pop-up window to confirm.

For best results when scanning your fingerprint on the HIKVISION DS-K1T607PMFW, please follow these tips:

Recommended Finger:

• Use your forefinger, middle finger, or third finger.

Correct Scanning:

• Press your finger on the scanner horizontally. The center of your scanned finger should align with the center of the scanner.

Incorrect Scanning:

• Avoid placing your finger vertically, on the edge of the scanner, or at an angle (side).

Environment:

• The scanner should avoid direct sunlight, high temperature, humid conditions, and rain.

• If your finger is too dry and the scanner cannot recognize it, you can blow on your finger to add moisture and try again.

Others:

• If your fingerprint is shallow or difficult to scan, it is recommended to use other authentication methods.

• If you have injuries on the scanned finger, the scanner may not recognize it. Try using a different finger.

To get a good quality and accurate face picture for recognition on your HIKVISION DS-K1T607PMFW, follow these guidelines:

Positions (Recommended Distance: 0.5 m):

• Position your face directly in front of the camera. Avoid being too high, too low, too close, or too far.

• The recommended height for recognition is between 1.4 m and 1.9 m.

Expression:

• Keep your expression natural, similar to a passport photo.

• Do not wear a hat, sunglasses, or other accessories that could obstruct the facial recognition function.

• Do not let your hair cover your eyes, ears, etc. Heavy makeup is not allowed.

Posture:

• Face the camera directly. Avoid tilting your head up, down, or to the side.

Size:

• Ensure your face is centered in the middle of the collecting window. Avoid being too close or too far from the camera.

The distance at which the HIKVISION DS-K1T607PMFW wakes up and detects a person varies based on the environment, lighting conditions, and the surface behind the person. The following table provides reference distances for short, medium, and long wake-up settings.