BOSCH FLEXIDOME MICRO 3100I NUV-3702-F06 (01) PDF Document

To clean the BOSCH FLEXIDOME MICRO 3100I NUV-3702-F06, do not use liquid cleaners or aerosol cleaners.

Do not install the device near any heat sources such as radiators, heaters, stoves, or other equipment (including amplifiers) that produce heat.

Do not spill liquids on the device before installation is completed.

Take precautions to protect the device from power and lightning surges.

Adjust only those controls specified in the operating instructions.

Operate the device only from the type of power source indicated on the label.

Unless qualified, do not attempt to service a damaged device yourself. Refer all servicing to qualified service personnel.

The recommendations for the BOSCH FLEXIDOME MICRO 3100I NUV-3702-F06 are:

Computer with Dual core HyperThreading processor or better.

Graphic card with performance that matches or is better than the resolution of the camera.

Windows 10 or later.

Network access.

Google Chrome, Microsoft Edge, or Mozilla Firefox.

Alternatively, application software such as Video Security Client, Bosch Video Client, or BVMS can be used.

The unit must have a valid IP address and a compatible subnet mask to operate on your network. By default, DHCP is pre-set at the factory to On and so your DHCP server assigns an IP address. With no DHCP server, the default address is automatically assigned via link-local address.

1. Start the web browser.

2. Enter the IP address of the device as the URL.

3. During the initial installation, confirm any security questions that show.

If a RADIUS server is used for network access control (802.1x authentication), you must configure the device before the device can communicate with the network. To configure the device, connect it directly to a computer using a network cable and then set the service-level password.

The BOSCH FLEXIDOME MICRO 3100I NUV-3702-F06 is password-protected. The first time that any user accesses the device, the device will prompt the user to set a password at the service level. Make sure the password obeys these conditions:

8 to 19 characters in length.

Upper and lower case letters.

Minimum of 1 digit.

Minimum of 1 special character.

The following special characters are not allowed: ‘@’, ‘&’, ‘<', '>‘, ‘:’, ‘+’

To view a live stream of the selected video channel:

1. On the left side of the browser, expand the Connection group if necessary.

2. Click the Stream drop-down arrow to see the options.

3. Select the stream you wish to view.

Click the full-screen icon to view the selected stream in full-screen mode. Press Esc on the keyboard to return to the normal viewing window.

To export recorded video, expand the Export group on the left side of the browser if necessary:

1. Select a track in the track list or in the search results.

2. The start and stop date and time are filled for the selected track. If necessary, change the times.

3. In the Time lapse drop-down box, select Original to export the recorded video as its original, or Condensed to export the recorded video condensed to the given output time.

4. In the Location drop-down box, select a target.

5. Click Export to save the video track.

To create a new user, navigate to Configuration > General > User Management and click Add in the section below Authentication modes.

In the box User, fill in the fields:

1. User name: Enter a name with a minimum of 5 and a maximum of 31 characters.

2. Group: Select the appropriate authorization level (live, user, IVA configuration, or service).

3. Type: Select either Password (to enter a new password) or Certificate (for a certificate the user is authorized to use).

4. Click Set to confirm and create a new user.

Notice: Make sure that recording is stopped before synching to the PC.

1. Navigate to the Date/Time configuration page.

2. Click the Sync to PC button to copy your computer’s system time to the camera.

3. Alternatively, enter the current date and time manually.

Navigate to Configuration > Camera > Installer Menu.

Click the Enabled or Disabled check-box to switch the Camera LED on or off.

Select Auto disable to let the camera determine when the LED should be switched off. The camera LED activates when powering on the camera for the first time. The LED deactivates automatically after 5 minutes.

This device has four image rotation options available in the Installer Menu:

0 degrees

90 degrees – upright

180 degrees

270 degrees – upright

Select the option that best suits the device mounting position. The upright modes are good for vertical scenes, such as hallways. If the device is mounted in its normal position, select 0 degrees.

Navigate to Configuration > Camera > Installer Menu.

Click Defaults to restore all settings, including passwords and network settings, to their defaults.

Note: Clicking this button also clears the service-level password. Operators must reset the password before doing anything else.

The White balance options and their additional configuration fields are as follows:

To configure a Privacy mask:

1. Select the mask number from the drop-down list.

2. Click the plus button.

3. Adjust the mask in the image: Double-click on the edges to add or remove nodes, or click and drag the nodes to position them correctly.

4. Check the Enabled check box to activate the related mask.

5. Click the Set button to apply the related changes.

Wiping the storage media deletes all data without recreating a valid file structure. To wipe the recordings:

1. Navigate to Recording > Storage Management.

2. Click a storage medium in the Managed storage media list to select it.

3. Click Edit below the list.

4. Click Wipe in the new window to wipe the recordings in the storage medium.

5. Click Close to close the window.

6. Click Set to apply the changes.

Before starting, make sure to select the correct upload file. Do not interrupt the installation.

1. First, store the firmware file on your hard disk.

2. Navigate to Configuration > Service > Maintenance.

3. Enter the full path for the firmware file in the field or click Browse… to locate and select the file.

4. Click Upload to begin transferring the file to the device. The progress bar allows monitoring of the transfer.

The new firmware is unpacked and the Flash memory is reprogrammed. When the upload is completed successfully, the device reboots automatically.

Notice: A factory default deletes all camera settings including passwords, network settings, and image settings. Remove the camera bubble to access the reset button.

1. Apply power to the camera.

2. Find the hardware reset button on the camera block.

3. Push and hold the reset button for more than 10 seconds. The red LED indicator on the device will begin flashing to show that the hardware reset started.

4. Let the camera complete a self-check. When the self-check completes, the red LED will turn off.

5. Search again for the IP address. Access the camera using the web browser. Set the initial password for the camera.