HIKVISION DS-K1T607PE (01) PDF Document

The symbols found in the user manual for your HIKVISION DS-K1T607PE are defined as follows:

Please adhere to the following safety instructions to ensure correct use of your HIKVISION DS-K1T607PE and to avoid danger or property loss.

Dangers:

• All electronic operations should strictly comply with electrical safety regulations, fire prevention regulations, and other related regulations in your local region.

• Use the provided power adapter. The equipment is intended to be supplied from a Class 2 surge protected power source rated DC 12V, 3A.

• Do not connect several devices to one power adapter, as an overload may cause overheating or a fire hazard.

• Ensure power is disconnected before you wire, install, or dismantle the device.

• When installed on a wall or ceiling, the device must be firmly fixed.

• If smoke, odors, or noise arise from the device, turn off the power at once, unplug the power cable, and contact the service center.

• Do not ingest the battery; it is a Chemical Burn Hazard. This product contains a coin/button cell battery which can cause severe internal burns and lead to death if swallowed.

• Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.

• If the product is not working properly, contact your dealer or the nearest service center. Do not attempt to disassemble the device yourself.

Cautions:

• Do not drop the device, subject it to physical shock, or expose it to high electromagnetism radiation. Avoid installing on vibrating surfaces.

• Do not place the device in extremely hot, cold, dusty, or damp locations.

• The device cover for indoor use should be kept from rain and moisture.

• Avoid exposing the equipment to direct sunlight, low ventilation, or heat sources like heaters or radiators.

• Do not aim the device at the sun or other extra bright places.

• Use the provided glove when opening the device cover to avoid direct contact, as acidic sweat can erode the surface coating.

• Use a soft, dry cloth for cleaning. Do not use alkaline detergents.

• Keep all original wrappers for future use in case of return for factory repair.

• Improper use or replacement of the battery may result in an explosion hazard. Replace only with the same or equivalent type.

• Biometric recognition is not 100% applicable to anti-spoofing environments. For higher security, use multiple authentication modes.

• For outdoor installation, apply Silicone sealant around the cable wiring area to prevent rain from entering.

• The protection level is IP65.

The components of the HIKVISION DS-K1T607PE are as follows:

• For indoor installation, the device should be at least 2 meters away from any light source and at least 3 meters away from a window or door.

• For outdoor installation, apply Silicone sealant among the cable wiring area to protect against rain.

• Ensure the environmental illumination is more than 100 Lux.

• Ensure the output of the external power supply fulfills LPS (Limited Power Source) requirements.

Follow these steps to install your HIKVISION DS-K1T607PE with a gang box:

Step 1. Stick the mounting template on the wall or other surface, ensuring the datum line is 1.4 meters above the ground.

Step 2. Drill holes according to the template and install the gang box.

Step 3. Use two supplied screws (4_KA4 × 22-SUS) to secure the mounting plate to the gang box.

Step 4. Use another four supplied screws to secure the mounting plate to the wall.

Step 5. Remove the two screws on the rear panel and remove the sheet to expose the wiring terminals.

Step 6. Route the cable through the cable hole of the mounting plate and connect to the corresponding external devices’ cables.

Step 7. Reinstall the sheet back onto the device with the two screws.

Step 8. Apply Silicone sealant around the cable wiring area to prevent rain from entering.

Step 9. Optional: Insert the fingerprint module into the holes at the bottom of the main part.

Step 10. Align the device with the mounting plate and hang it on the plate.

Step 11. Use two supplied screws (SC-M4 × 12TP10-SUS) to secure the device to the mounting plate.

Follow these steps to install your HIKVISION DS-K1T607PE without a gang box:

Step 1. Stick the mounting template on the wall, with the datum line 1.4 meters above the ground.

Step 2. Drill 6 holes on the wall according to Hole 1 and Hole 2 on the mounting template.

Step 3. Insert the screw sockets for the setscrews into the drilled holes.

Step 4. Align the 6 holes of the mounting plate with the drilled holes and secure it with screws.

Step 5. Remove the two screws on the rear panel and remove the sheet to display the wiring terminals.

Step 6. Route the cable through the cable hole of the mounting plate and connect to external devices’ cables.

Step 7. Reinstall the sheet back on the device with the two screws.

Step 8. Apply Silicone sealant in the cable wiring area to prevent rain from entering.

Step 9. Insert the fingerprint module into the holes at the bottom of the main part.

Step 10. Align the device with the mounting plate and hang it on the plate.

Step 11. Use two supplied screws (SC-M4 × 12TP10-SUS) to secure the device to the mounting plate.

The terminals of the HIKVISION DS-K1T607PE are described as follows:

You must activate the device before the first login. After powering on the HIKVISION DS-K1T607PE, it will switch to the Device Activation page.

On the Activate Device page, create a password and confirm it. Tap “Activate,” and the device will be activated.

It is highly recommended to use a strong password with a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters.

After activating the device, you should select an application mode and a recognition mode for optimal performance.

Set Application Mode:

Step 1. On the Welcome page, select “Indoor” or “Others” from the drop-down list.

Step 2. Tap OK to save. If you install the device indoors near a window or if face recognition is not working well, select “Others”.

Set Recognition Mode:

Step 1. After selecting the application mode, select “Normal Mode” or “Deep Mode” from the drop-down list.

• Normal Mode: Recognizes faces via the camera normally.

• Deep Mode: Recognizes a much wider range of people and is suitable for more complicated environments.

Step 2. Tap OK to save.

For the First Login:

Step 1. Long tap on the initial page for 3 seconds to enter the password entering page.

Step 2. Tap the Password field and enter the device activation password you created.

Step 3. Tap OK to enter the home page. The device will be locked for 30 minutes after 5 failed password attempts.

Login by Administrator (after an admin is added):

Step 1. Long tap on the initial page for 3 seconds to enter the admin login page.

Step 2. Authenticate the administrator’s face, fingerprint, or card to enter the home page.

You can manage communication settings from the Home page.

Set Network Parameters:

Step 1. Tap “Comm.” on the Home page.

Step 2. Tap “Network”.

Step 3. Tap IP Address, Subnet Mask, or Gateway and input the parameters.

Step 4. Tap OK to save.

Set Wi-Fi Parameters:

Step 1. Tap “Comm.” on the Home page.

Step 2. Tap “Wi-Fi” and enable the Wi-Fi function.

Step 3. Select a Wi-Fi network from the list.

Step 4. Select an IP mode (Static or Dynamic) and input the required information (password, IP address, etc.).

Step 5. Tap OK to save the settings.

Set RS-485 Parameters:

Step 1. Tap “Comm.” on the Home page.

Step 2. Tap “RS-485”.

Step 3. Select the external device you are connecting (Controller, Unit, or Reader).

Step 4. Tap the check mark to save. The device will reboot if you change the external device.

Set Wiegand Parameters:

Step 1. Tap “Comm.” on the Home page.

Step 2. Tap “Wiegand”.

Step 3. Enable the Wiegand function.

Step 4. Select a transmission direction: “Output” to connect to an external access controller, or “Input” to connect to a Wiegand card reader.

Step 5. Tap the check mark to save. The device will reboot if you change this setting.

To add a user and their credentials, follow these general steps. Note that some functions, like fingerprints, are only available on specific models.

Add a User (can also be an Administrator):

Step 1. Tap “User” → “+” to enter the Add User page.

Step 2. Edit the employee ID (less than 32 characters, cannot start with 0, cannot be duplicated).

Step 3. Tap the Name field and input the user’s name.

Step 4. Add credentials as needed:

• Add Face Picture: Tap the Face Picture field. Position your face in the camera frame and tap Save. You can tap “Try Again” to recapture.

• Add Fingerprint: Tap the Fingerprint field. Follow the on-screen instructions to place and lift your finger on the module to record it. You can add up to 10 fingerprints per user.

• Add Card: Tap the Card field. You can enter the card number manually or swipe the card over the card swiping area to capture the number. Up to 5000 cards can be added.

• Add Password: Tap the Password field and create an 8-digit numerical password.

Step 5. Optional: For an administrator, enable the “Administrator Permission” function.

Step 6. Tap the check mark to save the settings.

Export Data:

Step 1. Tap “Transfer” on the Home page.

Step 2. Tap the data type you wish to export (e.g., Export Att. Data, Export User Data, Export Face Pic.).

Step 3. Tap “Yes” on the pop-up page. The data will be exported to the connected USB flash drive.

Import Data:

Step 1. Plug a USB flash drive containing the data into the device.

Step 2. On the Transfer page, tap the data type you wish to import (e.g., Import User Data, Import Face Pic.).

Step 3. Tap “Yes” on the pop-up window, and the data will be imported from the USB flash drive to the device.

Tap “System” on the Home page to access System Settings. Here you can configure basic parameters, face picture parameters, and fingerprint parameters.

Basic Parameters:

Face Picture Parameters:

Fingerprint Parameters:

You can select the fingerprint security level. The higher the security level, the lower the false acceptance rate (FAR).

Tap “T&A Status” on the Home page to set the attendance mode. This function should be used cooperatively with the client software.

• Disable Attendance Mode: Set Attendance Mode to “Disable”. No attendance status will be shown on the initial page.

• Set Manual Attendance: Set Attendance Mode to “Manual”. You must manually select an attendance status (e.g., check-in, check-out) after authentication.

• Set Auto Attendance: Set Attendance Mode to “Auto”. The system will automatically change the attendance status according to configured schedules.

• Set Manual and Auto Attendance: Set Attendance Mode to “Manual and Auto”. The system works automatically based on schedule, but you can also manually change the status after authentication.

On the Home page, tap “ACS” (Access Control Settings) to configure the following parameters:

Upgrade Firmware:

Step 1. Plug in a USB flash drive with the upgrade file (digicap.dav) in the root directory.

Step 2. Tap “Maint.” (Maintenance) on the System Settings page.

Step 3. Tap “Upgrade”. The device will automatically read the file and upgrade the firmware. Do not power off the device during the upgrade.

Data Management:

Tap “Data” (Data Management) to manage device data. You can perform the following actions:

• Delete All Events: Deletes all events stored in the device.

• Delete User Data: Deletes all user data in the device.

• Delete Captured Pic.: Deletes all captured pictures.

• Restore to Factory: Restores the system to factory settings. The device will reboot.

• Restore to Default: Restores the system to default settings, but saves communication and remote user settings.

Log Query:

On the Home page, tap “Log” to search authentication logs by employee ID, card No., or user name within a specific time period.

You can add your HIKVISION DS-K1T607PE to the client software in several ways after running the client.

Add an Online Device:

Step 1. Enter the Device Management module.

Step 2. Click the “Device” tab.

Step 3. Click “Online Device” to see devices on the same local subnet.

Step 4. Select your device from the list and click “Add”.

Step 5. Enter the required information: Name, User Name (default: admin), and Password.

Step 6. Optionally check “Synchronize Time” and “Import to Group”.

Step 7. Click “Add”.

You can also add devices by IP Address/Domain Name, IP Segment, or by batch import using a CSV template.

The Time and Attendance module in the client software allows you to track employee work hours. The main steps are configuring parameters, creating schedules, and then calculating data.

1. Configure Attendance Parameters:

• Go to “Attendance Settings”.

• Configure “General Rule” (week/month beginning, weekends), “Overtime”, “Attendance Check Point” (specify which card readers are used for attendance), “Holiday” (add regular and irregular holidays), and “Leave Type”.

2. Add Timetable:

• Go to “Time and Attendance” → “Timetable”.

• Click “Add” to create a new timetable.

• Define the timetable name, type (General or Flexible), and calculation method.

• Set start/end work times, valid check-in/out times, and allowances for being late or leaving early.

3. Add Shift:

• Go to “Time & Attendance” → “Shift”.

• Click “Add” to create a new shift, give it a name, and select a shift period.

• Apply the timetables you created to the days of the week for this shift.

4. Manage Shift Schedule:

• Go to “Time & Attendance” → “Shift Schedule”.

• Assign the shifts you created to departments or individual persons.

5. Calculate Attendance Data:

• Go to “Attendance Statistics” → “Calculate Attendance”.

• Set a date range and click “Calculate”. The system will process the records based on your configurations.

6. View Reports:

• After calculating, go to “Attendance Statistics” → “Original Records” or “Report” to view detailed records and generate attendance reports.

For best results when scanning fingerprints on your HIKVISION DS-K1T607PE:

• Recommended Finger: Use your forefinger, middle finger, or third finger.

• Correct Scanning: Press your finger on the scanner horizontally. The center of your finger should align with the center of the scanner. Avoid placing your finger vertically, on the edge, or sideways.

• Environment: The scanner should avoid direct sunlight, high temperature, humid conditions, and rain. If your finger is too dry, the scanner may not recognize it. You can try blowing on your finger before scanning again.

• Other Considerations: If your fingerprint is shallow or hard to scan, it is recommended to use other authentication methods. If you have injuries on the scanned finger, the scanner may not recognize it; try a different finger.

To ensure a good quality and accurate face picture for collection and comparison on your HIKVISION DS-K1T607PE, follow these tips:

• Positions: The recommended distance from the device is 0.5 meters. Ensure your face is not too high, too low, too close, or too far from the camera.

• Expression: Keep your expression natural, similar to a passport photo.

• Accessories: Do not wear a hat, sunglasses, or other accessories that can obstruct the facial recognition function.

• Hair and Makeup: Do not let your hair cover your eyes, ears, etc. Heavy makeup is not allowed.

• Posture: Position your face looking directly at the camera. Avoid tilting your head up, down, or to the side.

• Size: Make sure your face is centered in the middle of the collecting window.

The wake-up distance of the HIKVISION DS-K1T607PE varies depending on the environment, lighting conditions, and the object being detected. The following table provides reference distances for short, medium, and long wake-up settings.