BOSCH FLEXIDOME MICRO 3100I NUE-3702-F06 (01) PDF Document

The recommendations for the BOSCH FLEXIDOME MICRO 3100I NUE-3702-F06 are:

Computer with Dual core HyperThreading processor or better

Graphic card with performance that matches or is better than the resolution of the camera

Windows 10 or later

Network access

Google Chrome, Microsoft Edge, or Mozilla Firefox

– or –

Application software, for example, Video Security Client, Bosch Video Client or BVMS.

The unit must have a valid IP address and a compatible subnet mask to operate on your network. By default, DHCP is pre-set at the factory to On and so your DHCP server assigns an IP address. With no DHCP server the default address is automatically assigned via link local address.

1. Start the web browser.

2. Enter the IP address of the device as the URL.

3. During the initial installation, confirm any security questions that show.

If a RADIUS server is used for network access control (802.1x authentication), you must configure the device before the device can communicate with the network. To configure the device, connect it directly to a computer using a network cable and then set the service-level password.

The device is password-protected. The first time that any user accesses the device, the device will prompt the user to set a password at the service level. Make sure the password obeys these conditions:

8 to 19 characters in length

Upper and lower case letters

Minimum of 1 digit

Minimum of 1 special character

These special characters are not allowed: ‘@’, ‘&’, ‘<', '>‘, ‘:’, ‘+’

To create a new user, follow these steps in the Configuration section under User Management:

1. Click Add in the section below Authentication modes.

2. In the box User, fill in the fields:

3. User name: Enter a name with a minimum of 5 and a maximum of 31 characters.

4. Group: Select the appropriate authorization level (live, user, IVA configuration, or service).

5. Type, select either:

– Password for a new password.

– Certificate for a certificate that the new user is authorized to use.

6. Click Set to confirm and create a new user.

If there are multiple devices operating in your system or network, it is important to synchronize their internal clocks.

1. Enter the current date. Since the unit time is controlled by the internal clock, there is no need to enter the day of the week – it is added automatically.

2. Enter the current time or click the Sync to PC button to copy your computer’s system time to the camera.

Note: Make sure that recording is stopped before synching to the PC.

This device has four image rotation options available in the Installer Menu:

0°

90° – upright

180°

270° – upright

Select the option that best suits the device mounting position. The upright modes (90° and 270°) are good for vertical scenes, such as hallways or perimeters. If the device is mounted in its normal position, select 0°.

In the Installer Menu within the Configuration page:

Click Defaults to restore all settings, including passwords and network settings, to their defaults.

Note: Clicking this button also clears the service-level password. Operators must reset the password before doing anything else.

Select the appropriate white balance mode from the drop-down list in the Color settings:

Basic auto: This mode allows the device to continually adjust for optimal color reproduction using an average reflectance method. This is useful indoor light sources and for colored LED light illumination. (Additional fields: R-gain, G-gain, and B-gain only appear when the hold button is pushed.)

Standard auto: This mode allows the device to continually adjust for optimal color reproduction in an environment with natural light sources.

Sodium lamp auto: This mode allows the device to continually adjust for optimal color reproduction in an environment with sodium vapor light sources (street lighting).

Manual RGB: In this mode, the Red, Green, and Blue gain can be manually set to a desired position. (Additional fields: R-gain, G-gain, B-gain).

To Apply white balance: Click Hold to put ATW on hold and save the current color settings. The mode changes to manual.

Privacy Masks block specific areas of a scene from being seen in the camera’s field of view.

To configure a Privacy mask:

– Select the mask number from the drop-down list.

– Click the plus button.

– Adjust the mask in the image:

– Double-click on the edges to add or remove nodes.

– Click and drag the nodes to position them correctly.

– Check the Enabled check box to activate the related mask.

– Click the Set button to apply the related changes.

To delete a Privacy mask:

– Select the mask number from the drop-down list.

– Click the trashcan icon.

– Click the Set button to apply the changes.

Available media or iSCSI drives must be transferred to the Managed storage media list, activated, and configured for storage.

1. In the Storage overview section, double-click a storage medium, an iSCSI LUN or one of the other available drives. The medium is added as a target in the Managed storage media list. Newly added media is shown as Not active in the Status column.

2. Click Set to activate all media in the Managed storage media list. The Status column shows all media as Online.

3. Check the box in the Rec. 1 or Rec. 2 column to specify the recording tracks to be recorded on the target selected.

Formatting the storage media can be necessary to delete all data and recreate a valid file structure to be usable. All recordings on a storage medium can be deleted at any time.

1. Click a storage medium in the Managed storage media list to select it.

2. Click Edit below the list.

3. Click Format in the new window to delete all recordings in the storage medium.

4. Click OK to close the window.

To wipe the recordings from the storage media:

1. Click a storage medium in the Managed storage media list to select it.

2. Click Edit below the list.

3. Click Wipe in the new window to wipe the recordings in the storage medium.

4. Click Close to close the window.

Click Set to apply the changes.

The recording scheduler allows you to link the created recording profiles to the days and times at which the camera’s images are to be recorded.

1. Click the profile to be assigned in the Time periods box.

2. Click a field in the table and, while holding down the left mouse button, drag the cursor across all of the fields to be assigned to the selected profile.

3. Click the No recordings profile in the Time periods box to deselect the intervals.

4. Click Select All to select all of the intervals to be assigned to the selected profile.

5. Click Clear All to deselect all of the intervals.

6. When finished, click Set to save the settings to the device.

After completing configuration, activate the recording schedule and start scheduled recording by clicking Start.

Alarm states can be documented by e-mail.

1. Select On for Send alarm e-mail.

2. Mail server IP address: Enter the IP address of a mail server that operates on the SMTP standard.

3. SMTP port: Select the appropriate SMTP port.

4. SMTP user name: Enter a registered user name for the chosen mail server.

5. SMTP password: Enter the required password for the registered user name.

6. Format: Select the data format (Standard with JPEG or SMS).

7. Destination address: Enter the e-mail address for alarm e-mails.

8. Sender address: Enter a unique name for the e-mail sender.

9. Click Set to apply the changes.

You can click Send Now to test the e-mail function.

To update the firmware:

1. First, store the firmware file on your hard disk.

2. Enter the full path for the firmware file in the field or click Browse… to locate and select the file.

3. Click Upload to begin transferring the file to the device. The progress bar allows monitoring of the transfer.

The new firmware is unpacked and the Flash memory is reprogrammed. The time remaining is shown by the message going to reset Reconnecting in … seconds. When the upload is completed successfully, the device reboots automatically.

Notice! Before starting a firmware update, make sure to select the correct upload file. Do not interrupt the firmware installation.

Notice! A factory default deletes all camera settings including passwords, network settings, and image settings. Complete the following sequence of steps only if you have no other option to restore operation to the camera.

Steps to complete a hardware reset:

1. Apply power to the camera.

2. Find the hardware reset button on the camera block. Remove the camera bubble to access the reset button.

3. Push and hold the reset button for more than 10 seconds. The red LED indicator on the device will begin flashing to show that the hardware reset started.

4. Let the camera complete a self-check. When the self-check completes, the red LED will turn off.

5. Search again for the IP address. Access the camera using the web browser. Set the initial password for the camera.