BOSCH FLEXIDOME MICRO 3100I NUV-3702-F04H (01) PDF Document

The recommendations for connecting to the BOSCH FLEXIDOME MICRO 3100I NUV-3702-F04H are:

– Computer with Dual core HyperThreading processor or better

– Graphic card with performance that matches or is better than the resolution of the camera

– Windows 10 or later

– Network access

– Google Chrome, Microsoft Edge, or Mozilla Firefox

– or –

Application software, for example, Video Security Client, Bosch Video Client or BVMS.

The unit must have a valid IP address and a compatible subnet mask to operate on your network. By default, DHCP is pre-set at the factory to On and so your DHCP server assigns an IP address. With no DHCP server the default address is automatically assigned via link-local address.

1. Start the web browser.

2. Enter the IP address of the device as the URL.

3. During the initial installation, confirm any security questions that show.

If a RADIUS server is used for network access control (802.1x authentication), you must configure the device before the device can communicate with the network. To configure the device, connect it directly to a computer using a network cable and then set the service-level password.

The camera requires a strong password. Follow the prompts in the dialog box, which specifies what is required. The system measures the strength of the password that you enter. Make sure the password obeys these conditions:

– 8 to 19 characters in length

– Upper and lower case letters

– Minimum of 1 digit

– Minimum of 1 special character

These special characters are not allowed: ‘@’, ‘&’, ‘<', '>‘, ‘:’, ‘+’

You can launch the device webpage directly. In the device webpage, an initial password page appears, displaying input fields and a password strength gauge.

1. Fill in the fields User name and Password.

2. Click OK. If the password is correct, the desired page appears.

After a service-level password is set for the device, the device displays a dialog box that prompts users to enter the user name (“service”) and the service-level password every time that they access the device.

The application bar displays the following icons:

Live: Click this icon to view the live video stream.

Playback: Click this icon to play back recorded sequences. This link is only visible if a storage medium has been configured for recording. (With VRM recording, this option is not active.)

Configuration: Click this icon to configure the device.

Dashboard: Click this icon to see detailed system information.

Links: Click this icon to navigate to the Bosch download store.

Logout: Click this icon to log out of the device.

Help: Click this icon to get context-sensitive help for the page you are browsing.

To view a live stream of the selected video channel:

1. On the left side of the browser, expand the Connection group if necessary.

2. Click the Stream drop-down arrow to see the options.

Select the stream you wish to view.

Expand the Search group on the left side of the browser.

– To limit the search to a particular time range, enter the date and times for the start and stop points.

– Select an option from the drop-down box to define a search parameter.

– Click Search.

– The results are listed in a new window. Click a result to play it back.

– Click Back to define a new search.

– Click Last results to display the latest search results.

On the left side of the browser, expand the Export group if necessary:

1. Select a track in the track list or in the search results.

2. The start and stop date and time are filled for the selected track. If necessary, change the times.

3. In the Time lapse drop-down box, select Original, to export the recorded video as its original, Condensed to export the recorded video condensed to the given output time.

4. In the Location drop-down box, select a target.

5. Click Export to save the video track.

6. At the bottom of the page, locate the Export button.

7. Click the Export button.

8. Select a location in your hard drive to store the file.

To create a new user, click Add in the section below Authentication modes.

In the box User, fill in the fields:

1. User name, Enter a name with a minimum of 5 and a maximum of 31 characters.

2. Group, select the appropriate authorization level (live, user, IVA configuration, or service).

3. Type, select either:

– Password for a new password. Use a minimum of 8 and a maximum of 19 characters.

– Certificate for a certificate that the new user is authorized to use.

4. Click Set to confirm and create a new user.

Go to Configuration > Camera > Installer Menu.

Sensor mode:

Make sure the selected sensor mode frame rate is in line with the mains power frequency:

– 50 Hz: 25 fps

– 60 Hz: 30 fps

Image rotation:

Select the option that best suits the device mounting position:

– 0° (Normal position)

– 90° – upright

– 180°

– 270° – upright

The upright modes (90° and 270°) are good for vertical scenes, such as hallways. If the device is mounted in its normal position, select 0°.

Go to Configuration > Camera > Installer Menu.

Reboot device:

Click the Reboot button to restart the device. The entire reboot sequence takes approximately 60 seconds.

Restore settings:

Click Restore to restore all settings, except network settings, to their defaults. Clicking this button also clears the service-level password.

Factory defaults:

Click Defaults to restore all settings, including passwords and network settings, to their defaults. Clicking this button also clears the service-level password.

To determine non-automatically set values:

1. Enter the value for tilt angle, roll angle, height and focal length if the value is known, for example, by measuring the height of the camera above the ground, or reading the focal length from the lens.

2. For each value that is still unknown, select the Calculate check box, then place a calibration element on the camera image. Use these calibration elements to trace individual outlines of the displayed environment in the camera image and define the position and size of these lines and angles.

– Click the vertical line icon to place a vertical line across the image (e.g., door frame, lamp post).

– Click the ground line icon to place a line across the ground in the image (e.g., road marking).

– Click the angle icon to place an angle on the ground in the image (e.g., carpet corner).

3. Adjust the calibration elements to the situation by entering the real size of the line or angle in the corresponding box and dragging the line/angle to position it correctly in the camera image.

Select the appropriate white balance mode from the drop-down list under Configuration > Camera > Color:

– Basic auto mode: Continually adjusts for optimal color reproduction using an average reflectance method. Useful for indoor light sources and colored LED light.

– Standard auto mode: Continually adjusts for optimal color reproduction in an environment with natural light sources.

– Sodium lamp auto mode: Continually adjusts for optimal color reproduction in an environment with sodium vapor light sources.

– Manual RGB mode: Red, Green, and Blue gain can be manually set.

To apply white balance, click Hold to put ATW on hold and save the current color settings. The mode changes to manual.

Select one of the available High dynamic range options under Configuration > Camera > Enhance:

– Off: The device is in single exposure mode and does not have an increased dynamic range through HDR.

– Optimized DR: Select this mode for scenes with greater dynamic range requirements.

– Extreme DR: Further increases performance at an even greater HDR ratio. Due to the increased HDR ratio, there is a greater risk of HDR artifacts in the scene and on moving objects.

To configure a Privacy mask:

1. Select the color of the mask as it will appear in the live video: Auto, Black, Gray, White or Custom color.

2. Select the mask number from the drop-down list.

3. Click the plus button.

4. Adjust the mask in the image:

– Double-click on the edges to add or remove nodes.

– Click and drag the nodes to position them correctly.

5. Check the Enabled check box to activate the related mask.

6. Click the Set button to apply the related changes.

To delete a Privacy mask:

1. Select the mask number from the drop-down list.

2. Click the trashcan icon.

3. Click the Set button to apply the changes.

Available media or iSCSI drives must be transferred to the Managed storage media list, activated, and configured for storage.

1. In the Storage overview section (Configuration > Recording > Storage Management), double-click a storage medium, an iSCSI LUN or one of the other available drives. The medium is added as a target in the Managed storage media list. Newly added media is shown as Not active in the Status column.

2. Click Set to activate all media in the Managed storage media list. The Status column shows all media as Online.

3. Check the box in the Rec. 1 or Rec. 2 column to specify the recording tracks to be recorded on the target selected.

1. Click a storage medium in the Managed storage media list to select it.

2. Click Edit below the list.

3. Click Format in the new window to delete all recordings in the storage medium.

4. Click OK to close the window.

To update the firmware:

1. First, store the firmware file on your hard disk.

2. Navigate to Configuration > Service > Maintenance.

3. Enter the full path for the firmware file in the field or click Browse… to locate and select the file.

4. Click Upload to begin transferring the file to the device. The progress bar allows monitoring of the transfer.

The new firmware is unpacked and the Flash memory is reprogrammed. The time remaining is shown by the message going to reset Reconnecting in … seconds. When the upload is completed successfully, the device reboots automatically.

Steps to complete a hardware reset:

1. Apply power to the camera.

2. Find the hardware reset button on the camera block. Remove the camera bubble to access the reset button.

3. Push and hold the reset button for more than 10 seconds. The red LED indicator on the device will begin flashing to show that the hardware reset started.

4. Let the camera complete a self-check. When the self-check completes, the red LED will turn off.

5. Search again for the IP address. Access the camera using the web browser. Set the initial password for the camera.