ASPIRE SPEEDER REVVO (01) PDF Document

To install the battery on your ASPIRE SPEEDER REVVO, follow these steps:

1. Open the battery door.

2. Put in the two 18650 batteries.

3. Close the battery door.

Make sure to use two high-rate 18650 batteries and insert them according to the positive and negative marks.

To turn on the ASPIRE SPEEDER REVVO, press the fire button 5 times in quick succession. The ASPIRE logo will appear on the screen.

To turn off the ASPIRE SPEEDER REVVO, press the fire button 5 times in quick succession. “SYSTEM OFF” will appear on the screen.

To lock or unlock the ASPIRE SPEEDER REVVO, press the fire button 3 times in quick succession. When locked, “LOCKED” will appear on the screen.

To select modes on your ASPIRE SPEEDER REVVO, press the fire button and “+” button simultaneously to enter the mode selection interface. Press “+” or “-” to select between Wattage, Voltage, Bypass, CPS (C1, C2, C3), TC (Ni, Ti, SS, M1, M2, M3) modes.

To adjust the wattage, voltage, or temperature on your ASPIRE SPEEDER REVVO, press the “+” or “-” buttons to adjust the settings. The wattage can be adjusted from 1W to 200W, voltage from 0.1V to 8.4V, and temperature from 100℃ to 315℃ / 200℉ to 600℉.

To enter System Settings on your ASPIRE SPEEDER REVVO, press the fire button and “-” button simultaneously. In System Settings, you can adjust the following:

• STEALTH ON/OFF: Turns the screen display on or off while still allowing the device to function.

• VW/VV/BYPASS/TC(Ni, Ti, SS, M1, M2, M3)/CPS(C1, C2, C3): Selects the desired vaping mode.

• TCR (M1, M2, M3): Sets the Temperature Coefficient of Resistance for custom wire types.

• POWER: Adjusts the wattage in TC mode.

• EXITS: Exits the System Settings menu.

To set the TCR on your ASPIRE SPEEDER REVVO:

1. Enter System Settings (press fire button and “-” button simultaneously).

2. Select TCR (M1, M2, M3).

3. Adjust the TCR value according to the coil material. For example, Ni200 is 600-700, Ti is 300-400, and SS316 is 80-92.

To set the Custom Power Setting (CPS) on your ASPIRE SPEEDER REVVO:

1. Enter System Settings (press fire button and “-” button simultaneously).

2. Select CPS (C1, C2, C3).

3. Adjust the wattage for each second of your puff. For example, if you set C1 to 50W for the first second, 40W for the second, and 30W for the third, the ASPIRE SPEEDER REVVO will fire at these wattages for the duration of your puff.

To charge your ASPIRE SPEEDER REVVO, simply connect the supplied USB cable to the charging port. When the ASPIRE SPEEDER REVVO is charging, the battery icon will display animation and the screen will show “Charging”. When fully charged, the battery icon will be full and the screen will show “Full”.

The main specifications of the ASPIRE SPEEDER REVVO mod are:

Output modes: VW / VV / Bypass / TC (Ni, Ti, SS, TCR, M1, M2, M3) / CPS (C1, C2, C3)

Wattage range: 1-200W

Voltage range: 0.1-8.4V

Temperature range: 100-315°C / 200-600°F

Resistance range: 0.1-3.5ohm

Continuous fire time: 10 seconds

Screen: 0.96 inch OLED

Battery: Dual 18650 high rate cells

Charging: Micro USB port, 2A charging current

The main specifications of the ASPIRE REVVO tank are:

Capacity: 3.6ml

Coil: ARC (Aspire Radial Coil) 0.10-0.16ohm

Filling: Top central spring-loaded fill tube

Airflow: Triple top airflow slots

Drip tip: Wide bore Delrin drip tip

To fill the ASPIRE REVVO tank, simply push your desired e-liquid bottle’s nozzle through the center of the top fill port. The spring-loaded filling tube will open to allow filling and close automatically once the nozzle is removed.

To change the coil on the ASPIRE REVVO tank, follow these steps:

1. Unscrew the drip tip and top cap.

2. Unscrew the mounting screw.

3. Remove the old coil.

4. Replace with a new coil.

5. Screw the mounting screw back in.

6. Screw the top cap and drip tip back on.

The ASPIRE SPEEDER REVVO displays various warning messages to inform you of potential issues:

• “LOW BATTERY” The battery voltage is too low, please charge the ASPIRE SPEEDER REVVO.

• “CHECK ATOMIZER” The atomiser is not connected properly, or the coil resistance is too low or too high.

• “ATOMIZER SHORT” There is a short circuit in the atomiser.

• “NO ATOMIZER” There is no atomiser detected by the ASPIRE SPEEDER REVVO.

• “TOO HOT” The ASPIRE SPEEDER REVVO is overheating, please stop using it and let it cool down.

• “OVER 10S” The fire button has been pressed for more than 10 seconds, which is a safety cut-off.

• “LOW RESISTANCE” The atomiser resistance is too low.

• “HIGH RESISTANCE” The atomiser resistance is too high.

• “IMBALANCE” The batteries are imbalanced, meaning one battery has a significantly lower charge than the other. Charge the ASPIRE SPEEDER REVVO or replace batteries.