ASPIRE FLUFFI (01) PDF Document

Free English ASPIRE FLUFFI (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.

CLICK HERE TO DOWNLOAD ASPIRE FLUFFI (01) PDF DOCUMENT

If this is not the document you want for this product, click here to see if we have any other documents for this product.

How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.

What are the technical specifications of the ASPIRE FLUFFI?

The ASPIRE FLUFFI features the following specifications:

Size	1083123 mm
Pod Capacity	3.5 ml
E-liquid Filling	Easy front fill
Coil Type	Non-replaceable 0.6 ohm / 1.0 ohm meshed coil
Battery Capacity	Built-in 1500 mAh
Wattage Range	5 to 20W
Screen	0.69 inch OLED screen
Charging Port	Type-C
Max Charge Current	2A

What is included in the ASPIRE FLUFFI package?

The package contents for the ASPIRE FLUFFI include:

1 * Fluffi Device

1 * Fluffi Pod 3.5ml 0.6 ohm (preinstalled)

1 * Fluffi Pod 3.5ml 1.0 ohm

1 * Type-C Cable

1 * User Manual

How do I fill the pod for my ASPIRE FLUFFI?

To fill the ASPIRE FLUFFI pod, follow these steps:

Step 1. Remove the pod protective cap.

Step 2. Remove the pod from the device.

Step 3. Pull the silicone seal and fill the e-liquid into the pod directly.

Step 4. Close the silicone seal.

Step 5. Put the pod into the groove joint of the device and reattach the pod protective cap to the pod.

Note: Always let the pod stand for 5 minutes after filling so the cotton can be saturated with e-liquid before use.

How do I turn the ASPIRE FLUFFI on and off?

To turn on the ASPIRE FLUFFI, quickly press the power button 5 times. The device will display “aspire”.

To turn off the ASPIRE FLUFFI, quickly press the power button 5 times. The device will display “Shut Down”.

How can I adjust the wattage on the ASPIRE FLUFFI?

To adjust the wattage of your ASPIRE FLUFFI, quickly press the menu button 3 times to enter wattage settings mode. Within 3 flashing seconds, adjust to your desired value by pressing the menu button.

To confirm the wattage setting, you can either wait for 3 seconds or press the fire button once.

How do I change and understand the activation modes on the ASPIRE FLUFFI?

To adjust the activation modes, quickly press the fire button 3 times. The ASPIRE FLUFFI supports three modes:

A Mode: Auto-draw activation.

B Mode: Button activated only.

AB Mode: Both Auto-draw and button activated.

How do the Lock and Unlock functions work on the ASPIRE FLUFFI?

The ASPIRE FLUFFI device will automatically lock when the vaping time exceeds 7 seconds, and the screen will display “Over 7S”. To unlock the device, plug the pod out and then back in.

How do I charge the ASPIRE FLUFFI and what should I expect?

Connect the ASPIRE FLUFFI using the provided Type-C cable. The maximum charge current is 2A, and the recommended charge voltage is 5V.

While charging, the screen will display a growing battery icon. Once fully charged, the screen will stay on for 10 seconds and then shut off. If you press the fire button while charging, the battery will stop charging to ensure safety.

What do the battery level indicators on the ASPIRE FLUFFI screen mean?

The battery level is indicated by bars on the OLED screen as follows:

Level below 0 percent: Empty bar

Level 0 to 20 percent: One bar

Level 21 to 40 percent: Two bars

Level 41 to 60 percent: Three bars

Level 61 to 80 percent: Four bars

Level 81 to 100 percent: Five bars

What safety features and error messages are used by the ASPIRE FLUFFI?

The ASPIRE FLUFFI displays the following messages for protection and troubleshooting:

Vaping Over Time Protection (7s)	“Over 7S”
Open Circuit Protection	“Check Atomizer”
Low Resistance Protection	“Low Res”
Short Circuit Protection	“Atomizer Short”
Low Voltage Protection	“Low Battery”
Abnormal Charging Protection	“Check USB”
Overheat Protection	“Too Hot”

Additionally, if the charging voltage is over 6V or lower than 4.2V, the device will stop charging and display “Check USB” for 5 seconds.

How do I maintain the ASPIRE FLUFFI for optimal performance?

To ensure the longevity and safety of your ASPIRE FLUFFI, follow these maintenance tips:

Condensation: Remember to clean the condensation between the pod and the device regularly.

Coil Safety: Do not inhale from an empty pod to avoid damaging the coil or burning the cotton. Always let a new pod stand for 5 minutes after filling.

Battery Safety: Disconnect the battery from the charger once fully recharged. Do not use the device while it is charging.

General Handling: Keep the device away from overheated or excessively humid conditions. Avoid dropping, burning, puncturing, or crushing the device.

NO IMAGE CONTENT AT THIS TIME. PLEASE CHECK BACK LATER