ASPIRE EVO75 (01) PDF Document

The ASPIRE EVO75 technical specifications are as follows:

The ASPIRE EVO75 kit includes the following items:

1 Atlantis Evo Tank (0.4 Ohm Coil Pre-installed rated at 40-50w)

1 NX75 Mod

1 USB Cable

1 2ml Replacement Pyrex Tube

1 Extra Coil (0.5 Ohm 35-40W)

1 User Manual

1 Warranty Card

To charge the ASPIRE EVO75, follow these instructions:

Connect the NX75 mod to a charger via the Micro-USB charging port. The maximum current can reach up to 2A. To accomplish 2A charge current, the adaptor output should be 5V/2A.

The screen will show a flashing battery icon. When the battery charge reaches 4.2V or is fully charged, the mod will stop charging and the screen will remain off.

Note that the battery cannot be replaced while charging. Please unplug the USB cable before changing your battery. If the battery charge drops below 0.5V or the battery is incorrectly installed, the mod will stop charging.

While the mod supports passthrough charging, it is recommended to avoid vaping while charging to lengthen the life of the mod.

To fill the Atlantis Evo tank included with the ASPIRE EVO75 kit:

Step 1. Unscrew and remove the top cap.

Step 2. Squirt E-Liquid into the tank. Do not let the tank become completely empty; refill it to avoid dry burning or damage to the atomizer.

Step 3. Reattach the top cap to your tank and begin to vape.

When using a new atomizer, let the tank stand for 2 minutes so the cotton can be saturated with juice before firing.

To replace the atomizer coil in the Atlantis Evo tank:

Step 1. Unscrew the top cap from the Atlantis Evo tank.

Step 2. Remove the Pyrex tube.

Step 3. Replace the atomizer with a new one.

Note: The Atlantis Evo tank is compatible with Aspire Atlantis coils. A 0.4ohm Kanthal Clapton coil is pre-installed.

The ASPIRE EVO75 mod will automatically turn on after installing the battery. The screen will display previous settings, then turn off after 15 seconds of being idle.

Press the fire button 5 times within 2 seconds to either lock or unlock the device.

While the mod is locked, press the fire button for 3 seconds to turn the system off. To turn the mod back on, press the fire button 5 times rapidly.

When the ASPIRE EVO75 is powered on, use the following buttons to switch modes:

Press the W button to switch between VW (Variable Wattage), VV (Variable Voltage), and Bypass modes.

Press the T button to select Temperature Control materials: Ni200, Ti, SS316, or TCR (M1, M2, M3 manual modes).

Note that SS under TC Mode only supports SS316L coils.

Press the “+” button to increase wattage, voltage, or temperature, and the “-” button to decrease them. Pressing and holding either button will change the numbers faster.

To enter or exit Stealth Mode, press the fire button 3 times quickly. In stealth mode, the mod can still fire, but the wattage or temperature settings cannot be adjusted.

Lock/Unlock Buttons: Press “W” and “+” simultaneously for 2 seconds. A lock or unlock symbol will appear in the upper right corner of the screen. When locked, the mod can fire, but settings cannot be adjusted.

Child Lock: Press “W” and “-” simultaneously for 2 seconds to enter or exit Child Lock mode. Use the “+” or “-” buttons to select numbers and the fire button to confirm. The original password is “000”. Select the arrow symbol to reset. Users must input the password to lock or unlock the device.

TCR Settings: Press “T” and “+” simultaneously to change TCR settings. Press the “T” button to select coil material from Ni, Ti, SS, M1, M2, or M3. Press the “W” button to select between “PWR” (Power) and “TCR” (Temperature Control) under M1, M2, and M3 modes. Use the “+” and “-” buttons to change the numbers. TCR numbers can be adjusted from 0.20 to 9.99.

Change Logo: Press “T” and “-” simultaneously for 2 seconds to enter or exit logo settings. Press “+” or “-” to select letters, the fire button to confirm, the “W” button to delete, and the “T” button to toggle between lowercase and capital letters.

The CFBP feature allows you to fine-tune the heat ramp-up (power curve) without connecting to a computer.

Step 1. Press the W button to select C1, C2, or C3 (which are the CFBP modes).

Step 2. While in CFBP, press the W button for 1.5 seconds to enter the CFBP interface.

Step 3. Press the W or T button to set the time in seconds.

Step 4. Press the “+” button to increase wattage or the “-” button to decrease wattage for each second.

Step 5. Press the fire button to save your settings.

Temperature Units: Press the “+” or “-” button all the way past the temperature range limits. The device will automatically switch between Celsius and Fahrenheit.

Continuous Fire Time: The preset time is 10 seconds. After 10 seconds of continuous use, the mod stops firing and flashes “10s”. To adjust this from 5s to 15s, press the “+” or “-” button while the “10s” is flashing.

Firmware Upgrade: Connect your NX75 to a PC. The driver should detect the mod automatically. Use “OpenFile” to choose the correct firmware file and click “Update”. If the process fails, repeat the steps.

Language Selection: Press the fire button while installing the battery to bring up the firmware version screen. You can then select between English and Chinese by pressing the “+” or “-” buttons and confirming with the fire button.

The ASPIRE EVO75 includes the following protection features:

Automatic Cut Off

Short Circuit Protection

Low Resistance Protection

Overheat Protection

Over charge Protection

Over Discharge Protection